diff --git a/examples/simple_repeater/MyMesh.cpp b/examples/simple_repeater/MyMesh.cpp index b50d19d013d..e3db74d7994 100644 --- a/examples/simple_repeater/MyMesh.cpp +++ b/examples/simple_repeater/MyMesh.cpp @@ -992,6 +992,14 @@ void MyMesh::begin(FILESYSTEM *fs) { board.setAdcMultiplier(_prefs.adc_multiplier); #if ENV_INCLUDE_GPS == 1 + // Sync advertised location from prefs to sensors (for geoid correction fallback) + // This allows altitude correction even when GPS doesn't have a fix + if (_prefs.node_lat != 0.0 || _prefs.node_lon != 0.0) { + sensors.node_lat = _prefs.node_lat; + sensors.node_lon = _prefs.node_lon; + MESH_DEBUG_PRINTLN("Synced advertised location to sensors: lat=%.6f, lon=%.6f", sensors.node_lat, + sensors.node_lon); + } applyGpsPrefs(); #endif } diff --git a/platformio.ini b/platformio.ini index 92c94204ccc..3ab975946d5 100644 --- a/platformio.ini +++ b/platformio.ini @@ -9,50 +9,48 @@ ; https://docs.platformio.org/page/projectconf.html [platformio] -extra_configs = - variants/*/platformio.ini - platformio.local.ini +extra_configs = + variants/*/platformio.ini + platformio.local.ini [arduino_base] framework = arduino monitor_speed = 115200 -lib_deps = - SPI - Wire - jgromes/RadioLib @ 7.8.1 - rweather/Crypto @ ^0.4.0 - adafruit/RTClib @ ^2.1.3 - melopero/Melopero RV3028 @ ^1.1.0 - electroniccats/CayenneLPP @ 1.6.1 +lib_deps = + SPI + Wire + jgromes/RadioLib @ 7.8.1 + rweather/Crypto @ ^0.4.0 + adafruit/RTClib @ ^2.1.3 + melopero/Melopero RV3028 @ ^1.1.0 + electroniccats/CayenneLPP @ 1.6.1 build_flags = -w -DNDEBUG -DRADIOLIB_STATIC_ONLY=1 -DRADIOLIB_GODMODE=1 - -D LORA_FREQ=869.618 - -D LORA_BW=62.5 - -D LORA_SF=8 - -D ENABLE_ADVERT_ON_BOOT=1 - -D ENABLE_PRIVATE_KEY_IMPORT=1 ; NOTE: comment these out for more secure firmware - -D ENABLE_PRIVATE_KEY_EXPORT=1 - -D RADIOLIB_EXCLUDE_CC1101=1 - -D RADIOLIB_EXCLUDE_RF69=1 - -D RADIOLIB_EXCLUDE_SX1231=1 - -D RADIOLIB_EXCLUDE_SI443X=1 - -D RADIOLIB_EXCLUDE_RFM2X=1 - -D RADIOLIB_EXCLUDE_SX128X=1 - -D RADIOLIB_EXCLUDE_AFSK=1 - -D RADIOLIB_EXCLUDE_AX25=1 - -D RADIOLIB_EXCLUDE_HELLSCHREIBER=1 - -D RADIOLIB_EXCLUDE_MORSE=1 - -D RADIOLIB_EXCLUDE_APRS=1 - -D RADIOLIB_EXCLUDE_BELL=1 - -D RADIOLIB_EXCLUDE_RTTY=1 - -D RADIOLIB_EXCLUDE_SSTV=1 -build_src_filter = - +<*.cpp> - + - + - + - + - -; ----------------- ESP32 --------------------- + -D LORA_FREQ=869.618 + -D LORA_BW=62.5 + -D LORA_SF=8 + -D ENABLE_ADVERT_ON_BOOT=1 + -D ENABLE_PRIVATE_KEY_IMPORT=1 + -D ENABLE_PRIVATE_KEY_EXPORT=1 + -D RADIOLIB_EXCLUDE_CC1101=1 + -D RADIOLIB_EXCLUDE_RF69=1 + -D RADIOLIB_EXCLUDE_SX1231=1 + -D RADIOLIB_EXCLUDE_SI443X=1 + -D RADIOLIB_EXCLUDE_RFM2X=1 + -D RADIOLIB_EXCLUDE_SX128X=1 + -D RADIOLIB_EXCLUDE_AFSK=1 + -D RADIOLIB_EXCLUDE_AX25=1 + -D RADIOLIB_EXCLUDE_HELLSCHREIBER=1 + -D RADIOLIB_EXCLUDE_MORSE=1 + -D RADIOLIB_EXCLUDE_APRS=1 + -D RADIOLIB_EXCLUDE_BELL=1 + -D RADIOLIB_EXCLUDE_RTTY=1 + -D RADIOLIB_EXCLUDE_SSTV=1 +build_src_filter = + +<*.cpp> + + + + + + + + [esp32_base] extends = arduino_base @@ -60,133 +58,13510 @@ platform = platformio/espressif32@6.11.0 monitor_filters = esp32_exception_decoder extra_scripts = merge-bin.py build_flags = ${arduino_base.build_flags} - -D ESP32_PLATFORM -; -D ESP32_CPU_FREQ=80 ; change it to your need + -D ESP32_PLATFORM build_src_filter = ${arduino_base.build_src_filter} [esp32_ota] -lib_deps = - ESP32Async/ESPAsyncWebServer @ 3.10.3 - file://arch/esp32/AsyncElegantOTA +lib_deps = + ESP32Async/ESPAsyncWebServer @ 3.10.3 + file://arch/esp32/AsyncElegantOTA -; esp32c6 uses arduino framework 3.x -; WARNING: experimental. May not work as stable as other platforms. [esp32c6_base] extends = esp32_base platform = https://github.com/pioarduino/platform-espressif32/releases/download/53.03.13-1/platform-espressif32.zip -; ----------------- NRF52 --------------------- - [nrf52_base] extends = arduino_base platform = nordicnrf52 -platform_packages = - ; use internal fork that includes patch to ble stack to prevent firmware lockup during rapid connect/disconnect - ; https://github.com/meshcore-dev/MeshCore/pull/1177 - ; https://github.com/meshcore-dev/MeshCore/pull/1295 - framework-arduinoadafruitnrf52 @ https://github.com/meshcore-dev/Adafruit_nRF52_Arduino#d541301665b40959682252911e57b11df3ee651a - platformio/toolchain-gccarmnoneeabi@^1.140201.0 +platform_packages = + framework-arduinoadafruitnrf52 @ https://github.com/meshcore-dev/Adafruit_nRF52_Arduino#d541301665b40959682252911e57b11df3ee651a + platformio/toolchain-gccarmnoneeabi@^1.140201.0 extra_scripts = create-uf2.py build_flags = ${arduino_base.build_flags} - -D NRF52_PLATFORM - -D LFS_NO_ASSERT=1 - -D EXTRAFS=1 - -D USE_CC310_HW_CRYPTO=1 -lib_deps = - ${arduino_base.lib_deps} - https://github.com/oltaco/CustomLFS#0.2.3 -; ----------------- RP2040 --------------------- + -D NRF52_PLATFORM + -D LFS_NO_ASSERT=1 + -D EXTRAFS=1 + -D USE_CC310_HW_CRYPTO=1 +lib_deps = + ${arduino_base.lib_deps} + https://github.com/oltaco/CustomLFS#0.2.3 [rp2040_base] extends = arduino_base upload_protocol = picotool board_build.core = earlephilhower -platform = https://github.com/maxgerhardt/platform-raspberrypi.git ; framework-arduinopico @ 1.50600.0+sha.6a1d13e9 +platform = https://github.com/maxgerhardt/platform-raspberrypi.git build_flags = ${arduino_base.build_flags} - -D RP2040_PLATFORM - -; ----------------- STM32 ---------------------- + -D RP2040_PLATFORM [stm32_base] extends = arduino_base -; Pinned pending upstream fix for upstream conversions. -; https://github.com/jgromes/RadioLib/issues/1873 platform = ststm32@19.7.1 extra_scripts = post:arch/stm32/build_hex.py build_flags = ${arduino_base.build_flags} - -D STM32_PLATFORM - -I src/helpers/stm32 - -I $PROJECT_PACKAGES_DIR/framework-arduinoststm32/libraries/SubGhz/src + -D STM32_PLATFORM + -I src/helpers/stm32 + -I $PROJECT_PACKAGES_DIR/framework-arduinoststm32/libraries/SubGhz/src build_src_filter = ${arduino_base.build_src_filter} - + + + lib_deps = ${arduino_base.lib_deps} - file://arch/stm32/Adafruit_LittleFS_stm32 - SubGhz + file://arch/stm32/Adafruit_LittleFS_stm32 + SubGhz [sensor_base] -build_flags = - -D ENV_INCLUDE_GPS=1 - -D ENV_INCLUDE_AHTX0=1 - -D ENV_INCLUDE_BME280=1 - -D ENV_INCLUDE_BMP280=1 - -D ENV_INCLUDE_SHTC3=1 - -D ENV_INCLUDE_SHT4X=1 - -D ENV_INCLUDE_LPS22HB=1 - -D ENV_INCLUDE_INA3221=1 - -D ENV_INCLUDE_INA219=1 - -D ENV_INCLUDE_INA226=1 - -D ENV_INCLUDE_INA260=1 - -D ENV_INCLUDE_MLX90614=1 - -D ENV_INCLUDE_VL53L0X=1 - -D ENV_INCLUDE_BME680=1 - -D ENV_INCLUDE_BMP085=1 -lib_deps = - adafruit/Adafruit INA3221 Library @ ^1.0.1 - adafruit/Adafruit INA219 @ ^1.2.3 - robtillaart/INA226 @ ^0.6.4 - adafruit/Adafruit INA260 Library @ ^1.5.3 - adafruit/Adafruit AHTX0 @ ^2.0.5 - adafruit/Adafruit BME280 Library @ ^2.3.0 - adafruit/Adafruit BMP280 Library @ ^2.6.8 - adafruit/Adafruit SHTC3 Library @ ^1.0.1 - sensirion/Sensirion I2C SHT4x @ ^1.1.2 - arduino-libraries/Arduino_LPS22HB @ ^1.0.2 - adafruit/Adafruit MLX90614 Library @ ^2.1.5 - adafruit/Adafruit_VL53L0X @ ^1.2.4 - stevemarple/MicroNMEA @ ^2.0.6 - adafruit/Adafruit BME680 Library @ ^2.0.4 - adafruit/Adafruit BMP085 Library @ ^1.2.4 - -; ----------------- TESTING --------------------- +build_flags = + -D ENV_INCLUDE_GPS=1 + -D ENV_INCLUDE_AHTX0=1 + -D ENV_INCLUDE_BME280=1 + -D ENV_INCLUDE_BMP280=1 + -D ENV_INCLUDE_SHTC3=1 + -D ENV_INCLUDE_SHT4X=1 + -D ENV_INCLUDE_LPS22HB=1 + -D ENV_INCLUDE_INA3221=1 + -D ENV_INCLUDE_INA219=1 + -D ENV_INCLUDE_INA226=1 + -D ENV_INCLUDE_INA260=1 + -D ENV_INCLUDE_MLX90614=1 + -D ENV_INCLUDE_VL53L0X=1 + -D ENV_INCLUDE_BME680=1 + -D ENV_INCLUDE_BMP085=1 +lib_deps = + adafruit/Adafruit INA3221 Library @ ^1.0.1 + adafruit/Adafruit INA219 @ ^1.2.3 + robtillaart/INA226 @ ^0.6.4 + adafruit/Adafruit INA260 Library @ ^1.5.3 + adafruit/Adafruit AHTX0 @ ^2.0.5 + adafruit/Adafruit BME280 Library @ ^2.3.0 + adafruit/Adafruit BMP280 Library @ ^2.6.8 + adafruit/Adafruit SHTC3 Library @ ^1.0.1 + sensirion/Sensirion I2C SHT4x @ ^1.1.2 + arduino-libraries/Arduino_LPS22HB @ ^1.0.2 + adafruit/Adafruit MLX90614 Library @ ^2.1.5 + adafruit/Adafruit_VL53L0X @ ^1.2.4 + stevemarple/MicroNMEA @ ^2.0.6 + https://github.com/boschsensortec/Bosch-BSEC2-Library#v1.5.2400 + boschsensortec/BME68x Sensor Library@^1.1.40407 + adafruit/Adafruit BME680 Library @ ^2.0.5 + adafruit/Adafruit BMP085 Library @ ^1.2.4 [env:native] platform = native test_framework = googletest build_flags = -std=c++17 - -I src - -I test/mocks + -I src + -I test/mocks test_build_src = yes test_ignore = test_kiss_modem -build_src_filter = - -<*> - +<../src/Utils.cpp> - +<../src/Packet.cpp> - +<../src/helpers/ConfigSerializer.cpp> - +<../src/helpers/DynamicConfigSerializer.cpp> -lib_deps = - google/googletest @ 1.17.0 +build_src_filter = + -<*> + +<../src/Utils.cpp> + +<../src/Packet.cpp> + +<../src/helpers/ConfigSerializer.cpp> + +<../src/helpers/DynamicConfigSerializer.cpp> +lib_deps = + google/googletest @ 1.17.0 [env:native_kiss_modem] platform = native test_framework = googletest build_flags = -std=c++17 - -I test/mocks - -I src - -I examples/kiss_modem + -I test/mocks + -I src + -I examples/kiss_modem test_build_src = yes test_filter = test_kiss_modem -build_src_filter = - -<*> - +<../examples/kiss_modem/KissModem.cpp> -lib_deps = - google/googletest @ 1.17.0 +build_src_filter = + -<*> + +<../examples/kiss_modem/KissModem.cpp> +lib_deps = + google/googletest @ 1.17.0 + +[Meshtiny] +extends = nrf52_base +board = meshtiny +board_build.ldscript = boards/nrf52840_s140_v6.ld +build_flags = ${nrf52_base.build_flags} + -I lib/nrf52/s140_nrf52_6.1.1_API/include + -I lib/nrf52/s140_nrf52_6.1.1_API/include/nrf52 + -I variants/meshtiny + -D USE_SX1262 + -D RADIO_CLASS=CustomSX1262 + -D WRAPPER_CLASS=CustomSX1262Wrapper + -D LORA_TX_POWER=22 + -D SX126X_CURRENT_LIMIT=140 + -D SX126X_RX_BOOSTED_GAIN=1 + -D PIN_3V3_EN=34 + -D MESHTINY + -D UI_HAS_JOYSTICK +build_src_filter = ${nrf52_base.build_src_filter} + +<../variants/meshtiny> + + + + + + +lib_deps = + ${nrf52_base.lib_deps} + adafruit/Adafruit SSD1306 @ ^2.5.13 + end2endzone/NonBlockingRTTTL@^1.3.0 + +[env:Meshtiny_companion_radio_usb] +extends = Meshtiny +build_flags = + ${Meshtiny.build_flags} + -I examples/companion_radio/ui-new + -D MESHTINY + -D PIN_BUZZER=30 + -D DISPLAY_CLASS=SSD1306Display + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D OFFLINE_QUEUE_SIZE=256 + -D ENABLE_USB_INTERFACE +build_src_filter = ${Meshtiny.build_src_filter} + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${Meshtiny.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:Meshtiny_companion_radio_ble] +extends = Meshtiny +build_flags = + ${Meshtiny.build_flags} + -I examples/companion_radio/ui-new + -D MESHTINY + -D PIN_BUZZER=30 + -D DISPLAY_CLASS=SSD1306Display + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D BLE_PIN_CODE=123456 + -D OFFLINE_QUEUE_SIZE=256 +build_src_filter = ${Meshtiny.build_src_filter} + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${Meshtiny.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:Meshtiny_kiss_modem] +extends = Meshtiny +build_src_filter = ${Meshtiny.build_src_filter} + +<../examples/kiss_modem/> + +[waveshare_rp2040_lora] +extends = rp2040_base +board = pico +board_build.filesystem_size = 0.5m +build_flags = ${rp2040_base.build_flags} + -I variants/waveshare_rp2040_lora + -D SX126X_CURRENT_LIMIT=140 + -D USE_SX1262 + -D RADIO_CLASS=CustomSX1262 + -D WRAPPER_CLASS=CustomSX1262Wrapper + -D P_LORA_DIO_1=16 + -D P_LORA_NSS=13 + -D P_LORA_RESET=23 + -D P_LORA_BUSY=18 + -D P_LORA_SCLK=14 + -D P_LORA_MISO=24 + -D P_LORA_MOSI=15 + -D P_LORA_TX_LED=25 + -D SX126X_DIO2_AS_RF_SWITCH=true + -D SX126X_RXEN=17 + -D SX126X_DIO3_TCXO_VOLTAGE=1.8 + -D SX126X_RX_BOOSTED_GAIN=1 + -D LORA_TX_POWER=22 +build_src_filter = ${rp2040_base.build_src_filter} + + + +<../variants/waveshare_rp2040_lora> +lib_deps = ${rp2040_base.lib_deps} + +[env:waveshare_rp2040_lora_repeater] +extends = waveshare_rp2040_lora +build_flags = ${waveshare_rp2040_lora.build_flags} + -D ADVERT_NAME='"RP2040-LoRa Repeater"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 +build_src_filter = ${waveshare_rp2040_lora.build_src_filter} + +<../examples/simple_repeater> + +[env:waveshare_rp2040_lora_repeater_bridge_rs232] +extends = waveshare_rp2040_lora +build_flags = ${waveshare_rp2040_lora.build_flags} + -D ADVERT_NAME='"RS232 Bridge"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 + -D WITH_RS232_BRIDGE=Serial2 + -D WITH_RS232_BRIDGE_RX=9 + -D WITH_RS232_BRIDGE_TX=8 +build_src_filter = ${waveshare_rp2040_lora.build_src_filter} + + + +<../examples/simple_repeater> + +[env:waveshare_rp2040_lora_room_server] +extends = waveshare_rp2040_lora +build_flags = ${waveshare_rp2040_lora.build_flags} + -D ADVERT_NAME='"RP2040-LoRa Room"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D ROOM_PASSWORD='"hello"' +build_src_filter = ${waveshare_rp2040_lora.build_src_filter} + +<../examples/simple_room_server> + +[env:waveshare_rp2040_lora_companion_radio_usb] +extends = waveshare_rp2040_lora +build_flags = ${waveshare_rp2040_lora.build_flags} + -D MAX_CONTACTS=100 + -D MAX_GROUP_CHANNELS=8 + -D ENABLE_USB_INTERFACE +build_src_filter = ${waveshare_rp2040_lora.build_src_filter} + +<../examples/companion_radio/*.cpp> +lib_deps = ${waveshare_rp2040_lora.lib_deps} + densaugeo/base64 @ ~1.4.0 +lib_ignore = BLE + +[env:waveshare_rp2040_lora_terminal_chat] +extends = waveshare_rp2040_lora +build_flags = ${waveshare_rp2040_lora.build_flags} + -D MAX_CONTACTS=100 + -D MAX_GROUP_CHANNELS=1 +build_src_filter = ${waveshare_rp2040_lora.build_src_filter} + +<../examples/simple_secure_chat/main.cpp> +lib_deps = ${waveshare_rp2040_lora.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:waveshare_rp2040_lora_kiss_modem] +extends = waveshare_rp2040_lora +build_src_filter = ${waveshare_rp2040_lora.build_src_filter} + +<../examples/kiss_modem/> + +[WioTrackerL1] +extends = nrf52_base +board = seeed-wio-tracker-l1 +board_build.ldscript = boards/nrf52840_s140_v7.ld +build_flags = ${nrf52_base.build_flags} + ${sensor_base.build_flags} + -I lib/nrf52/s140_nrf52_7.3.0_API/include + -I lib/nrf52/s140_nrf52_7.3.0_API/include/nrf52 + -I variants/wio-tracker-l1 + -D WIO_TRACKER_L1 + -D USE_SX1262 + -D RADIO_CLASS=CustomSX1262 + -D WRAPPER_CLASS=CustomSX1262Wrapper + -D LORA_TX_POWER=22 + -D SX126X_CURRENT_LIMIT=140 + -D SX126X_RX_BOOSTED_GAIN=1 + -D PIN_OLED_RESET=-1 + -D GPS_BAUD_RATE=9600 +build_src_filter = ${nrf52_base.build_src_filter} + + + +<../variants/wio-tracker-l1> + + + + +lib_deps = ${nrf52_base.lib_deps} + ${sensor_base.lib_deps} + adafruit/Adafruit SH110X @ ^2.1.13 + adafruit/Adafruit GFX Library @ ^1.12.1 + +[env:WioTrackerL1_repeater] +extends = WioTrackerL1 +build_src_filter = ${WioTrackerL1.build_src_filter} + +<../examples/simple_repeater> +build_flags = + ${WioTrackerL1.build_flags} + -D ADVERT_NAME='"WioTrackerL1 Repeater"' + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 + -D DISPLAY_CLASS=SH1106Display +lib_deps = ${WioTrackerL1.lib_deps} + adafruit/RTClib @ ^2.1.3 + +[env:WioTrackerL1_room_server] +extends = WioTrackerL1 +build_src_filter = ${WioTrackerL1.build_src_filter} + +<../examples/simple_room_server> +build_flags = ${WioTrackerL1.build_flags} + -D ADVERT_NAME='"WioTrackerL1 Room"' + -D ADMIN_PASSWORD='"password"' + -D ROOM_PASSWORD='"hello"' + -D DISPLAY_CLASS=SH1106Display +lib_deps = ${WioTrackerL1.lib_deps} + adafruit/RTClib @ ^2.1.3 + +[env:WioTrackerL1_companion_radio_usb] +extends = WioTrackerL1 +board_build.ldscript = boards/nrf52840_s140_v7_extrafs.ld +board_upload.maximum_size = 708608 +build_flags = ${WioTrackerL1.build_flags} + -I examples/companion_radio/ui-new + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D DISPLAY_CLASS=SH1106Display + -D UI_HAS_JOYSTICK=1 + -D UI_NO_HIBERNATE + -D OFFLINE_QUEUE_SIZE=256 + -D PIN_BUZZER=12 + -D QSPIFLASH=1 + -D ENABLE_USB_INTERFACE +build_src_filter = ${WioTrackerL1.build_src_filter} + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> + + + + +lib_deps = ${WioTrackerL1.lib_deps} + adafruit/RTClib @ ^2.1.3 + densaugeo/base64 @ ~1.4.0 + end2endzone/NonBlockingRTTTL@^1.3.0 + +[env:WioTrackerL1_companion_radio_ble] +extends = WioTrackerL1 +board_build.ldscript = boards/nrf52840_s140_v7_extrafs.ld +board_upload.maximum_size = 708608 +build_flags = ${WioTrackerL1.build_flags} + -I examples/companion_radio/ui-new + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D BLE_PIN_CODE=123456 + -D BLE_DEBUG_LOGGING=1 + -D OFFLINE_QUEUE_SIZE=256 + -D DISPLAY_CLASS=SH1106Display + -D UI_HAS_JOYSTICK=1 + -D UI_NO_HIBERNATE + -D PIN_BUZZER=12 + -D QSPIFLASH=1 + -D ADVERT_NAME='"@@MAC"' + -D ENV_PIN_SDA=PIN_WIRE1_SDA + -D ENV_PIN_SCL=PIN_WIRE1_SCL +build_src_filter = ${WioTrackerL1.build_src_filter} + + + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = ${WioTrackerL1.lib_deps} + adafruit/RTClib @ ^2.1.3 + densaugeo/base64 @ ~1.4.0 + end2endzone/NonBlockingRTTTL@^1.3.0 + +[env:WioTrackerL1_kiss_modem] +extends = WioTrackerL1 +build_src_filter = ${WioTrackerL1.build_src_filter} + +<../examples/kiss_modem/> + +[GAT562_Mesh_Watch13] +extends = nrf52_base +board = rak4631 +board_check = true +build_flags = ${nrf52_base.build_flags} + ${sensor_base.build_flags} + -UENV_INCLUDE_GPS + -I variants/gat562_mesh_watch13 + -D RAK_4631 + -D RAK_BOARD + -D PIN_BOARD_SCL=14 + -D PIN_BOARD_SDA=13 + -D PIN_OLED_RESET=-1 + -D RADIO_CLASS=CustomSX1262 + -D WRAPPER_CLASS=CustomSX1262Wrapper + -D LORA_TX_POWER=19 + -D SX126X_CURRENT_LIMIT=140 + -D SX126X_RX_BOOSTED_GAIN=1 + -D QSPIFLASH=1 +build_src_filter = ${nrf52_base.build_src_filter} + +<../variants/gat562_mesh_watch13> + + + + + + +lib_deps = + ${nrf52_base.lib_deps} + ${sensor_base.lib_deps} + adafruit/Adafruit SSD1306 @ ^2.5.13 + +[env:GAT562_Mesh_Watch13_companion_radio_ble] +extends = GAT562_Mesh_Watch13 +board_build.ldscript = boards/nrf52840_s140_v6_extrafs.ld +board_upload.maximum_size = 712704 +build_flags = + ${GAT562_Mesh_Watch13.build_flags} + -I examples/companion_radio/ui-new + -D DISPLAY_CLASS=SSD1306Display + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D BLE_PIN_CODE=123456 + -D BLE_DEBUG_LOGGING=1 + -D OFFLINE_QUEUE_SIZE=256 +build_src_filter = ${GAT562_Mesh_Watch13.build_src_filter} + + + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${GAT562_Mesh_Watch13.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:GAT562_Mesh_Watch13_kiss_modem] +extends = GAT562_Mesh_Watch13 +build_src_filter = ${GAT562_Mesh_Watch13.build_src_filter} + +<../examples/kiss_modem/> + +[Heltec_v4_r8] +extends = esp32_base +board = heltec_v4_r8 +build_flags = + ${esp32_base.build_flags} + ${sensor_base.build_flags} + -I variants/heltec_v4_r8 + -D HELTEC_V4_R8 + -D USE_SX1262 + -D ESP32_CPU_FREQ=80 + -D RADIO_CLASS=CustomSX1262 + -D WRAPPER_CLASS=CustomSX1262Wrapper + -D P_LORA_DIO_1=14 + -D P_LORA_NSS=8 + -D P_LORA_RESET=12 + -D P_LORA_BUSY=13 + -D P_LORA_SCLK=9 + -D P_LORA_MISO=11 + -D P_LORA_MOSI=10 + -D P_LORA_PA_POWER=7 + -D P_LORA_KCT8103L_PA_CSD=2 + -D P_LORA_KCT8103L_PA_CTX=5 + -D P_LORA_TX_LED=46 + -D PIN_USER_BTN=0 + -D PIN_VEXT_EN=40 + -D PIN_VEXT_EN_ACTIVE=LOW + -D ADC_MULTIPLIER=5.0715f + -D PIN_VBAT_READ=1 + -D LORA_TX_POWER=10 + -D MAX_LORA_TX_POWER=22 + -D SX126X_REGISTER_PATCH=1 + -D SX126X_DIO2_AS_RF_SWITCH=true + -D SX126X_DIO3_TCXO_VOLTAGE=1.8 + -D SX126X_CURRENT_LIMIT=140 + -D SX126X_RX_BOOSTED_GAIN=1 + -D PIN_GPS_RX=38 + -D PIN_GPS_TX=39 + -D PIN_GPS_EN=42 + -D PIN_GPS_EN_ACTIVE=LOW + -D ENV_INCLUDE_GPS=1 +build_src_filter = ${esp32_base.build_src_filter} + +<../variants/heltec_v4_r8> + + +lib_deps = + ${esp32_base.lib_deps} + ${sensor_base.lib_deps} + +[heltec_v4_r8_oled] +extends = Heltec_v4_r8 +build_flags = + ${Heltec_v4_r8.build_flags} + -D HELTEC_V4_R8_OLED + -D PIN_BOARD_SDA=17 + -D PIN_BOARD_SCL=18 + -D PIN_OLED_RESET=21 +build_src_filter = ${Heltec_v4_r8.build_src_filter} +lib_deps = ${Heltec_v4_r8.lib_deps} + +[heltec_v4_r8_tft] +extends = Heltec_v4_r8 +build_flags = + ${Heltec_v4_r8.build_flags} + -D HELTEC_V4_R8_TFT + -D PIN_BOARD_SDA=17 + -D PIN_BOARD_SCL=18 + -D DISPLAY_SCALE_X=2.5 + -D DISPLAY_SCALE_Y=3.75 + -D PIN_TFT_RST=-1 + -D PIN_TFT_VDD_CTL=-1 + -D PIN_TFT_LEDA_CTL=44 + -D PIN_TFT_LEDA_CTL_ACTIVE=HIGH + -D PIN_TFT_CS=47 + -D PIN_TFT_DC=48 + -D PIN_TFT_SCL=16 + -D PIN_TFT_SDA=15 + -D PIN_TFT_MISO=45 + -D PIN_BUZZER=4 + -D PIN_TOUCH_RST=21 +build_src_filter = ${Heltec_v4_r8.build_src_filter} + + +lib_deps = + ${Heltec_v4_r8.lib_deps} + adafruit/Adafruit ST7735 and ST7789 Library @ ^1.11.0 + end2endzone/NonBlockingRTTTL@^1.3.0 + +[env:heltec_v4_r8_repeater] +extends = heltec_v4_r8_oled +build_flags = + ${heltec_v4_r8_oled.build_flags} + -D DISPLAY_CLASS=SSD1306Display + -D ADVERT_NAME='"Heltec R8 Repeater"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 +build_src_filter = ${heltec_v4_r8_oled.build_src_filter} + + + +<../examples/simple_repeater> +lib_deps = + ${heltec_v4_r8_oled.lib_deps} + ${esp32_ota.lib_deps} + bakercp/CRC32 @ ^2.0.0 + +[env:heltec_v4_r8_room_server] +extends = heltec_v4_r8_oled +build_flags = + ${heltec_v4_r8_oled.build_flags} + -D DISPLAY_CLASS=SSD1306Display + -D ADVERT_NAME='"Heltec R8 Room"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D ROOM_PASSWORD='"hello"' +build_src_filter = ${heltec_v4_r8_oled.build_src_filter} + + + +<../examples/simple_room_server> +lib_deps = + ${heltec_v4_r8_oled.lib_deps} + ${esp32_ota.lib_deps} + +[env:heltec_v4_r8_terminal_chat] +extends = heltec_v4_r8_oled +build_flags = + ${heltec_v4_r8_oled.build_flags} + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=1 +build_src_filter = ${heltec_v4_r8_oled.build_src_filter} + +<../examples/simple_secure_chat/main.cpp> +lib_deps = + ${heltec_v4_r8_oled.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:heltec_v4_r8_companion_radio_usb] +extends = heltec_v4_r8_oled +build_flags = + ${heltec_v4_r8_oled.build_flags} + -I examples/companion_radio/ui-new + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D DISPLAY_CLASS=SSD1306Display + -D ENABLE_USB_INTERFACE +build_src_filter = ${heltec_v4_r8_oled.build_src_filter} + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${heltec_v4_r8_oled.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:heltec_v4_r8_companion_radio_ble] +extends = heltec_v4_r8_oled +build_flags = + ${heltec_v4_r8_oled.build_flags} + -I examples/companion_radio/ui-new + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D DISPLAY_CLASS=SSD1306Display + -D BLE_PIN_CODE=123456 + -D AUTO_SHUTDOWN_MILLIVOLTS=3400 + -D BLE_DEBUG_LOGGING=1 + -D OFFLINE_QUEUE_SIZE=256 + -D ENABLE_WIFI_INTERFACE +build_src_filter = ${heltec_v4_r8_oled.build_src_filter} + + + + + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${heltec_v4_r8_oled.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:heltec_v4_r8_companion_radio_wifi] +extends = heltec_v4_r8_oled +build_flags = + ${heltec_v4_r8_oled.build_flags} + -I examples/companion_radio/ui-new + -D ENABLE_WIFI_INTERFACE + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D OFFLINE_QUEUE_SIZE=256 + -D DISPLAY_CLASS=SSD1306Display + -D WIFI_DEBUG_LOGGING=1 + -D WIFI_SSID='"myssid"' + -D WIFI_PWD='"mypwd"' +build_src_filter = ${heltec_v4_r8_oled.build_src_filter} + + + + + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${heltec_v4_r8_oled.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:heltec_v4_r8_sensor] +extends = heltec_v4_r8_oled +build_flags = + ${heltec_v4_r8_oled.build_flags} + -D ADVERT_NAME='"Heltec R8 Sensor"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D DISPLAY_CLASS=SSD1306Display +build_src_filter = ${heltec_v4_r8_oled.build_src_filter} + + + +<../examples/simple_sensor> +lib_deps = + ${heltec_v4_r8_oled.lib_deps} + ${esp32_ota.lib_deps} + +[env:heltec_v4_r8_tft_repeater] +extends = heltec_v4_r8_tft +build_flags = + ${heltec_v4_r8_tft.build_flags} + -D DISPLAY_CLASS=ST7789LCDDisplay + -D ADVERT_NAME='"Heltec R8 Repeater"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 +build_src_filter = ${heltec_v4_r8_tft.build_src_filter} + + + +<../examples/simple_repeater> +lib_deps = + ${heltec_v4_r8_tft.lib_deps} + ${esp32_ota.lib_deps} + bakercp/CRC32 @ ^2.0.0 + +[env:heltec_v4_r8_tft_room_server] +extends = heltec_v4_r8_tft +build_flags = + ${heltec_v4_r8_tft.build_flags} + -D DISPLAY_CLASS=ST7789LCDDisplay + -D ADVERT_NAME='"Heltec R8 Room"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D ROOM_PASSWORD='"hello"' +build_src_filter = ${heltec_v4_r8_tft.build_src_filter} + + + +<../examples/simple_room_server> +lib_deps = + ${heltec_v4_r8_tft.lib_deps} + ${esp32_ota.lib_deps} + +[env:heltec_v4_r8_tft_terminal_chat] +extends = heltec_v4_r8_tft +build_flags = + ${heltec_v4_r8_tft.build_flags} + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=1 +build_src_filter = ${heltec_v4_r8_tft.build_src_filter} + +<../examples/simple_secure_chat/main.cpp> +lib_deps = + ${heltec_v4_r8_tft.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:heltec_v4_r8_tft_companion_radio_usb] +extends = heltec_v4_r8_tft +build_flags = + ${heltec_v4_r8_tft.build_flags} + -I examples/companion_radio/ui-new + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D DISPLAY_CLASS=ST7789LCDDisplay + -D ENABLE_USB_INTERFACE +build_src_filter = ${heltec_v4_r8_tft.build_src_filter} + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${heltec_v4_r8_tft.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:heltec_v4_r8_tft_companion_radio_ble] +extends = heltec_v4_r8_tft +build_flags = + ${heltec_v4_r8_tft.build_flags} + -I examples/companion_radio/ui-new + -D DISPLAY_CLASS=ST7789LCDDisplay + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D BLE_PIN_CODE=123456 + -D AUTO_SHUTDOWN_MILLIVOLTS=3400 + -D BLE_DEBUG_LOGGING=1 + -D OFFLINE_QUEUE_SIZE=256 +build_src_filter = ${heltec_v4_r8_tft.build_src_filter} + + + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${heltec_v4_r8_tft.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:heltec_v4_r8_tft_companion_radio_wifi] +extends = heltec_v4_r8_tft +build_flags = + ${heltec_v4_r8_tft.build_flags} + -I examples/companion_radio/ui-new + -D ENABLE_WIFI_INTERFACE + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D OFFLINE_QUEUE_SIZE=256 + -D DISPLAY_CLASS=ST7789LCDDisplay + -D WIFI_DEBUG_LOGGING=1 + -D WIFI_SSID='"myssid"' + -D WIFI_PWD='"mypwd"' +build_src_filter = ${heltec_v4_r8_tft.build_src_filter} + + + + + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${heltec_v4_r8_tft.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:heltec_v4_r8_tft_sensor] +extends = heltec_v4_r8_tft +build_flags = + ${heltec_v4_r8_tft.build_flags} + -D ADVERT_NAME='"Heltec R8 Sensor"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D DISPLAY_CLASS=ST7789LCDDisplay +build_src_filter = ${heltec_v4_r8_tft.build_src_filter} + + + +<../examples/simple_sensor> +lib_deps = + ${heltec_v4_r8_tft.lib_deps} + ${esp32_ota.lib_deps} + +[env:heltec_v4_r8_kiss_modem] +extends = Heltec_v4_r8 +build_src_filter = ${Heltec_v4_r8.build_src_filter} + +<../examples/kiss_modem/> + +[env:heltec_v4_r8_tft_kiss_modem] +extends = heltec_v4_r8_tft +build_src_filter = ${heltec_v4_r8_tft.build_src_filter} + +<../examples/kiss_modem/> + +[T_Beam_S3_Supreme_SX1262] +extends = esp32_base +board = t_beams3_supreme +build_flags = + ${esp32_base.build_flags} + -I variants/lilygo_tbeam_supreme_SX1262 + -D TBEAM_SUPREME_SX1262 + -D P_LORA_DIO_0=26 + -D P_LORA_DIO_1=33 + -D P_LORA_NSS=18 + -D P_LORA_RESET=23 + -D P_LORA_SCLK=5 + -D P_LORA_MISO=19 + -D P_LORA_MOSI=27 + -D SX126X_CURRENT_LIMIT=140 + -D SX126X_RX_BOOSTED_GAIN=1 + -D USE_SX1262 + -D RADIO_CLASS=CustomSX1262 + -D WRAPPER_CLASS=CustomSX1262Wrapper + -D DISPLAY_CLASS=SH1106Display + -D DISPLAY_ADDRESS=0x3D + -D LORA_TX_POWER=22 + -D P_LORA_TX_LED=6 + -D PIN_BOARD_SDA=17 + -D PIN_BOARD_SCL=18 + -D PIN_GPS_RX=8 + -D PIN_GPS_TX=9 + -D PIN_GPS_EN=7 + -D PIN_USER_BTN=0 + -D TELEM_BME280_ADDRESS=0x77 + -D ENV_INCLUDE_GPS=1 + -D ENV_INCLUDE_BME280=1 +build_src_filter = ${esp32_base.build_src_filter} + +<../variants/lilygo_tbeam_supreme_SX1262> + + + + + + +board_build.partitions = default_8MB.csv +board_upload.flash_size = 8MB +board_upload.maximum_size = 8388608 +lib_deps = + ${esp32_base.lib_deps} + lewisxhe/XPowersLib @ ^0.2.7 + adafruit/Adafruit SH110X @ ^2.1.13 + stevemarple/MicroNMEA @ ^2.0.6 + adafruit/Adafruit BME280 Library @ ^2.3.0 + +[env:T_Beam_S3_Supreme_SX1262_repeater] +extends = T_Beam_S3_Supreme_SX1262 +build_flags = + ${T_Beam_S3_Supreme_SX1262.build_flags} + -D ADVERT_NAME='"T-Beam S3 Supreme SX1262 Repeater"' + -D ADVERT_LAT=0 + -D ADVERT_LON=0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 +build_src_filter = ${T_Beam_S3_Supreme_SX1262.build_src_filter} + +<../examples/simple_repeater> +lib_deps = + ${T_Beam_S3_Supreme_SX1262.lib_deps} + ${esp32_ota.lib_deps} + +[env:T_Beam_S3_Supreme_SX1262_repeater_bridge_espnow] +extends = T_Beam_S3_Supreme_SX1262 +build_flags = + ${T_Beam_S3_Supreme_SX1262.build_flags} + -D ADVERT_NAME='"ESPNow Bridge"' + -D ADVERT_LAT=0 + -D ADVERT_LON=0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 + -D WITH_ESPNOW_BRIDGE=1 +build_src_filter = ${T_Beam_S3_Supreme_SX1262.build_src_filter} + + + +<../examples/simple_repeater> +lib_deps = + ${T_Beam_S3_Supreme_SX1262.lib_deps} + ${esp32_ota.lib_deps} + +[env:T_Beam_S3_Supreme_SX1262_room_server] +extends = T_Beam_S3_Supreme_SX1262 +build_flags = + ${T_Beam_S3_Supreme_SX1262.build_flags} + -D ADVERT_NAME='"T_Beam_S3_Supreme_SX1262 Room"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D ROOM_PASSWORD='"hello"' +build_src_filter = ${T_Beam_S3_Supreme_SX1262.build_src_filter} + +<../examples/simple_room_server> +lib_deps = + ${T_Beam_S3_Supreme_SX1262.lib_deps} + ${esp32_ota.lib_deps} + +[env:T_Beam_S3_Supreme_SX1262_companion_radio_ble] +extends = T_Beam_S3_Supreme_SX1262 +build_flags = + ${T_Beam_S3_Supreme_SX1262.build_flags} + -I examples/companion_radio/ui-new + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D BLE_PIN_CODE=123456 + -D OFFLINE_QUEUE_SIZE=256 + -D ENABLE_WIFI_INTERFACE +build_src_filter = ${T_Beam_S3_Supreme_SX1262.build_src_filter} + + + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${T_Beam_S3_Supreme_SX1262.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:T_Beam_S3_Supreme_SX1262_companion_radio_wifi] +extends = T_Beam_S3_Supreme_SX1262 +build_flags = + ${T_Beam_S3_Supreme_SX1262.build_flags} + -I examples/companion_radio/ui-new + -D ENABLE_WIFI_INTERFACE + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D OFFLINE_QUEUE_SIZE=256 + -D WIFI_SSID='"WIFI_SSID"' + -D WIFI_PWD='"Password"' +build_src_filter = ${T_Beam_S3_Supreme_SX1262.build_src_filter} + + + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${T_Beam_S3_Supreme_SX1262.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:T_Beam_S3_Supreme_SX1262_kiss_modem] +extends = T_Beam_S3_Supreme_SX1262 +build_src_filter = ${T_Beam_S3_Supreme_SX1262.build_src_filter} + +<../examples/kiss_modem/> + +[Heltec_t096] +extends = nrf52_base +board = heltec_t096 +board_build.ldscript = boards/nrf52840_s140_v6.ld +build_flags = ${nrf52_base.build_flags} + ${sensor_base.build_flags} + -I lib/nrf52/s140_nrf52_6.1.1_API/include + -I lib/nrf52/s140_nrf52_6.1.1_API/include/nrf52 + -I variants/heltec_t096 + -I src/helpers/ui + -D HELTEC_T096 + -D P_LORA_DIO_1=21 + -D P_LORA_NSS=5 + -D P_LORA_RESET=16 + -D P_LORA_BUSY=19 + -D P_LORA_SCLK=40 + -D P_LORA_MISO=14 + -D P_LORA_MOSI=11 + -D P_LORA_TX_LED=28 + -D P_LORA_PA_POWER=30 + -D P_LORA_KCT8103L_PA_CSD=12 + -D P_LORA_KCT8103L_PA_CTX=41 + -D LORA_TX_POWER=9 + -D MAX_LORA_TX_POWER=22 + -D RADIO_CLASS=CustomSX1262 + -D WRAPPER_CLASS=CustomSX1262Wrapper + -D SX126X_DIO2_AS_RF_SWITCH=true + -D SX126X_DIO3_TCXO_VOLTAGE=1.8 + -D SX126X_CURRENT_LIMIT=140 + -D SX126X_RX_BOOSTED_GAIN=1 + -D PIN_VEXT_EN=26 + -D PIN_VEXT_EN_ACTIVE=HIGH + -D PIN_GPS_RX=25 + -D PIN_GPS_TX=23 + -D PIN_GPS_EN=GPS_EN + -D PIN_GPS_EN_ACTIVE=LOW + -D PIN_GPS_RESET=GPS_RESET + -D PIN_GPS_RESET_ACTIVE=LOW + -D GPS_BAUD_RATE=115200 + -D PIN_VBAT_READ=BATTERY_PIN + -D PIN_BAT_CTL=47 + -D DISPLAY_CLASS=ST7735Display + -D DISPLAY_ROTATION=1 +build_src_filter = ${nrf52_base.build_src_filter} + + + + + +<../variants/heltec_t096> + + + + +lib_deps = + ${nrf52_base.lib_deps} + ${sensor_base.lib_deps} + bodmer/TFT_eSPI @ ^2.4.31 +debug_tool = jlink +upload_protocol = nrfutil + +[env:Heltec_t096_repeater] +extends = Heltec_t096 +build_src_filter = ${Heltec_t096.build_src_filter} + +<../examples/simple_repeater> +build_flags = + ${Heltec_t096.build_flags} + -D ADVERT_NAME='"Heltec_t096 Repeater"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 + +[env:Heltec_t096_repeater_bridge_rs232] +extends = Heltec_t096 +build_flags = + ${Heltec_t096.build_flags} + -D ADVERT_NAME='"RS232 Bridge"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 + -D WITH_RS232_BRIDGE=Serial2 + -D WITH_RS232_BRIDGE_RX=9 + -D WITH_RS232_BRIDGE_TX=10 +build_src_filter = ${Heltec_t096.build_src_filter} + + + +<../examples/simple_repeater> + +[env:Heltec_t096_room_server] +extends = Heltec_t096 +build_src_filter = ${Heltec_t096.build_src_filter} + +<../examples/simple_room_server> +build_flags = + ${Heltec_t096.build_flags} + -D ADVERT_NAME='"Heltec_t096 Room"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D ROOM_PASSWORD='"hello"' + +[env:Heltec_t096_sensor] +extends = Heltec_t096 +build_flags = + ${Heltec_t096.build_flags} + -D ADVERT_NAME='"Heltec_t096 Sensor"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D ENV_PIN_SDA=PIN_WIRE1_SDA + -D ENV_PIN_SCL=PIN_WIRE1_SCL +build_src_filter = ${Heltec_t096.build_src_filter} + +<../examples/simple_sensor> +lib_deps = + ${Heltec_t096.lib_deps} + +[env:Heltec_t096_companion_radio_ble] +extends = Heltec_t096 +board_build.ldscript = boards/nrf52840_s140_v6_extrafs.ld +board_upload.maximum_size = 712704 +build_flags = + ${Heltec_t096.build_flags} + -I examples/companion_radio/ui-new + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D BLE_PIN_CODE=123456 + -D ENV_INCLUDE_GPS=1 + -D OFFLINE_QUEUE_SIZE=256 +build_src_filter = ${Heltec_t096.build_src_filter} + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${Heltec_t096.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:Heltec_t096_companion_radio_usb] +extends = Heltec_t096 +board_build.ldscript = boards/nrf52840_s140_v6_extrafs.ld +board_upload.maximum_size = 712704 +build_flags = + ${Heltec_t096.build_flags} + -I examples/companion_radio/ui-new + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D ENABLE_USB_INTERFACE +build_src_filter = ${Heltec_t096.build_src_filter} + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${Heltec_t096.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:Heltec_t096_kiss_modem] +extends = Heltec_t096 +build_src_filter = ${Heltec_t096.build_src_filter} + +<../examples/kiss_modem/> + +[LilyGo_TLora_V2_1_1_6] +extends = esp32_base +board = ttgo-lora32-v1 +build_unflags = -Os +build_type = release +board_build.partitions = min_spiffs.csv +build_flags = + ${esp32_base.build_flags} + ${sensor_base.build_flags} + -UENV_INCLUDE_GPS + -I variants/lilygo_tlora_v2_1 + -Os -ffunction-sections -fdata-sections + -D LILYGO_TLORA + -D P_LORA_DIO_0=26 + -D P_LORA_DIO_1=33 + -D P_LORA_NSS=18 + -D P_LORA_RESET=14 + -D P_LORA_SCLK=5 + -D P_LORA_MISO=19 + -D P_LORA_MOSI=27 + -D P_LORA_TX_LED=25 + -D PIN_BOARD_SDA=21 + -D PIN_BOARD_SCL=22 + -D PIN_VBAT_READ=35 + -D PIN_USER_BTN=0 + -D ARDUINO_LOOP_STACK_SIZE=16384 + -D DISPLAY_CLASS=SSD1306Display + -D RADIO_CLASS=CustomSX1276 + -D WRAPPER_CLASS=CustomSX1276Wrapper + -D SX127X_CURRENT_LIMIT=120 + -D LORA_TX_POWER=20 +build_src_filter = ${esp32_base.build_src_filter} + + + +<../variants/lilygo_tlora_v2_1> + + +lib_deps = + ${esp32_base.lib_deps} + ${sensor_base.lib_deps} + +[env:LilyGo_TLora_V2_1_1_6_repeater] +extends = LilyGo_TLora_V2_1_1_6 +build_src_filter = ${LilyGo_TLora_V2_1_1_6.build_src_filter} + +<../examples/simple_repeater> +build_flags = + ${LilyGo_TLora_V2_1_1_6.build_flags} + -D ADVERT_NAME='"TLora-V2.1-1.6 Repeater"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 +lib_deps = + ${LilyGo_TLora_V2_1_1_6.lib_deps} + ${esp32_ota.lib_deps} + +[env:LilyGo_TLora_V2_1_1_6_terminal_chat] +extends = LilyGo_TLora_V2_1_1_6 +build_flags = + ${LilyGo_TLora_V2_1_1_6.build_flags} + -D MAX_CONTACTS=160 + -D MAX_GROUP_CHANNELS=8 +build_src_filter = ${LilyGo_TLora_V2_1_1_6.build_src_filter} + +<../examples/simple_secure_chat/main.cpp> +lib_deps = + ${LilyGo_TLora_V2_1_1_6.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:LilyGo_TLora_V2_1_1_6_companion_radio_usb] +extends = LilyGo_TLora_V2_1_1_6 +build_flags = + ${LilyGo_TLora_V2_1_1_6.build_flags} + -I examples/companion_radio/ui-new + -D MAX_CONTACTS=160 + -D MAX_GROUP_CHANNELS=8 + -D ENABLE_USB_INTERFACE +build_src_filter = ${LilyGo_TLora_V2_1_1_6.build_src_filter} + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${LilyGo_TLora_V2_1_1_6.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:LilyGo_TLora_V2_1_1_6_companion_radio_ble] +extends = LilyGo_TLora_V2_1_1_6 +build_flags = + ${LilyGo_TLora_V2_1_1_6.build_flags} + -I examples/companion_radio/ui-new + -D MAX_CONTACTS=160 + -D MAX_GROUP_CHANNELS=8 + -D BLE_PIN_CODE=123456 + -D OFFLINE_QUEUE_SIZE=128 +build_src_filter = ${LilyGo_TLora_V2_1_1_6.build_src_filter} + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${LilyGo_TLora_V2_1_1_6.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:LilyGo_TLora_V2_1_1_6_room_server] +extends = LilyGo_TLora_V2_1_1_6 +build_src_filter = ${LilyGo_TLora_V2_1_1_6.build_src_filter} + + + +<../examples/simple_room_server> +build_flags = + ${LilyGo_TLora_V2_1_1_6.build_flags} + -D ADVERT_NAME='"TLora-V2.1-1.6 Room"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D ROOM_PASSWORD='"hello"' +lib_deps = + ${LilyGo_TLora_V2_1_1_6.lib_deps} + ${esp32_ota.lib_deps} + +[env:LilyGo_TLora_V2_1_1_6_companion_radio_wifi] +extends = LilyGo_TLora_V2_1_1_6 +build_flags = + ${LilyGo_TLora_V2_1_1_6.build_flags} + -I examples/companion_radio/ui-new + -D ENABLE_WIFI_INTERFACE + -D MAX_CONTACTS=160 + -D MAX_GROUP_CHANNELS=8 + -D WIFI_SSID='"ssid"' + -D WIFI_PWD='"password"' + -D WIFI_DEBUG_LOGGING=1 + -D OFFLINE_QUEUE_SIZE=128 +build_src_filter = ${LilyGo_TLora_V2_1_1_6.build_src_filter} + + + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${LilyGo_TLora_V2_1_1_6.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:LilyGo_TLora_V2_1_1_6_repeater_bridge_rs232] +extends = LilyGo_TLora_V2_1_1_6 +build_src_filter = ${LilyGo_TLora_V2_1_1_6.build_src_filter} + + + +<../examples/simple_repeater> +build_flags = + ${LilyGo_TLora_V2_1_1_6.build_flags} + -D ADVERT_NAME='"RS232 Bridge"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 + -D WITH_RS232_BRIDGE=Serial2 + -D WITH_RS232_BRIDGE_RX=34 + -D WITH_RS232_BRIDGE_TX=25 +lib_deps = + ${LilyGo_TLora_V2_1_1_6.lib_deps} + ${esp32_ota.lib_deps} + +[env:LilyGo_TLora_V2_1_1_6_repeater_bridge_espnow] +extends = LilyGo_TLora_V2_1_1_6 +build_src_filter = ${LilyGo_TLora_V2_1_1_6.build_src_filter} + + + +<../examples/simple_repeater> +build_flags = + ${LilyGo_TLora_V2_1_1_6.build_flags} + -D ADVERT_NAME='"ESPNow Bridge"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 + -D WITH_ESPNOW_BRIDGE=1 +lib_deps = + ${LilyGo_TLora_V2_1_1_6.lib_deps} + ${esp32_ota.lib_deps} + +[env:LilyGo_TLora_V2_1_1_6_kiss_modem] +extends = LilyGo_TLora_V2_1_1_6 +build_src_filter = ${LilyGo_TLora_V2_1_1_6.build_src_filter} + +<../examples/kiss_modem/> + +[LilyGo_TBeam_1W] +extends = esp32_base +board = t_beam_1w +build_flags = + ${esp32_base.build_flags} + -I variants/lilygo_tbeam_1w + -D TBEAM_1W + + -D RADIO_CLASS=CustomSX1262 + -D WRAPPER_CLASS=CustomSX1262Wrapper + -D P_LORA_DIO_1=1 + -D P_LORA_NSS=15 + -D P_LORA_RESET=3 + -D P_LORA_BUSY=38 + -D P_LORA_SCLK=13 + -D P_LORA_MISO=12 + -D P_LORA_MOSI=11 + + -D SX126X_DIO2_AS_RF_SWITCH=true + -D SX126X_RXEN=21 + -D SX126X_DIO3_TCXO_VOLTAGE=3.0 + -D SX126X_CURRENT_LIMIT=140 + -D SX126X_RX_BOOSTED_GAIN=1 + + -D LORA_TX_POWER=22 + + -D BATT_MIN_MILLIVOLTS=6000 + -D BATT_MAX_MILLIVOLTS=8400 + + -D DISPLAY_CLASS=SH1106Display + + -D PIN_BOARD_SDA=8 + -D PIN_BOARD_SCL=9 + + -D PIN_GPS_TX=5 + -D PIN_GPS_RX=6 + -D PIN_GPS_EN=16 + -D ENV_INCLUDE_GPS=1 + + -D PIN_USER_BTN=17 +build_src_filter = ${esp32_base.build_src_filter} + +<../variants/lilygo_tbeam_1w> + + + + + + +lib_deps = + ${esp32_base.lib_deps} + adafruit/Adafruit SH110X @ ~2.1.13 + stevemarple/MicroNMEA @ ~2.0.6 + +[env:LilyGo_TBeam_1W_repeater] +extends = LilyGo_TBeam_1W +build_flags = + ${LilyGo_TBeam_1W.build_flags} + -D ADVERT_NAME='"T-Beam 1W Repeater"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 + -D PERSISTANT_GPS=1 + -D ENV_SKIP_GPS_DETECT=1 +build_src_filter = ${LilyGo_TBeam_1W.build_src_filter} + +<../examples/simple_repeater> +lib_deps = + ${LilyGo_TBeam_1W.lib_deps} + ${esp32_ota.lib_deps} + +[env:LilyGo_TBeam_1W_room_server] +extends = LilyGo_TBeam_1W +build_flags = + ${LilyGo_TBeam_1W.build_flags} + -D ADVERT_NAME='"T-Beam 1W Room"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D ROOM_PASSWORD='"hello"' + -D PERSISTANT_GPS=1 + -D ENV_SKIP_GPS_DETECT=1 +build_src_filter = ${LilyGo_TBeam_1W.build_src_filter} + +<../examples/simple_room_server> +lib_deps = + ${LilyGo_TBeam_1W.lib_deps} + ${esp32_ota.lib_deps} + +[env:LilyGo_TBeam_1W_companion_radio_usb] +extends = LilyGo_TBeam_1W +build_flags = + ${LilyGo_TBeam_1W.build_flags} + -I examples/companion_radio/ui-new + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D PERSISTANT_GPS=1 + -D ENV_SKIP_GPS_DETECT=1 + -D ENABLE_USB_INTERFACE +build_src_filter = ${LilyGo_TBeam_1W.build_src_filter} + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${LilyGo_TBeam_1W.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:LilyGo_TBeam_1W_companion_radio_ble] +extends = LilyGo_TBeam_1W +build_flags = + ${LilyGo_TBeam_1W.build_flags} + -I examples/companion_radio/ui-new + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D BLE_PIN_CODE=123456 + -D OFFLINE_QUEUE_SIZE=256 + -D PERSISTANT_GPS=1 + -D ENV_SKIP_GPS_DETECT=1 +build_src_filter = ${LilyGo_TBeam_1W.build_src_filter} + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${LilyGo_TBeam_1W.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:LilyGo_TBeam_1W_companion_radio_wifi] +extends = LilyGo_TBeam_1W +build_flags = + ${LilyGo_TBeam_1W.build_flags} + -I examples/companion_radio/ui-new + -D ENABLE_WIFI_INTERFACE + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D OFFLINE_QUEUE_SIZE=256 + -D WIFI_DEBUG_LOGGING=1 + -D WIFI_SSID='"myssid"' + -D WIFI_PWD='"mypwd"' + -D PERSISTANT_GPS=1 + -D ENV_SKIP_GPS_DETECT=1 +build_src_filter = ${LilyGo_TBeam_1W.build_src_filter} + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${LilyGo_TBeam_1W.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:LilyGo_TBeam_1W_repeater_bridge_espnow] +extends = LilyGo_TBeam_1W +build_flags = + ${LilyGo_TBeam_1W.build_flags} + -D ADVERT_NAME='"T-Beam 1W ESPNow Bridge"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 + -D WITH_ESPNOW_BRIDGE=1 + -D PERSISTANT_GPS=1 + -D ENV_SKIP_GPS_DETECT=1 +build_src_filter = ${LilyGo_TBeam_1W.build_src_filter} + + + +<../examples/simple_repeater> +lib_deps = + ${LilyGo_TBeam_1W.lib_deps} + ${esp32_ota.lib_deps} + +[env:LilyGo_TBeam_1W_kiss_modem] +extends = LilyGo_TBeam_1W +build_src_filter = ${LilyGo_TBeam_1W.build_src_filter} + +<../examples/kiss_modem/> + +[meshnology_w12] +extends = esp32_base +board = meshnology_w12 +build_flags = + ${esp32_base.build_flags} + ${sensor_base.build_flags} + -I variants/meshnology_w12 + -D MESHNOLOGY_W12 + -D ESP32_CPU_FREQ=80 + -D RADIO_CLASS=CustomLR2021 + -D WRAPPER_CLASS=CustomLR2021Wrapper + -D USE_LR2021 + -D NEOPIXEL_LED=46 + -D NEOPIXEL_BRIGHTNESS=64 + -D P_LORA_DIO_1=14 + -D LR2021_IRQ_DIO=8 + -D P_LORA_NSS=8 + -D P_LORA_SCLK=9 + -D P_LORA_MOSI=10 + -D P_LORA_MISO=11 + -D P_LORA_RESET=12 + -D P_LORA_BUSY=13 + -D LR2021_TCXO_VOLTAGE=0.0f + -D RF_SWITCH_TABLE + -D P_LORA_LF_PA_POWER=4 + -D P_LORA_HF_PA_POWER=3 + -D PIN_USER_BTN=0 + -D PIN_VEXT_EN=45 + -D PIN_VEXT_EN_ACTIVE=HIGH + -D LORA_TX_POWER=5 + -D MAX_LORA_TX_POWER=13 + -D PIN_GPS_RX=38 + -D PIN_GPS_TX=39 + -D PIN_GPS_RESET=42 + -D PIN_GPS_RESET_ACTIVE=LOW + -D PIN_GPS_EN=48 + -D PIN_GPS_EN_ACTIVE=LOW + -D PIN_VBAT_READ=1 + -D PIN_ADC_CTRL=2 + -D PIN_BOARD_SDA=17 + -D PIN_BOARD_SCL=18 + -D PIN_RESET=47 +build_src_filter = ${esp32_base.build_src_filter} + +<../variants/meshnology_w12> + + +lib_deps = + ${esp32_base.lib_deps} + ${sensor_base.lib_deps} + +[env:meshnology_w12_repeater] +extends = meshnology_w12 +build_flags = + ${meshnology_w12.build_flags} + -D DISPLAY_CLASS=SSD1306Display + -D ADVERT_NAME='"Meshnology W12 Repeater"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 +build_src_filter = ${meshnology_w12.build_src_filter} + + + +<../examples/simple_repeater> +lib_deps = + ${meshnology_w12.lib_deps} + ${esp32_ota.lib_deps} + bakercp/CRC32 @ ^2.0.0 + +[env:meshnology_w12_repeater_bridge_espnow] +extends = meshnology_w12 +build_flags = + ${meshnology_w12.build_flags} + -D DISPLAY_CLASS=SSD1306Display + -D ADVERT_NAME='"ESPNow Bridge"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 + -D WITH_ESPNOW_BRIDGE=1 +build_src_filter = ${meshnology_w12.build_src_filter} + + + + + +<../examples/simple_repeater> +lib_deps = + ${meshnology_w12.lib_deps} + ${esp32_ota.lib_deps} + +[env:meshnology_w12_room_server] +extends = meshnology_w12 +build_flags = + ${meshnology_w12.build_flags} + -D DISPLAY_CLASS=SSD1306Display + -D ADVERT_NAME='"Meshnology W12 Room"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D ROOM_PASSWORD='"hello"' +build_src_filter = ${meshnology_w12.build_src_filter} + + + +<../examples/simple_room_server> +lib_deps = + ${meshnology_w12.lib_deps} + ${esp32_ota.lib_deps} + +[env:meshnology_w12_terminal_chat] +extends = meshnology_w12 +build_flags = + ${meshnology_w12.build_flags} + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=1 +build_src_filter = ${meshnology_w12.build_src_filter} + +<../examples/simple_secure_chat/main.cpp> +lib_deps = + ${meshnology_w12.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:meshnology_w12_companion_radio_usb] +extends = meshnology_w12 +build_flags = + ${meshnology_w12.build_flags} + -I examples/companion_radio/ui-new + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D DISPLAY_CLASS=SSD1306Display +build_src_filter = ${meshnology_w12.build_src_filter} + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${meshnology_w12.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:meshnology_w12_companion_radio_ble] +extends = meshnology_w12 +build_flags = + ${meshnology_w12.build_flags} + -I examples/companion_radio/ui-new + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D DISPLAY_CLASS=SSD1306Display + -D BLE_PIN_CODE=123456 + -D OFFLINE_QUEUE_SIZE=256 +build_src_filter = ${meshnology_w12.build_src_filter} + + + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${meshnology_w12.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:meshnology_w12_companion_radio_wifi] +extends = meshnology_w12 +build_flags = + ${meshnology_w12.build_flags} + -I examples/companion_radio/ui-new + -D ENABLE_WIFI_INTERFACE + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D OFFLINE_QUEUE_SIZE=256 + -D DISPLAY_CLASS=SSD1306Display + -D WIFI_SSID='"myssid"' + -D WIFI_PWD='"mypwd"' +build_src_filter = ${meshnology_w12.build_src_filter} + + + + + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${meshnology_w12.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:meshnology_w12_sensor] +extends = meshnology_w12 +build_flags = + ${meshnology_w12.build_flags} + -D ADVERT_NAME='"Meshnology W12 Sensor"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D ENV_PIN_SDA=3 + -D ENV_PIN_SCL=4 + -D DISPLAY_CLASS=SSD1306Display +build_src_filter = ${meshnology_w12.build_src_filter} + + + +<../examples/simple_sensor> +lib_deps = + ${meshnology_w12.lib_deps} + ${esp32_ota.lib_deps} + +[env:meshnology_w12_kiss_modem] +extends = meshnology_w12 +build_src_filter = ${meshnology_w12.build_src_filter} + +<../examples/kiss_modem/> + +[lora_e5_mini] +extends = stm32_base +board = lora_e5_mini +board_upload.maximum_size = 229376 +build_flags = ${stm32_base.build_flags} + -D RADIO_CLASS=CustomSTM32WLx + -D WRAPPER_CLASS=CustomSTM32WLxWrapper + -D SPI_INTERFACES_COUNT=0 + -D RX_BOOSTED_GAIN=true + -D LORA_TX_POWER=22 + -D SX126X_CURRENT_LIMIT=140 + -D P_LORA_TX_LED=LED_RED + -D PIN_USER_BTN=USER_BTN + -I variants/wio-e5-mini +build_src_filter = ${stm32_base.build_src_filter} + +<../variants/wio-e5-mini> +lib_deps = ${stm32_base.lib_deps} + finitespace/BME280 @ ^3.0.0 + +[env:wio-e5-mini_repeater] +extends = lora_e5_mini +build_flags = ${lora_e5_mini.build_flags} + -D LORA_TX_POWER=22 + -D ADVERT_NAME='"wio-e5-mini Repeater"' + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 +build_src_filter = ${lora_e5_mini.build_src_filter} + +<../examples/simple_repeater/*.cpp> + +[env:wio-e5-mini_sensor] +extends = lora_e5_mini +build_flags = ${lora_e5_mini.build_flags} + -D LORA_TX_POWER=22 + -D ADVERT_NAME='"wio-e5-mini Sensor"' + -D ADMIN_PASSWORD='"password"' +build_src_filter = ${lora_e5_mini.build_src_filter} + +<../examples/simple_sensor> + +[env:wio-e5-mini_companion_radio_usb] +extends = lora_e5_mini +build_flags = ${lora_e5_mini.build_flags} + -I examples/companion_radio/ui-orig + -D LORA_TX_POWER=22 + -D MAX_CONTACTS=100 + -D MAX_GROUP_CHANNELS=8 + -D DISPLAY_CLASS=NullDisplayDriver + -D ENABLE_USB_INTERFACE +build_src_filter = ${lora_e5_mini.build_src_filter} + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-orig/*.cpp> +lib_deps = ${lora_e5_mini.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:wio-e5-mini_kiss_modem] +extends = lora_e5_mini +build_src_filter = ${lora_e5_mini.build_src_filter} + +<../examples/kiss_modem/> + +[Xiao_esp32_C3] +extends = esp32_base +board = seeed_xiao_esp32c3 +build_flags = + ${esp32_base.build_flags} + -I variants/xiao_c3 + -D ESP32_CPU_FREQ=80 + -D PIN_VBAT_READ=D0 + -D P_LORA_DIO_1=D1 + -D P_LORA_NSS=D4 + -D P_LORA_RESET=D2 + -D P_LORA_BUSY=D3 + -D PIN_BOARD_SDA=D6 + -D PIN_BOARD_SCL=D7 + -D USE_SX1262 + -D RADIO_CLASS=CustomSX1262 + -D WRAPPER_CLASS=CustomSX1262Wrapper + -D SX126X_RX_BOOSTED_GAIN=1 + -D LORA_TX_POWER=22 + -D SX126X_RXEN=D5 + -D SX126X_DIO2_AS_RF_SWITCH=true + -D SX126X_DIO3_TCXO_VOLTAGE=1.8 + -D SX126X_CURRENT_LIMIT=140 +build_src_filter = ${esp32_base.build_src_filter} + +<../variants/xiao_c3> + + +lib_deps = + ${esp32_base.lib_deps} + +[env:Xiao_C3_repeater] +extends = Xiao_esp32_C3 +build_src_filter = ${Xiao_esp32_C3.build_src_filter} + +<../examples/simple_repeater/*.cpp> +build_flags = + ${Xiao_esp32_C3.build_flags} + ${sensor_base.build_flags} + -UENV_INCLUDE_GPS + -UENV_INCLUDE_VL53L0X + -D ADVERT_NAME='"Xiao C3 Repeater"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 +lib_deps = + ${Xiao_esp32_C3.lib_deps} + ${sensor_base.lib_deps} + ${esp32_ota.lib_deps} + bakercp/CRC32 @ ^2.0.0 + +[env:Xiao_C3_room_server] +extends = Xiao_esp32_C3 +build_src_filter = ${Xiao_esp32_C3.build_src_filter} + +<../examples/simple_room_server/*.cpp> +build_flags = + ${Xiao_esp32_C3.build_flags} + ${sensor_base.build_flags} + -UENV_INCLUDE_GPS + -UENV_INCLUDE_VL53L0X + -D ADVERT_NAME='"Xiao C3 Room"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D ROOM_PASSWORD='"hello"' +lib_deps = + ${Xiao_esp32_C3.lib_deps} + ${sensor_base.lib_deps} + ${esp32_ota.lib_deps} + bakercp/CRC32 @ ^2.0.0 + +[env:Xiao_C3_companion_radio_ble] +extends = Xiao_esp32_C3 +board_build.partitions = min_spiffs.csv +build_src_filter = ${Xiao_esp32_C3.build_src_filter} + +<../examples/companion_radio/*.cpp> + + +build_flags = + ${Xiao_esp32_C3.build_flags} + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D BLE_PIN_CODE=123456 + -D OFFLINE_QUEUE_SIZE=256 +lib_deps = + ${Xiao_esp32_C3.lib_deps} + ${esp32_ota.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:Xiao_C3_companion_radio_usb] +extends = Xiao_esp32_C3 +build_src_filter = ${Xiao_esp32_C3.build_src_filter} + +<../examples/companion_radio/*.cpp> + + +build_flags = + ${Xiao_esp32_C3.build_flags} + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D OFFLINE_QUEUE_SIZE=256 + -D ENABLE_USB_INTERFACE +lib_deps = + ${Xiao_esp32_C3.lib_deps} + ${esp32_ota.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:Xiao_C3_companion_radio_wifi] +extends = Xiao_esp32_C3 +build_src_filter = ${Xiao_esp32_C3.build_src_filter} + +<../examples/companion_radio/*.cpp> + + + + +build_flags = + ${Xiao_esp32_C3.build_flags} + -D ENABLE_WIFI_INTERFACE + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D OFFLINE_QUEUE_SIZE=256 + -D WIFI_DEBUG_LOGGING=1 + -D WIFI_SSID='"myssid"' + -D WIFI_PWD='"mypwd"' +lib_deps = + ${Xiao_esp32_C3.lib_deps} + ${esp32_ota.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:Xiao_C3_kiss_modem] +extends = Xiao_esp32_C3 +build_src_filter = ${Xiao_esp32_C3.build_src_filter} + +<../examples/kiss_modem/> + +[Xiao_nrf52] +extends = nrf52_base +board = seeed-xiao-afruitnrf52-nrf52840 +board_build.ldscript = boards/nrf52840_s140_v7.ld +build_flags = ${nrf52_base.build_flags} + ${sensor_base.build_flags} + -I lib/nrf52/s140_nrf52_7.3.0_API/include + -I lib/nrf52/s140_nrf52_7.3.0_API/include/nrf52 + -I variants/xiao_nrf52 + -UENV_INCLUDE_GPS + -D NRF52_PLATFORM + -D XIAO_NRF52 + -D USE_SX1262 + -D RADIO_CLASS=CustomSX1262 + -D WRAPPER_CLASS=CustomSX1262Wrapper + -D LORA_TX_POWER=22 + -D P_LORA_TX_LED=11 + -D P_LORA_DIO_1=D1 + -D P_LORA_RESET=D2 + -D P_LORA_BUSY=D3 + -D P_LORA_NSS=D4 + -D SX126X_RXEN=D5 + -D SX126X_TXEN=RADIOLIB_NC + -D SX126X_DIO2_AS_RF_SWITCH=1 + -D SX126X_DIO3_TCXO_VOLTAGE=1.8 + -D SX126X_CURRENT_LIMIT=140 + -D SX126X_RX_BOOSTED_GAIN=1 + -D PIN_WIRE_SCL=D6 + -D PIN_WIRE_SDA=D7 + -D PIN_USER_BTN=PIN_BUTTON1 + -D DISPLAY_CLASS=NullDisplayDriver +build_src_filter = ${nrf52_base.build_src_filter} + + + + + +<../variants/xiao_nrf52> + + +debug_tool = jlink +upload_protocol = nrfutil +lib_deps = ${nrf52_base.lib_deps} + ${sensor_base.lib_deps} + +[env:Xiao_nrf52_companion_radio_ble] +extends = Xiao_nrf52 +board_build.ldscript = boards/nrf52840_s140_v7_extrafs.ld +board_upload.maximum_size = 708608 +build_flags = + ${Xiao_nrf52.build_flags} + -I examples/companion_radio/ui-orig + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D BLE_PIN_CODE=123456 + -D OFFLINE_QUEUE_SIZE=256 + -D QSPIFLASH=1 +build_src_filter = ${Xiao_nrf52.build_src_filter} + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-orig/*.cpp> +lib_deps = + ${Xiao_nrf52.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:Xiao_nrf52_companion_radio_usb] +extends = Xiao_nrf52 +board_build.ldscript = boards/nrf52840_s140_v7_extrafs.ld +board_upload.maximum_size = 708608 +build_flags = + ${Xiao_nrf52.build_flags} + -I examples/companion_radio/ui-orig + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D OFFLINE_QUEUE_SIZE=256 + -D QSPIFLASH=1 + -D ENABLE_USB_INTERFACE +build_src_filter = ${Xiao_nrf52.build_src_filter} + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-orig/*.cpp> +lib_deps = + ${Xiao_nrf52.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:Xiao_nrf52_repeater] +extends = Xiao_nrf52 +build_flags = + ${Xiao_nrf52.build_flags} + -D ADVERT_NAME='"Xiao_nrf52 Repeater"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 +build_src_filter = ${Xiao_nrf52.build_src_filter} + +<../examples/simple_repeater/*.cpp> + +[env:Xiao_nrf52_room_server] +extends = Xiao_nrf52 +build_flags = + ${Xiao_nrf52.build_flags} + -D ADVERT_NAME='"Xiao_nrf52 Room"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' +build_src_filter = ${Xiao_nrf52.build_src_filter} + +<../examples/simple_room_server/*.cpp> + +[env:Xiao_nrf52_kiss_modem] +extends = Xiao_nrf52 +build_flags = + ${Xiao_nrf52.build_flags} +build_src_filter = ${Xiao_nrf52.build_src_filter} + +<../examples/kiss_modem/*.cpp> +lib_deps = + ${Xiao_nrf52.lib_deps} + +[WioTrackerL1-1W] +extends = nrf52_base +board = seeed-wio-tracker-l1 +board_build.ldscript = boards/nrf52840_s140_v7.ld +build_flags = ${nrf52_base.build_flags} + ${sensor_base.build_flags} + -I lib/nrf52/s140_nrf52_7.3.0_API/include + -I lib/nrf52/s140_nrf52_7.3.0_API/include/nrf52 + -I variants/wio-tracker-l1-1w + -D WIO_TRACKER_L1 + -D USE_SX1262 + -D RADIO_CLASS=CustomSX1262 + -D WRAPPER_CLASS=CustomSX1262Wrapper + -D LORA_TX_POWER=22 + -D SX126X_CURRENT_LIMIT=140 + -D SX126X_RX_BOOSTED_GAIN=1 + -D PIN_OLED_RESET=-1 + -D GPS_BAUD_RATE=9600 +build_src_filter = ${nrf52_base.build_src_filter} + + + +<../variants/wio-tracker-l1-1w> + + + + +lib_deps = ${nrf52_base.lib_deps} + ${sensor_base.lib_deps} + adafruit/Adafruit SH110X @ ^2.1.13 + adafruit/Adafruit GFX Library @ ^1.12.1 + +[env:WioTrackerL1-1W_repeater] +extends = WioTrackerL1-1W +build_src_filter = ${WioTrackerL1-1W.build_src_filter} + +<../examples/simple_repeater> +build_flags = + ${WioTrackerL1-1W.build_flags} + -D ADVERT_NAME='"WioTrackerL1 Repeater"' + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 + -D DISPLAY_CLASS=SH1106Display +lib_deps = ${WioTrackerL1-1W.lib_deps} + adafruit/RTClib @ ^2.1.3 + +[env:WioTrackerL1-1W_room_server] +extends = WioTrackerL1-1W +build_src_filter = ${WioTrackerL1-1W.build_src_filter} + +<../examples/simple_room_server> +build_flags = ${WioTrackerL1-1W.build_flags} + -D ADVERT_NAME='"WioTrackerL1 Room"' + -D ADMIN_PASSWORD='"password"' + -D ROOM_PASSWORD='"hello"' + -D DISPLAY_CLASS=SH1106Display +lib_deps = ${WioTrackerL1-1W.lib_deps} + adafruit/RTClib @ ^2.1.3 + +[env:WioTrackerL1-1W_companion_radio_usb] +extends = WioTrackerL1-1W +board_build.ldscript = boards/nrf52840_s140_v7_extrafs.ld +board_upload.maximum_size = 708608 +build_flags = ${WioTrackerL1-1W.build_flags} + -I examples/companion_radio/ui-new + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D DISPLAY_CLASS=SH1106Display + -D UI_HAS_JOYSTICK=1 + -D UI_NO_HIBERNATE + -D OFFLINE_QUEUE_SIZE=256 + -D PIN_BUZZER=12 + -D QSPIFLASH=1 + -D RADIO_FEM_TXGAIN=1 + -D ENABLE_USB_INTERFACE +build_src_filter = ${WioTrackerL1-1W.build_src_filter} + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> + + + + +lib_deps = ${WioTrackerL1-1W.lib_deps} + adafruit/RTClib @ ^2.1.3 + densaugeo/base64 @ ~1.4.0 + end2endzone/NonBlockingRTTTL@^1.3.0 + +[env:WioTrackerL1-1W_companion_radio_ble] +extends = WioTrackerL1-1W +board_build.ldscript = boards/nrf52840_s140_v7_extrafs.ld +board_upload.maximum_size = 708608 +build_flags = ${WioTrackerL1-1W.build_flags} + -I examples/companion_radio/ui-new + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D BLE_PIN_CODE=123456 + -D BLE_DEBUG_LOGGING=1 + -D OFFLINE_QUEUE_SIZE=256 + -D DISPLAY_CLASS=SH1106Display + -D UI_HAS_JOYSTICK=1 + -D UI_NO_HIBERNATE + -D PIN_BUZZER=12 + -D QSPIFLASH=1 + -D RADIO_FEM_TXGAIN=1 + -D ADVERT_NAME='"@@MAC"' + -D ENV_PIN_SDA=PIN_WIRE1_SDA + -D ENV_PIN_SCL=PIN_WIRE1_SCL +build_src_filter = ${WioTrackerL1-1W.build_src_filter} + + + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = ${WioTrackerL1-1W.lib_deps} + adafruit/RTClib @ ^2.1.3 + densaugeo/base64 @ ~1.4.0 + end2endzone/NonBlockingRTTTL@^1.3.0 + +[env:WioTrackerL1-1W_kiss_modem] +extends = WioTrackerL1-1W +build_src_filter = ${WioTrackerL1-1W.build_src_filter} + +<../examples/kiss_modem/> + +[Ebyte_EoRa-S3] +extends = esp32_base +board = ebyte_eora-s3 +build_flags = + ${esp32_base.build_flags} + -I variants/ebyte_eora_s3 + -D EBYTE_EORA_S3 + -D P_LORA_DIO_1=33 + -D P_LORA_NSS=7 + -D P_LORA_RESET=8 + -D P_LORA_BUSY=34 + -D P_LORA_SCLK=5 + -D P_LORA_MISO=3 + -D P_LORA_MOSI=6 + -D P_LORA_TX_LED=37 + -D PIN_VBAT_READ=1 + -D PIN_USER_BTN=0 + -D PIN_BOARD_SDA=18 + -D PIN_BOARD_SCL=17 + + -D PIN_BOARD_SDA=18 + -D PIN_BOARD_SCL=17 + + -D SX126X_DIO2_AS_RF_SWITCH=true + -D SX126X_DIO3_TCXO_VOLTAGE=1.8 + -D SX126X_CURRENT_LIMIT=140 + -D USE_SX1262 + -D RADIO_CLASS=CustomSX1262 + -D WRAPPER_CLASS=CustomSX1262Wrapper + -D LORA_TX_POWER=22 + -D SX126X_RX_BOOSTED_GAIN=1 +build_src_filter = ${esp32_base.build_src_filter} + +<../variants/ebyte_eora_s3> +lib_deps = + ${esp32_base.lib_deps} + adafruit/Adafruit SSD1306 @ ^2.5.13 + +[env:Ebyte_EoRa-S3_Repeater] +extends = Ebyte_EoRa-S3 +build_flags = + ${Ebyte_EoRa-S3.build_flags} + -D DISPLAY_CLASS=SSD1306Display + -D ADVERT_NAME='"EORA_S3-1262 Repeater"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 +build_src_filter = ${Ebyte_EoRa-S3.build_src_filter} + + + +<../examples/simple_repeater> +lib_deps = + ${Ebyte_EoRa-S3.lib_deps} + ${esp32_ota.lib_deps} + +[env:Ebyte_EoRa-S3_terminal_chat] +extends = Ebyte_EoRa-S3 +build_flags = + ${Ebyte_EoRa-S3.build_flags} + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=1 +build_src_filter = ${Ebyte_EoRa-S3.build_src_filter} + +<../examples/simple_secure_chat/main.cpp> +lib_deps = + ${Ebyte_EoRa-S3.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:Ebyte_EoRa-S3_room_server] +extends = Ebyte_EoRa-S3 +build_flags = + ${Ebyte_EoRa-S3.build_flags} + -D DISPLAY_CLASS=SSD1306Display + -D ADVERT_NAME='"EORA_S3-1262 Room"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D ROOM_PASSWORD='"hello"' +build_src_filter = ${Ebyte_EoRa-S3.build_src_filter} + + + +<../examples/simple_room_server> +lib_deps = + ${Ebyte_EoRa-S3.lib_deps} + ${esp32_ota.lib_deps} + +[env:Ebyte_EoRa-S3_companion_radio_usb] +extends = Ebyte_EoRa-S3 +build_flags = + ${Ebyte_EoRa-S3.build_flags} + -I examples/companion_radio/ui-new + -D DISPLAY_CLASS=SSD1306Display + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D ENABLE_USB_INTERFACE +build_src_filter = ${Ebyte_EoRa-S3.build_src_filter} + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${Ebyte_EoRa-S3.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:Ebyte_EoRa-S3_companion_radio_ble] +extends = Ebyte_EoRa-S3 +build_flags = + ${Ebyte_EoRa-S3.build_flags} + -I examples/companion_radio/ui-new + -D DISPLAY_CLASS=SSD1306Display + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D BLE_PIN_CODE=123456 + -D BLE_DEBUG_LOGGING=1 + -D OFFLINE_QUEUE_SIZE=256 +build_src_filter = ${Ebyte_EoRa-S3.build_src_filter} + + + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${Ebyte_EoRa-S3.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:Ebyte_EoRa-S3_kiss_modem] +extends = Ebyte_EoRa-S3 +build_src_filter = ${Ebyte_EoRa-S3.build_src_filter} + +<../examples/kiss_modem/> + +[Heltec_mesh_solar] +extends = nrf52_base +board = heltec_mesh_solar +board_build.ldscript = boards/nrf52840_s140_v6.ld +build_flags = ${nrf52_base.build_flags} + -I src/helpers/nrf52 + -I lib/nrf52/s140_nrf52_6.1.1_API/include + -I lib/nrf52/s140_nrf52_6.1.1_API/include/nrf52 + -I variants/heltec_mesh_solar + -D HELTEC_MESH_SOLAR + -D RADIO_CLASS=CustomSX1262 + -D WRAPPER_CLASS=CustomSX1262Wrapper + -D LORA_TX_POWER=22 + -D SX126X_CURRENT_LIMIT=140 + -D SX126X_RX_BOOSTED_GAIN=1 + -D HAS_EXTERNAL_WATCHDOG + -D EXTERNAL_WATCHDOG_DONE_PIN=9 + -D EXTERNAL_WATCHDOG_WAKE_PIN=10 + -D EXTERNAL_WATCHDOG_FEED_INTERVAL_MS=480000 +build_src_filter = ${nrf52_base.build_src_filter} + + + +<../variants/heltec_mesh_solar> +lib_deps = + ${nrf52_base.lib_deps} + rweather/Crypto @ ^0.4.0 + stevemarple/MicroNMEA @ ^2.0.6 + adafruit/Adafruit NeoPixel@^1.10.0 + https://github.com/NMIoT/meshsolar/archive/dfc5330dad443982e6cdd37a61d33fc7252f468b.zip +debug_tool = jlink +upload_protocol = nrfutil + +[env:Heltec_mesh_solar_repeater] +extends = Heltec_mesh_solar +build_src_filter = ${Heltec_mesh_solar.build_src_filter} + +<../examples/simple_repeater> +build_flags = + ${Heltec_mesh_solar.build_flags} + -D ADVERT_NAME='"Heltec_Mesh_Solar Repeater"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 + +[env:Heltec_mesh_solar_room_server] +extends = Heltec_mesh_solar +build_src_filter = ${Heltec_mesh_solar.build_src_filter} + +<../examples/simple_room_server> +build_flags = + ${Heltec_mesh_solar.build_flags} + -D ADVERT_NAME='"Heltec_Mesh_Solar Room"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D ROOM_PASSWORD='"hello"' + +[env:Heltec_mesh_solar_companion_radio_ble] +extends = Heltec_mesh_solar +board_build.ldscript = boards/nrf52840_s140_v6_extrafs.ld +board_upload.maximum_size = 712704 +build_flags = + ${Heltec_mesh_solar.build_flags} + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D BLE_PIN_CODE=123456 + -D OFFLINE_QUEUE_SIZE=256 +build_src_filter = ${Heltec_mesh_solar.build_src_filter} + + + +<../examples/companion_radio/*.cpp> +lib_deps = + ${Heltec_mesh_solar.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:Heltec_mesh_solar_companion_radio_usb] +extends = Heltec_mesh_solar +board_build.ldscript = boards/nrf52840_s140_v6_extrafs.ld +board_upload.maximum_size = 712704 +build_flags = + ${Heltec_mesh_solar.build_flags} + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D ENABLE_USB_INTERFACE +build_src_filter = ${Heltec_mesh_solar.build_src_filter} + + + +<../examples/companion_radio/*.cpp> +lib_deps = + ${Heltec_mesh_solar.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:Heltec_mesh_solar_kiss_modem] +extends = Heltec_mesh_solar +build_src_filter = ${Heltec_mesh_solar.build_src_filter} + +<../examples/kiss_modem/> + +[Station_G3_ESP32] +extends = esp32_base +board = station-g3-esp32 +build_flags = + ${esp32_base.build_flags} + ${sensor_base.build_flags} + -I variants/station_g3_esp32 + -I src/helpers/ui + -D STATION_G3_ESP32 + -D USE_SX1262 + -D RADIO_CLASS=CustomSX1262 + -D WRAPPER_CLASS=CustomSX1262Wrapper + -D P_LORA_DIO_1=48 + -D P_LORA_NSS=11 + -D P_LORA_RESET=21 + -D P_LORA_BUSY=47 + -D P_LORA_SCLK=12 + -D P_LORA_MISO=14 + -D P_LORA_MOSI=13 + -D P_PA1_EN=9 + -D P_PA1_EN_ACTIVE=HIGH + -D P_PRIMARY_LNA_EN=10 + -D P_PRIMARY_LNA_EN_ACTIVE=LOW + -D LORA_TX_POWER=7 + -D MAX_LORA_TX_POWER=22 + -D PIN_BOARD_SDA=5 + -D PIN_BOARD_SCL=6 + -D PIN_USER_BTN=38 + -D PIN_GPS_RX=15 + -D PIN_GPS_TX=7 + -D SX126X_DIO2_AS_RF_SWITCH=true + -D SX126X_DIO3_TCXO_VOLTAGE=1.8 + -D SX126X_CURRENT_LIMIT=140 + -D SX126X_RX_BOOSTED_GAIN=0 + -D DISPLAY_CLASS=SH1106Display +build_src_filter = ${esp32_base.build_src_filter} + +<../variants/station_g3_esp32> + + + + + + +lib_deps = + ${esp32_base.lib_deps} + ${sensor_base.lib_deps} + adafruit/Adafruit SH110X @ ~2.1.13 + adafruit/Adafruit GFX Library @ ^1.12.1 + +[env:Station_G3_ESP32_repeater] +extends = Station_G3_ESP32 +build_flags = + ${Station_G3_ESP32.build_flags} + -D ADVERT_NAME='"Station G3 ESP32 Repeater"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 +build_src_filter = ${Station_G3_ESP32.build_src_filter} + +<../examples/simple_repeater> +lib_deps = + ${Station_G3_ESP32.lib_deps} + ${esp32_ota.lib_deps} + +[env:Station_G3_ESP32_logging_repeater] +extends = Station_G3_ESP32 +build_flags = + ${Station_G3_ESP32.build_flags} + -D ADVERT_NAME='"Station G3 ESP32 Logging Repeater"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 +build_src_filter = ${Station_G3_ESP32.build_src_filter} + +<../examples/simple_repeater> +lib_deps = + ${Station_G3_ESP32.lib_deps} + ${esp32_ota.lib_deps} + +[env:Station_G3_ESP32_room_server] +extends = Station_G3_ESP32 +build_src_filter = ${Station_G3_ESP32.build_src_filter} + +<../examples/simple_room_server> +build_flags = + ${Station_G3_ESP32.build_flags} + -D ADVERT_NAME='"Station G3 ESP32 Room"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D ROOM_PASSWORD='"hello"' +lib_deps = + ${Station_G3_ESP32.lib_deps} + ${esp32_ota.lib_deps} + +[env:Station_G3_ESP32_companion_radio_usb] +extends = Station_G3_ESP32 +build_flags = + ${Station_G3_ESP32.build_flags} + -I examples/companion_radio/ui-new + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D ENABLE_USB_INTERFACE +build_src_filter = ${Station_G3_ESP32.build_src_filter} + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${Station_G3_ESP32.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:Station_G3_ESP32_companion_radio_ble] +extends = Station_G3_ESP32 +build_flags = + ${Station_G3_ESP32.build_flags} + -I examples/companion_radio/ui-new + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D BLE_PIN_CODE=123456 + -D BLE_DEBUG_LOGGING=1 + -D OFFLINE_QUEUE_SIZE=256 +build_src_filter = ${Station_G3_ESP32.build_src_filter} + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${Station_G3_ESP32.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:Station_G3_ESP32_companion_radio_wifi] +extends = Station_G3_ESP32 +build_flags = + ${Station_G3_ESP32.build_flags} + -I examples/companion_radio/ui-new + -D ENABLE_WIFI_INTERFACE + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D WIFI_DEBUG_LOGGING=1 + -D WIFI_SSID='"myssid"' + -D WIFI_PWD='"mypwd"' + -D OFFLINE_QUEUE_SIZE=256 +build_src_filter = ${Station_G3_ESP32.build_src_filter} + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${Station_G3_ESP32.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:Station_G3_ESP32_kiss_modem] +extends = Station_G3_ESP32 +build_src_filter = ${Station_G3_ESP32.build_src_filter} + +<../examples/kiss_modem/> + +[rak3112] +extends = esp32_base +board = esp32-s3-devkitc-1 +build_flags = + ${esp32_base.build_flags} + ${sensor_base.build_flags} + -I variants/rak3112 + -D RAK_3112=1 + -D ESP32_CPU_FREQ=80 + -D ARDUINO_USB_CDC_ON_BOOT=1 + -D P_LORA_DIO_1=47 + -D P_LORA_NSS=7 + -D P_LORA_RESET=8 + -D P_LORA_BUSY=48 + -D P_LORA_SCLK=5 + -D P_LORA_MISO=3 + -D P_LORA_MOSI=6 + -D USE_SX1262 + -D RADIO_CLASS=CustomSX1262 + -D WRAPPER_CLASS=CustomSX1262Wrapper + -D LORA_TX_POWER=22 + -D P_LORA_TX_LED=46 + -D PIN_BOARD_SDA=9 + -D PIN_BOARD_SCL=40 + -D PIN_USER_BTN=-1 + -D PIN_VEXT_EN=14 + -D SX126X_DIO2_AS_RF_SWITCH=true + -D SX126X_DIO3_TCXO_VOLTAGE=1.8 + -D SX126X_CURRENT_LIMIT=140 + -D SX126X_RX_BOOSTED_GAIN=1 + -D PIN_GPS_RX=43 + -D PIN_GPS_TX=44 +build_src_filter = ${esp32_base.build_src_filter} + +<../variants/rak3112> + + +lib_deps = + ${esp32_base.lib_deps} + ${sensor_base.lib_deps} + +[env:RAK_3112_repeater] +extends = rak3112 +build_flags = + ${rak3112.build_flags} + -D ADVERT_NAME='"RAK3112 Repeater"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 +build_src_filter = ${rak3112.build_src_filter} + +<../examples/simple_repeater> +lib_deps = + ${rak3112.lib_deps} + ${esp32_ota.lib_deps} + bakercp/CRC32 @ ^2.0.0 + +[env:RAK_3112_repeater_bridge_rs232] +extends = rak3112 +build_flags = + ${rak3112.build_flags} + -D ADVERT_NAME='"RS232 Bridge"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 + -D WITH_RS232_BRIDGE=Serial2 + -D WITH_RS232_BRIDGE_RX=5 + -D WITH_RS232_BRIDGE_TX=6 +build_src_filter = ${rak3112.build_src_filter} + + + +<../examples/simple_repeater> +lib_deps = + ${rak3112.lib_deps} + ${esp32_ota.lib_deps} + +[env:RAK_3112_repeater_bridge_espnow] +extends = rak3112 +build_flags = + ${rak3112.build_flags} + -D ADVERT_NAME='"ESPNow Bridge"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 + -D WITH_ESPNOW_BRIDGE=1 +build_src_filter = ${rak3112.build_src_filter} + + + +<../examples/simple_repeater> +lib_deps = + ${rak3112.lib_deps} + ${esp32_ota.lib_deps} + +[env:RAK_3112_room_server] +extends = rak3112 +build_flags = + ${rak3112.build_flags} + -D ADVERT_NAME='"RAK3112 Room"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D ROOM_PASSWORD='"hello"' +build_src_filter = ${rak3112.build_src_filter} + +<../examples/simple_room_server> +lib_deps = + ${rak3112.lib_deps} + ${esp32_ota.lib_deps} + +[env:RAK_3112_terminal_chat] +extends = rak3112 +build_flags = + ${rak3112.build_flags} + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=1 +build_src_filter = ${rak3112.build_src_filter} + +<../examples/simple_secure_chat/main.cpp> +lib_deps = + ${rak3112.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:RAK_3112_companion_radio_usb] +extends = rak3112 +build_flags = + ${rak3112.build_flags} + -I examples/companion_radio/ui-orig + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D ENABLE_USB_INTERFACE +build_src_filter = ${rak3112.build_src_filter} + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-orig/*.cpp> +lib_deps = + ${rak3112.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:RAK_3112_companion_radio_ble] +extends = rak3112 +build_flags = + ${rak3112.build_flags} + -I examples/companion_radio/ui-orig + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D BLE_PIN_CODE=123456 + -D AUTO_SHUTDOWN_MILLIVOLTS=3400 + -D OFFLINE_QUEUE_SIZE=256 + -D ENABLE_WIFI_INTERFACE +build_src_filter = ${rak3112.build_src_filter} + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-orig/*.cpp> +lib_deps = + ${rak3112.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:RAK_3112_companion_radio_wifi] +extends = rak3112 +build_flags = + ${rak3112.build_flags} + -I examples/companion_radio/ui-orig + -D ENABLE_WIFI_INTERFACE + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D WIFI_DEBUG_LOGGING=1 + -D WIFI_SSID='"myssid"' + -D WIFI_PWD='"mypwd"' + -D OFFLINE_QUEUE_SIZE=256 +build_src_filter = ${rak3112.build_src_filter} + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-orig/*.cpp> +lib_deps = + ${rak3112.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:RAK_3112_sensor] +extends = rak3112 +build_flags = + ${rak3112.build_flags} + -D ADVERT_NAME='"RAK3112 v3 Sensor"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D ENV_PIN_SDA=33 + -D ENV_PIN_SCL=34 +build_src_filter = ${rak3112.build_src_filter} + +<../examples/simple_sensor> +lib_deps = + ${rak3112.lib_deps} + ${esp32_ota.lib_deps} + +[env:RAK_3112_kiss_modem] +extends = rak3112 +build_src_filter = ${rak3112.build_src_filter} + +<../examples/kiss_modem/> + +[wio_wm1110] +extends = nrf52_base +board = seeed-xiao-afruitnrf52-nrf52840 +board_build.ldscript = boards/nrf52840_s140_v7.ld +build_flags = ${nrf52_base.build_flags} + ${sensor_base.build_flags} + -I lib/nrf52/s140_nrf52_7.3.0_API/include + -I lib/nrf52/s140_nrf52_7.3.0_API/include/nrf52 + -I variants/wio_wm1110 + -D NRF52_PLATFORM + -D WIO_WM1110 + -D RADIO_CLASS=CustomLR1110 + -D WRAPPER_CLASS=CustomLR1110Wrapper + -D LORA_TX_POWER=22 + -D RX_BOOSTED_GAIN=true + -D P_LORA_DIO_1=40 + -D P_LORA_RESET=42 + -D P_LORA_BUSY=43 + -D P_LORA_NSS=44 + -D P_LORA_SCLK=45 + -D P_LORA_MOSI=46 + -D P_LORA_MISO=47 + -D LR11X0_DIO_AS_RF_SWITCH=true + -D LR11X0_DIO3_TCXO_VOLTAGE=1.8 + -D RF_SWITCH_TABLE + -D ENV_INCLUDE_GPS=0 +build_src_filter = ${nrf52_base.build_src_filter} + + + + + +<../variants/wio_wm1110> +debug_tool = jlink +upload_protocol = jlink +lib_deps = ${nrf52_base.lib_deps} + ${sensor_base.lib_deps} + adafruit/Adafruit LIS3DH @ ^1.2.4 + adafruit/Adafruit SHT4x Library @ ^1.0.4 + +[env:wio_wm1110_repeater] +extends = wio_wm1110 +build_flags = + ${wio_wm1110.build_flags} + -D ADVERT_NAME='"WM1110 Repeater"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 +build_src_filter = ${wio_wm1110.build_src_filter} + +<../examples/simple_repeater/*.cpp> + +[env:wio_wm1110_room_server] +extends = wio_wm1110 +build_flags = + ${wio_wm1110.build_flags} + -D ADVERT_NAME='"WM1110 Room"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D ROOM_PASSWORD='"hello"' +build_src_filter = ${wio_wm1110.build_src_filter} + +<../examples/simple_room_server/*.cpp> + +[env:wio_wm1110_companion_radio_ble] +extends = wio_wm1110 +board_build.ldscript = boards/nrf52840_s140_v7_extrafs.ld +board_upload.maximum_size = 708608 +build_flags = + ${wio_wm1110.build_flags} + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D BLE_PIN_CODE=123456 + -D QSPIFLASH=1 + -D OFFLINE_QUEUE_SIZE=256 +build_src_filter = ${wio_wm1110.build_src_filter} + + + +<../examples/companion_radio/*.cpp> +lib_deps = + ${wio_wm1110.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:wio_wm1110_kiss_modem] +extends = wio_wm1110 +build_src_filter = ${wio_wm1110.build_src_filter} + +<../examples/kiss_modem/> + +[LilyGo_TBeam_SX1262] +extends = esp32_base +board = ttgo-t-beam +build_flags = + ${esp32_base.build_flags} + -I variants/lilygo_tbeam_SX1262 + -D TBEAM_SX1262 + -D P_LORA_DIO_0=26 + -D P_LORA_DIO_1=33 + -D P_LORA_NSS=18 + -D P_LORA_RESET=23 + -D P_LORA_SCLK=5 + -D P_LORA_MISO=19 + -D P_LORA_MOSI=27 + -D SX126X_DIO2_AS_RF_SWITCH=true + -D SX126X_DIO3_TCXO_VOLTAGE=1.8 + -D SX126X_CURRENT_LIMIT=140 + -D SX126X_RX_BOOSTED_GAIN=1 + -D USE_SX1262 + -D RADIO_CLASS=CustomSX1262 + -D WRAPPER_CLASS=CustomSX1262Wrapper + -D DISPLAY_CLASS=SSD1306Display + -D LORA_TX_POWER=22 + -D P_LORA_TX_LED=4 + -D PIN_BOARD_SDA=21 + -D PIN_BOARD_SCL=22 + -D PIN_GPS_RX=12 + -D PIN_GPS_TX=34 + -D PIN_USER_BTN=38 + -D ENV_INCLUDE_GPS=1 +build_src_filter = ${esp32_base.build_src_filter} + +<../variants/lilygo_tbeam_SX1262> + + + + + + +board_build.partitions = min_spiffs.csv +lib_deps = + ${esp32_base.lib_deps} + lewisxhe/XPowersLib@^0.2.7 + adafruit/Adafruit SSD1306 @ ^2.5.13 + stevemarple/MicroNMEA @ ^2.0.6 + +[env:Tbeam_SX1262_companion_radio_ble] +extends = LilyGo_TBeam_SX1262 +board_build.upload.maximum_ram_size = 2000000 +build_flags = + ${LilyGo_TBeam_SX1262.build_flags} + -I examples/companion_radio/ui-new + -D MAX_CONTACTS=160 + -D MAX_GROUP_CHANNELS=8 + -D BLE_PIN_CODE=123456 + -D OFFLINE_QUEUE_SIZE=128 +build_src_filter = ${LilyGo_TBeam_SX1262.build_src_filter} + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${LilyGo_TBeam_SX1262.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:Tbeam_SX1262_repeater] +extends = LilyGo_TBeam_SX1262 +build_flags = + ${LilyGo_TBeam_SX1262.build_flags} + -D ADVERT_NAME='"Tbeam SX1262 Repeater"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 +build_src_filter = ${LilyGo_TBeam_SX1262.build_src_filter} + +<../examples/simple_repeater> +lib_deps = + ${LilyGo_TBeam_SX1262.lib_deps} + ${esp32_ota.lib_deps} + +[env:Tbeam_SX1262_repeater_bridge_espnow] +extends = LilyGo_TBeam_SX1262 +build_flags = + ${LilyGo_TBeam_SX1262.build_flags} + -D ADVERT_NAME='"ESPNow Bridge"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 + -D WITH_ESPNOW_BRIDGE=1 +build_src_filter = ${LilyGo_TBeam_SX1262.build_src_filter} + + + +<../examples/simple_repeater> +lib_deps = + ${LilyGo_TBeam_SX1262.lib_deps} + ${esp32_ota.lib_deps} + +[env:Tbeam_SX1262_room_server] +extends = LilyGo_TBeam_SX1262 +build_flags = + ${LilyGo_TBeam_SX1262.build_flags} + -D ADVERT_NAME='"Tbeam SX1262 Room"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D ROOM_PASSWORD='"hello"' +build_src_filter = ${LilyGo_TBeam_SX1262.build_src_filter} + +<../examples/simple_room_server> +lib_deps = + ${LilyGo_TBeam_SX1262.lib_deps} + ${esp32_ota.lib_deps} + +[env:Tbeam_SX1262_kiss_modem] +extends = LilyGo_TBeam_SX1262 +build_src_filter = ${LilyGo_TBeam_SX1262.build_src_filter} + +<../examples/kiss_modem/> + +[Heltec_RC32] +extends = esp32_base +board = heltec-rc32 +board_build.partitions = default_16MB.csv +build_flags = + ${esp32_base.build_flags} + ${sensor_base.build_flags} + -I variants/heltec_rc32 + -I src/helpers/ui + -D HELTEC_RC32 + -D USE_SX1262 + -D ESP32_CPU_FREQ=160 + -D RADIO_CLASS=CustomSX1262 + -D WRAPPER_CLASS=CustomSX1262Wrapper + -D P_LORA_DIO_1=14 + -D P_LORA_NSS=10 + -D P_LORA_RESET=9 + -D P_LORA_BUSY=1 + -D P_LORA_SCLK=11 + -D P_LORA_MISO=13 + -D P_LORA_MOSI=12 + -D LORA_TX_POWER=22 + -D PIN_USER_BTN=0 + -D PIN_BOARD_SDA=21 + -D PIN_BOARD_SCL=18 + -D SENSOR_POWER_CTRL_PIN=46 + -D SENSOR_POWER_ON=HIGH + -D SENSOR_RST_PIN=2 + -D P_LORA_TX_LED=47 + -D PIN_BUZZER=48 + -D PIN_TFT_SCL=17 + -D PIN_TFT_SDA=38 + -D PIN_TFT_CS=39 + -D PIN_TFT_DC=16 + -D PIN_TFT_RST=4 + -D PIN_TFT_EN=6 + -D PIN_TFT_EN_ACTIVE=LOW + -D PIN_TFT_BL=5 + -D PIN_TFT_BL_ACTIVE=HIGH + -D SPI_FREQUENCY=8000000 + -D PIN_GPS_TX=44 + -D PIN_GPS_RX=43 + -D PIN_GPS_EN=45 + -D PIN_GPS_EN_ACTIVE=HIGH + -D PIN_GPS_RESET=40 + -D PIN_GPS_RESET_ACTIVE=LOW + -D PIN_GPS_PPS=41 + -D GPS_BAUD_RATE=9600 + -D ENV_INCLUDE_GPS=1 + -D PIN_ADC_CTRL=15 + -D PIN_VBAT_READ=7 + -D ADC_CTRL_ENABLED=HIGH + -D ADC_MULTIPLIER=4.9 + -D SX126X_DIO2_AS_RF_SWITCH=true + -D SX126X_DIO3_TCXO_VOLTAGE=1.8 + -D SX126X_CURRENT_LIMIT=140 + -D SX126X_RX_BOOSTED_GAIN=1 + -D SX126X_REGISTER_PATCH=1 +build_src_filter = ${esp32_base.build_src_filter} + +<../variants/heltec_rc32> + + +lib_deps = + ${esp32_base.lib_deps} + ${sensor_base.lib_deps} + +[Heltec_RC32_with_display] +extends = Heltec_RC32 +build_flags = + ${Heltec_RC32.build_flags} + -D HELTEC_RC32_WITH_DISPLAY + -D DISPLAY_CLASS=NV3001BDisplay +build_src_filter = ${Heltec_RC32.build_src_filter} + + + + +lib_deps = + ${Heltec_RC32.lib_deps} + +[env:heltec_rc32_without_display_repeater] +extends = Heltec_RC32 +build_flags = + ${Heltec_RC32.build_flags} + -D ADVERT_NAME='"Heltec RC32 Repeater"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 +build_src_filter = ${Heltec_RC32.build_src_filter} + +<../examples/simple_repeater> +lib_deps = + ${Heltec_RC32.lib_deps} + ${esp32_ota.lib_deps} + bakercp/CRC32 @ ^2.0.0 + +[env:heltec_rc32_without_display_repeater_bridge_espnow] +extends = Heltec_RC32 +build_flags = + ${Heltec_RC32.build_flags} + -D ADVERT_NAME='"ESPNow Bridge"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 + -D WITH_ESPNOW_BRIDGE=1 +build_src_filter = ${Heltec_RC32.build_src_filter} + + + +<../examples/simple_repeater> +lib_deps = + ${Heltec_RC32.lib_deps} + ${esp32_ota.lib_deps} + +[env:heltec_rc32_without_display_room_server] +extends = Heltec_RC32 +build_flags = + ${Heltec_RC32.build_flags} + -D ADVERT_NAME='"Heltec RC32 Room"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D ROOM_PASSWORD='"hello"' +build_src_filter = ${Heltec_RC32.build_src_filter} + +<../examples/simple_room_server> +lib_deps = + ${Heltec_RC32.lib_deps} + ${esp32_ota.lib_deps} + +[env:heltec_rc32_without_display_companion_radio_usb] +extends = Heltec_RC32 +build_flags = + ${Heltec_RC32.build_flags} + -I examples/companion_radio/ui-new + -D DISPLAY_CLASS=NullDisplayDriver + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D ENABLE_USB_INTERFACE +build_src_filter = ${Heltec_RC32.build_src_filter} + + + + + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${Heltec_RC32.lib_deps} + densaugeo/base64 @ ~1.4.0 + end2endzone/NonBlockingRTTTL@^1.3.0 + +[env:heltec_rc32_without_display_companion_radio_ble] +extends = Heltec_RC32 +build_flags = + ${Heltec_RC32.build_flags} + -I examples/companion_radio/ui-new + -D DISPLAY_CLASS=NullDisplayDriver + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D BLE_PIN_CODE=123456 + -D AUTO_SHUTDOWN_MILLIVOLTS=3400 + -D BLE_DEBUG_LOGGING=1 + -D OFFLINE_QUEUE_SIZE=256 +build_src_filter = ${Heltec_RC32.build_src_filter} + + + + + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${Heltec_RC32.lib_deps} + densaugeo/base64 @ ~1.4.0 + end2endzone/NonBlockingRTTTL@^1.3.0 + +[env:heltec_rc32_without_display_companion_radio_wifi] +extends = Heltec_RC32 +build_flags = + ${Heltec_RC32.build_flags} + -I examples/companion_radio/ui-new + -D ENABLE_WIFI_INTERFACE + -D DISPLAY_CLASS=NullDisplayDriver + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D WIFI_DEBUG_LOGGING=1 + -D WIFI_SSID='"myssid"' + -D WIFI_PWD='"mypwd"' + -D OFFLINE_QUEUE_SIZE=256 +build_src_filter = ${Heltec_RC32.build_src_filter} + + + + + + + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${Heltec_RC32.lib_deps} + densaugeo/base64 @ ~1.4.0 + end2endzone/NonBlockingRTTTL@^1.3.0 + +[env:heltec_rc32_without_display_sensor] +extends = Heltec_RC32 +build_flags = + ${Heltec_RC32.build_flags} + -D ADVERT_NAME='"Heltec RC32 Sensor"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D ENV_PIN_SDA=21 + -D ENV_PIN_SCL=18 +build_src_filter = ${Heltec_RC32.build_src_filter} + +<../examples/simple_sensor> +lib_deps = + ${Heltec_RC32.lib_deps} + ${esp32_ota.lib_deps} + +[env:heltec_rc32_repeater] +extends = Heltec_RC32_with_display +build_flags = + ${Heltec_RC32_with_display.build_flags} + -D ADVERT_NAME='"Heltec RC32 Repeater"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 +build_src_filter = ${Heltec_RC32_with_display.build_src_filter} + +<../examples/simple_repeater> +lib_deps = + ${Heltec_RC32_with_display.lib_deps} + ${esp32_ota.lib_deps} + bakercp/CRC32 @ ^2.0.0 + +[env:heltec_rc32_repeater_bridge_espnow] +extends = Heltec_RC32_with_display +build_flags = + ${Heltec_RC32_with_display.build_flags} + -D ADVERT_NAME='"ESPNow Bridge"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 + -D WITH_ESPNOW_BRIDGE=1 +build_src_filter = ${Heltec_RC32_with_display.build_src_filter} + + + +<../examples/simple_repeater> +lib_deps = + ${Heltec_RC32_with_display.lib_deps} + ${esp32_ota.lib_deps} + +[env:heltec_rc32_room_server] +extends = Heltec_RC32_with_display +build_flags = + ${Heltec_RC32_with_display.build_flags} + -D ADVERT_NAME='"Heltec RC32 Room"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D ROOM_PASSWORD='"hello"' +build_src_filter = ${Heltec_RC32_with_display.build_src_filter} + +<../examples/simple_room_server> +lib_deps = + ${Heltec_RC32_with_display.lib_deps} + ${esp32_ota.lib_deps} + +[env:heltec_rc32_terminal_chat] +extends = Heltec_RC32 +build_flags = + ${Heltec_RC32.build_flags} + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=1 +build_src_filter = ${Heltec_RC32.build_src_filter} + +<../examples/simple_secure_chat/main.cpp> +lib_deps = + ${Heltec_RC32.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:heltec_rc32_companion_radio_usb] +extends = Heltec_RC32_with_display +build_flags = + ${Heltec_RC32_with_display.build_flags} + -I examples/companion_radio/ui-new + -D UI_HAS_ROTARY_INPUT + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D ENABLE_USB_INTERFACE +build_src_filter = ${Heltec_RC32_with_display.build_src_filter} + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${Heltec_RC32_with_display.lib_deps} + densaugeo/base64 @ ~1.4.0 + end2endzone/NonBlockingRTTTL@^1.3.0 + +[env:heltec_rc32_companion_radio_ble] +extends = Heltec_RC32_with_display +build_flags = + ${Heltec_RC32_with_display.build_flags} + -I examples/companion_radio/ui-new + -D UI_HAS_ROTARY_INPUT + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D BLE_PIN_CODE=123456 + -D AUTO_SHUTDOWN_MILLIVOLTS=3400 + -D BLE_DEBUG_LOGGING=1 + -D OFFLINE_QUEUE_SIZE=256 +build_src_filter = ${Heltec_RC32_with_display.build_src_filter} + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${Heltec_RC32_with_display.lib_deps} + densaugeo/base64 @ ~1.4.0 + end2endzone/NonBlockingRTTTL@^1.3.0 + +[env:heltec_rc32_companion_radio_wifi] +extends = Heltec_RC32_with_display +build_flags = + ${Heltec_RC32_with_display.build_flags} + -I examples/companion_radio/ui-new + -D ENABLE_WIFI_INTERFACE + -D UI_HAS_ROTARY_INPUT + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D WIFI_DEBUG_LOGGING=1 + -D WIFI_SSID='"myssid"' + -D WIFI_PWD='"mypwd"' + -D OFFLINE_QUEUE_SIZE=256 +build_src_filter = ${Heltec_RC32_with_display.build_src_filter} + + + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${Heltec_RC32_with_display.lib_deps} + densaugeo/base64 @ ~1.4.0 + end2endzone/NonBlockingRTTTL@^1.3.0 + +[env:heltec_rc32_sensor] +extends = Heltec_RC32_with_display +build_flags = + ${Heltec_RC32_with_display.build_flags} + -D ADVERT_NAME='"Heltec RC32 Sensor"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D ENV_PIN_SDA=21 + -D ENV_PIN_SCL=18 +build_src_filter = ${Heltec_RC32_with_display.build_src_filter} + +<../examples/simple_sensor> +lib_deps = + ${Heltec_RC32_with_display.lib_deps} + ${esp32_ota.lib_deps} + +[env:heltec_rc32_kiss_modem] +extends = Heltec_RC32 +build_src_filter = ${Heltec_RC32.build_src_filter} + +<../examples/kiss_modem/> + +[Heltec_E290_base] +extends = esp32_base +board = heltec_e290 +build_flags = + ${esp32_base.build_flags} + -I variants/heltec_e290 + -D Vision_Master_E290 + -D ARDUINO_USB_CDC_ON_BOOT=1 + -D USE_SX1262 + -D RADIO_CLASS=CustomSX1262 + -D WRAPPER_CLASS=CustomSX1262Wrapper + -D LORA_TX_POWER=22 + -D P_LORA_DIO_1=14 + -D P_LORA_NSS=8 + -D P_LORA_RESET=12 + -D P_LORA_BUSY=13 + -D P_LORA_SCLK=9 + -D P_LORA_MISO=11 + -D P_LORA_MOSI=10 + -D P_LORA_TX_LED=45 + -D PIN_USER_BTN=0 + -D PIN_VEXT_EN=18 + -D PIN_VEXT_EN_ACTIVE=HIGH + -D PIN_VBAT_READ=7 + -D PIN_ADC_CTRL=46 + -D SX126X_DIO2_AS_RF_SWITCH=true + -D SX126X_DIO3_TCXO_VOLTAGE=1.8 + -D SX126X_CURRENT_LIMIT=140 + -D SX126X_RX_BOOSTED_GAIN=1 + -D PIN_BOARD_SDA=39 + -D PIN_BOARD_SCL=38 +build_src_filter = ${esp32_base.build_src_filter} + +<../variants/heltec_e290> +lib_deps = + ${esp32_base.lib_deps} + https://github.com/Quency-D/heltec-eink-modules/archive/563dd41fd850a1bc3039b8723da4f3a20fe1c800.zip + +[env:Heltec_E290_companion_ble] +extends = Heltec_E290_base +build_flags = + ${Heltec_E290_base.build_flags} + -I examples/companion_radio/ui-new + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D DISPLAY_CLASS=E290Display + -D AUTO_OFF_MILLIS=0 + -D BLE_PIN_CODE=123456 + -D BLE_DEBUG_LOGGING=1 + -D OFFLINE_QUEUE_SIZE=256 +build_src_filter = ${Heltec_E290_base.build_src_filter} + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${Heltec_E290_base.lib_deps} + densaugeo/base64 @ ~1.4.0 + bakercp/CRC32 @ ^2.0.0 + +[env:Heltec_E290_companion_usb] +extends = Heltec_E290_base +build_flags = + ${Heltec_E290_base.build_flags} + -I examples/companion_radio/ui-new + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D DISPLAY_CLASS=E290Display + -D AUTO_OFF_MILLIS=0 + -D BLE_DEBUG_LOGGING=1 + -D OFFLINE_QUEUE_SIZE=256 +build_src_filter = ${Heltec_E290_base.build_src_filter} + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${Heltec_E290_base.lib_deps} + densaugeo/base64 @ ~1.4.0 + bakercp/CRC32 @ ^2.0.0 + +[env:Heltec_E290_repeater] +extends = Heltec_E290_base +build_flags = + ${Heltec_E290_base.build_flags} + -D DISPLAY_CLASS=E290Display + -D ADVERT_NAME='"Heltec E290 Repeater"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 +build_src_filter = ${Heltec_E290_base.build_src_filter} + + + +<../examples/simple_repeater> +lib_deps = + ${Heltec_E290_base.lib_deps} + ${esp32_ota.lib_deps} + bakercp/CRC32 @ ^2.0.0 + +[env:Heltec_E290_repeater_bridge_espnow] +extends = Heltec_E290_base +build_flags = + ${Heltec_E290_base.build_flags} + -D DISPLAY_CLASS=E290Display + -D ADVERT_NAME='"ESPNow Bridge"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 + -D WITH_ESPNOW_BRIDGE=1 +build_src_filter = ${Heltec_E290_base.build_src_filter} + + + + + +<../examples/simple_repeater> +lib_deps = + ${Heltec_E290_base.lib_deps} + ${esp32_ota.lib_deps} + bakercp/CRC32 @ ^2.0.0 + +[env:Heltec_E290_room_server] +extends = Heltec_E290_base +build_flags = + ${Heltec_E290_base.build_flags} + -D DISPLAY_CLASS=E290Display + -D ADVERT_NAME='"Heltec E290 Room"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D ROOM_PASSWORD='"hello"' +build_src_filter = ${Heltec_E290_base.build_src_filter} + + + +<../examples/simple_room_server> +lib_deps = + ${Heltec_E290_base.lib_deps} + ${esp32_ota.lib_deps} + bakercp/CRC32 @ ^2.0.0 + +[env:Heltec_E290_kiss_modem] +extends = Heltec_E290_base +build_src_filter = ${Heltec_E290_base.build_src_filter} + +<../examples/kiss_modem/> + +[ThinkNode_M8] +extends = nrf52_base +board = thinknode_m8 +board_build.ldscript = boards/nrf52840_s140_v6.ld +build_flags = ${nrf52_base.build_flags} + -I src/helpers/nrf52 + -I lib/nrf52/s140_nrf52_6.1.1_API/include + -I lib/nrf52/s140_nrf52_6.1.1_API/include/nrf52 + -I variants/thinknode_m8 + -D THINKNODE_M8=1 + -D RADIO_CLASS=CustomSX1262 + -D WRAPPER_CLASS=CustomSX1262Wrapper + -D P_LORA_DIO_1=25 + -D P_LORA_DIO_2=32 + -D P_LORA_NSS=21 + -D P_LORA_RESET=24 + -D P_LORA_BUSY=32 + -D P_LORA_SCLK=19 + -D P_LORA_MISO=22 + -D P_LORA_MOSI=20 + -D DISPLAY_ROTATION=4 + -D UI_HAS_ROTARY_INPUT=1 + -D UI_HAS_NAV_INPUT=1 + -D UI_RECENT_LIST_SIZE=9 + -D UI_MSG_PREVIEW_SIZE=165 + -D EINK_MAX_PARTIAL_REFRESH=60 + -D AUTO_OFF_MILLIS=900000 + -D BACKLIGHT_BTN=PIN_BUTTON2 + -D UI_SHOW_CLOCK=1 + -D EINK_SCREENOFF_BLANK + -D EINK_DISPLAY_MODEL=GxEPD2_154_D67 + -D EINK_SCALE_X=1.5625f + -D EINK_SCALE_Y=1.5625f + -D EINK_X_OFFSET=0 + -D EINK_Y_OFFSET=10 + -D DISABLE_DIAGNOSTIC_OUTPUT + -D SX126X_POWER_EN=37 + -D SX126X_DIO2_AS_RF_SWITCH=true + -D SX126X_DIO3_TCXO_VOLTAGE=3.3 + -D SX126X_CURRENT_LIMIT=140 + -D SX126X_RX_BOOSTED_GAIN=1 + -D LORA_TX_POWER=22 +build_src_filter = ${nrf52_base.build_src_filter} + + + + + + + +<../variants/thinknode_m8> +lib_deps = + ${nrf52_base.lib_deps} + stevemarple/MicroNMEA @ ^2.0.6 +debug_tool = jlink +upload_protocol = nrfutil + +[env:ThinkNode_M8_repeater] +extends = ThinkNode_M8 +build_flags = + ${ThinkNode_M8.build_flags} + -D ADVERT_NAME='"ThinkNode Repeater"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 +build_src_filter = ${ThinkNode_M8.build_src_filter} + +<../examples/simple_repeater/*.cpp> +lib_deps = + ${ThinkNode_M8.lib_deps} + +[env:ThinkNode_M8_room_server] +extends = ThinkNode_M8 +build_flags = + ${ThinkNode_M8.build_flags} + -D ADVERT_NAME='"ThinkNode Room"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D ROOM_PASSWORD='"hello"' +build_src_filter = ${ThinkNode_M8.build_src_filter} + +<../examples/simple_room_server/*.cpp> +lib_deps = + ${ThinkNode_M8.lib_deps} + +[env:ThinkNode_M8_companion_radio_ble] +extends = ThinkNode_M8 +board_build.ldscript = boards/nrf52840_s140_v6_extrafs.ld +board_upload.maximum_size = 712704 +build_flags = + ${ThinkNode_M8.build_flags} + -I src/helpers/ui + -I examples/companion_radio/ui-new + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D BLE_PIN_CODE=123456 + -D DISPLAY_CLASS=GxEPDDisplay + -D OFFLINE_QUEUE_SIZE=256 + -D PIN_BUZZER=33 + -D AUTO_SHUTDOWN_MILLIVOLTS=3300 + -D QSPIFLASH=1 + -D ENV_INCLUDE_GPS=1 + -D MESH_DEBUG=1 +build_src_filter = ${ThinkNode_M8.build_src_filter} + + + + + + + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${ThinkNode_M8.lib_deps} + densaugeo/base64 @ ~1.4.0 + zinggjm/GxEPD2 @ 1.6.9 + bakercp/CRC32 @ ^2.0.0 + end2endzone/NonBlockingRTTTL@^1.3.0 + +[env:ThinkNode_M8_companion_radio_usb] +extends = ThinkNode_M8 +board_build.ldscript = boards/nrf52840_s140_v6_extrafs.ld +board_upload.maximum_size = 712704 +build_flags = + ${ThinkNode_M8.build_flags} + -I src/helpers/ui + -I examples/companion_radio/ui-new + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D DISPLAY_ROTATION=4 + -D QSPIFLASH=1 + -D DISPLAY_CLASS=GxEPDDisplay + -D OFFLINE_QUEUE_SIZE=256 + -D PIN_BUZZER=6 + -D AUTO_SHUTDOWN_MILLIVOLTS=3300 + -D ENABLE_USB_INTERFACE +build_src_filter = ${ThinkNode_M8.build_src_filter} + + + + + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${ThinkNode_M8.lib_deps} + densaugeo/base64 @ ~1.4.0 + zinggjm/GxEPD2 @ 1.6.2 + bakercp/CRC32 @ ^2.0.0 + end2endzone/NonBlockingRTTTL@^1.3.0 + +[env:ThinkNode_M8_kiss_modem] +extends = ThinkNode_M8 +build_src_filter = ${ThinkNode_M8.build_src_filter} + +<../examples/kiss_modem/> + +[LilyGo_TBeam_SX1276] +extends = esp32_base +board = ttgo-t-beam +build_flags = + ${esp32_base.build_flags} + -I variants/lilygo_tbeam_SX1276 + -D TBEAM_SX1276 + -D P_LORA_DIO_0=26 + -D P_LORA_DIO_1=33 + -D P_LORA_NSS=18 + -D P_LORA_RESET=23 + -D P_LORA_SCLK=5 + -D P_LORA_MISO=19 + -D P_LORA_MOSI=27 + -D SX127X_CURRENT_LIMIT=120 + -D RADIO_CLASS=CustomSX1276 + -D WRAPPER_CLASS=CustomSX1276Wrapper + -D DISPLAY_CLASS=SSD1306Display + -D LORA_TX_POWER=20 + -D P_LORA_TX_LED=4 + -D PIN_BOARD_SDA=21 + -D PIN_BOARD_SCL=22 + -D PIN_GPS_RX=12 + -D PIN_GPS_TX=34 + -D PIN_USER_BTN=38 + -D ENV_INCLUDE_GPS=1 +build_src_filter = ${esp32_base.build_src_filter} + +<../variants/lilygo_tbeam_SX1276> + + + + + + +board_build.partitions = min_spiffs.csv +lib_deps = + ${esp32_base.lib_deps} + lewisxhe/XPowersLib@^0.2.7 + adafruit/Adafruit SSD1306 @ ^2.5.13 + stevemarple/MicroNMEA @ ^2.0.6 + boschsensortec/BSEC Software Library @ ^1.8.1492 + +[env:Tbeam_SX1276_companion_radio_ble] +extends = LilyGo_TBeam_SX1276 +board_build.upload.maximum_ram_size = 2000000 +build_flags = + ${LilyGo_TBeam_SX1276.build_flags} + -I examples/companion_radio/ui-new + -D MAX_CONTACTS=160 + -D MAX_GROUP_CHANNELS=40 + -D BLE_PIN_CODE=123456 + -D OFFLINE_QUEUE_SIZE=128 +build_src_filter = ${LilyGo_TBeam_SX1276.build_src_filter} + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${LilyGo_TBeam_SX1276.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:Tbeam_SX1276_repeater] +extends = LilyGo_TBeam_SX1276 +build_flags = + ${LilyGo_TBeam_SX1276.build_flags} + -D ADVERT_NAME='"Tbeam Repeater"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 + -D PERSISTANT_GPS=1 +build_src_filter = ${LilyGo_TBeam_SX1276.build_src_filter} + +<../examples/simple_repeater> +lib_deps = + ${LilyGo_TBeam_SX1276.lib_deps} + ${esp32_ota.lib_deps} + +[env:Tbeam_SX1276_repeater_bridge_espnow] +extends = LilyGo_TBeam_SX1276 +build_flags = + ${LilyGo_TBeam_SX1276.build_flags} + -D ADVERT_NAME='"ESPNow Bridge"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 + -D PERSISTANT_GPS=1 + -D WITH_ESPNOW_BRIDGE=1 +build_src_filter = ${LilyGo_TBeam_SX1276.build_src_filter} + + + +<../examples/simple_repeater> +lib_deps = + ${LilyGo_TBeam_SX1276.lib_deps} + ${esp32_ota.lib_deps} + +[env:Tbeam_SX1276_room_server] +extends = LilyGo_TBeam_SX1276 +build_flags = + ${LilyGo_TBeam_SX1276.build_flags} + -D ADVERT_NAME='"Tbeam Room"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' +build_src_filter = ${LilyGo_TBeam_SX1276.build_src_filter} + +<../examples/simple_room_server> +lib_deps = + ${LilyGo_TBeam_SX1276.lib_deps} + ${esp32_ota.lib_deps} + +[env:Tbeam_SX1276_kiss_modem] +extends = LilyGo_TBeam_SX1276 +build_src_filter = ${LilyGo_TBeam_SX1276.build_src_filter} + +<../examples/kiss_modem/> + +[ThinkNode_M6] +extends = nrf52_base +board = thinknode_m6 +board_build.ldscript = boards/nrf52840_s140_v6.ld +build_flags = ${nrf52_base.build_flags} + ${sensor_base.build_flags} + -I src/helpers/nrf52 + -I lib/nrf52/s140_nrf52_6.1.1_API/include + -I lib/nrf52/s140_nrf52_6.1.1_API/include/nrf52 + -I variants/thinknode_m6 + -D THINKNODE_M6=1 + -D USE_SX1262 + -D RADIO_CLASS=CustomSX1262 + -D WRAPPER_CLASS=CustomSX1262Wrapper + -D P_LORA_DIO_1=38 + -D P_LORA_NSS=44 + -D P_LORA_RESET=42 + -D P_LORA_BUSY=43 + -D P_LORA_SCLK=45 + -D P_LORA_MISO=47 + -D P_LORA_MOSI=46 + -D SX126X_DIO2_AS_RF_SWITCH=true + -D SX126X_DIO3_TCXO_VOLTAGE=3.3 + -D SX126X_CURRENT_LIMIT=140 + -D SX126X_RX_BOOSTED_GAIN=1 + -D LORA_TX_POWER=22 + -D P_LORA_TX_LED=PIN_LED_BLUE +build_src_filter = ${nrf52_base.build_src_filter} + + + + + + + +<../variants/thinknode_m6> +lib_deps = + ${nrf52_base.lib_deps} + ${sensor_base.lib_deps} +debug_tool = jlink +upload_protocol = nrfutil + +[env:ThinkNode_M6_repeater] +extends = ThinkNode_M6 +build_flags = + ${ThinkNode_M6.build_flags} + -D ADVERT_NAME='"ThinkNode Repeater"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 +build_src_filter = ${ThinkNode_M6.build_src_filter} + +<../examples/simple_repeater/*.cpp> +lib_deps = + ${ThinkNode_M6.lib_deps} + +[env:ThinkNode_M6_room_server] +extends = ThinkNode_M6 +build_flags = + ${ThinkNode_M6.build_flags} + -D ADVERT_NAME='"ThinkNode Room"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D ROOM_PASSWORD='"hello"' +build_src_filter = ${ThinkNode_M6.build_src_filter} + +<../examples/simple_room_server/*.cpp> +lib_deps = + ${ThinkNode_M6.lib_deps} + +[env:ThinkNode_M6_companion_radio_ble] +extends = ThinkNode_M6 +board_build.ldscript = boards/nrf52840_s140_v6_extrafs.ld +board_upload.maximum_size = 712704 +build_flags = + ${ThinkNode_M6.build_flags} + -I src/helpers/ui + -I examples/companion_radio/ui-new + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D BLE_PIN_CODE=123456 + -D BLE_DEBUG_LOGGING=1 + -D OFFLINE_QUEUE_SIZE=256 + -D AUTO_SHUTDOWN_MILLIVOLTS=3300 +build_src_filter = ${ThinkNode_M6.build_src_filter} + + + + + +<../examples/companion_radio/*.cpp> +lib_deps = + ${ThinkNode_M6.lib_deps} + densaugeo/base64 @ ~1.4.0 + end2endzone/NonBlockingRTTTL@^1.3.0 + +[env:ThinkNode_M6_companion_radio_usb] +extends = ThinkNode_M6 +board_build.ldscript = boards/nrf52840_s140_v6_extrafs.ld +board_upload.maximum_size = 712704 +build_flags = + ${ThinkNode_M6.build_flags} + -I src/helpers/ui + -I examples/companion_radio/ui-new + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D OFFLINE_QUEUE_SIZE=256 + -D AUTO_SHUTDOWN_MILLIVOLTS=3300 + -D ENABLE_USB_INTERFACE +build_src_filter = ${ThinkNode_M6.build_src_filter} + + + + + +<../examples/companion_radio/*.cpp> +lib_deps = + ${ThinkNode_M6.lib_deps} + densaugeo/base64 @ ~1.4.0 + end2endzone/NonBlockingRTTTL@^1.3.0 + +[env:ThinkNode_M6_kiss_modem] +extends = ThinkNode_M6 +build_src_filter = ${ThinkNode_M6.build_src_filter} + +<../examples/kiss_modem/> + +[Tiny_Relay] +extends = stm32_base +board = tiny_relay +board_upload.maximum_size = 229376 +build_flags = ${stm32_base.build_flags} + -D RADIO_CLASS=CustomSTM32WLx + -D WRAPPER_CLASS=CustomSTM32WLxWrapper + -D SPI_INTERFACES_COUNT=0 + -D RX_BOOSTED_GAIN=true + -D LORA_TX_POWER=22 + -D MAX_LORA_TX_POWER=22 + -I variants/tiny_relay +build_src_filter = ${stm32_base.build_src_filter} + +<../variants/tiny_relay> + +[env:Tiny_Relay_repeater] +extends = Tiny_Relay +build_flags = ${Tiny_Relay.build_flags} + -D ADVERT_NAME='"tiny_relay Repeater"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 +build_src_filter = ${Tiny_Relay.build_src_filter} + +<../examples/simple_repeater> + +[env:Tiny_Relay_sensor] +extends = Tiny_Relay +build_flags = ${Tiny_Relay.build_flags} + -D ADVERT_NAME='"tiny_relay Sensor"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 +build_src_filter = ${Tiny_Relay.build_src_filter} + +<../examples/simple_sensor> + +[env:Tiny_Relay_companion_radio_usb] +extends = Tiny_Relay +build_flags = ${Tiny_Relay.build_flags} + -D MAX_CONTACTS=100 + -D MAX_GROUP_CHANNELS=8 + -D MAX_LORA_TX_POWER=22 + -D ENABLE_USB_INTERFACE +build_src_filter = ${Tiny_Relay.build_src_filter} + +<../examples/companion_radio/*.cpp> +lib_deps = ${Tiny_Relay.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:Tiny_Relay_kiss_modem] +extends = Tiny_Relay +build_src_filter = ${Tiny_Relay.build_src_filter} + +<../examples/kiss_modem/> + +[me25ls01] +extends = nrf52_base +board = minewsemi_me25ls01 +board_build.ldscript = boards/nrf52840_s140_v7.ld +build_flags = ${nrf52_base.build_flags} + -I src/helpers/nrf52 + -I lib/nrf52/s140_nrf52_7.3.0_API/include + -I lib/nrf52/s140_nrf52_7.3.0_API/include/nrf52 + -I variants/minewsemi_me25ls01 + -D me25ls01 + -D PIN_USER_BTN=27 + -D PIN_STATUS_LED=39 + -D P_LORA_TX_LED=22 + -D RADIO_CLASS=CustomLR1110 + -D WRAPPER_CLASS=CustomLR1110Wrapper + -D LORA_TX_POWER=22 + -D ENV_INCLUDE_GPS=0 + -D ENV_INCLUDE_AHTX0=1 + -D ENV_INCLUDE_BME280=1 + -D ENV_INCLUDE_INA3221=1 + -D ENV_INCLUDE_INA219=1 +build_src_filter = ${nrf52_base.build_src_filter} + + + + + +<../variants/minewsemi_me25ls01> + + +debug_tool = jlink +upload_protocol = nrfutil +lib_deps = ${nrf52_base.lib_deps} + adafruit/RTClib @ ^2.1.3 + densaugeo/base64 @ ~1.4.0 + stevemarple/MicroNMEA @ ^2.0.6 + end2endzone/NonBlockingRTTTL@^1.3.0 + adafruit/Adafruit SSD1306 @ ^2.5.13 + adafruit/Adafruit INA3221 Library @ ^1.0.1 + adafruit/Adafruit INA219 @ ^1.2.3 + adafruit/Adafruit AHTX0 @ ^2.0.5 + adafruit/Adafruit BME280 Library @ ^2.3.0 + +[env:Minewsemi_me25ls01_companion_radio_ble] +extends = me25ls01 +board_build.ldscript = boards/nrf52840_s140_v7_extrafs.ld +board_upload.maximum_size = 708608 +build_flags = ${me25ls01.build_flags} + -I examples/companion_radio/ui-orig + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D BLE_PIN_CODE=123456 + -D OFFLINE_QUEUE_SIZE=256 + -D RX_BOOSTED_GAIN=true + -D RF_SWITCH_TABLE + -D DISPLAY_CLASS=NullDisplayDriver +build_src_filter = ${me25ls01.build_src_filter} + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-orig/*.cpp> + +[env:Minewsemi_me25ls01_repeater] +extends = me25ls01 +build_flags = ${me25ls01.build_flags} + -D OFFLINE_QUEUE_SIZE=256 + -D RX_BOOSTED_GAIN=true + -D RF_SWITCH_TABLE + -D ADVERT_NAME='"ME25LS01 Repeater"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 + -D DISPLAY_CLASS=NullDisplayDriver +build_src_filter = ${me25ls01.build_src_filter} + +<../examples/simple_repeater> + + + +[env:Minewsemi_me25ls01_room_server] +extends = me25ls01 +build_flags = ${me25ls01.build_flags} + -D OFFLINE_QUEUE_SIZE=256 + -D RX_BOOSTED_GAIN=true + -D RF_SWITCH_TABLE + -D ADVERT_NAME='"ME25LS01 Room"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D ROOM_PASSWORD='"hello"' + -D MAX_NEIGHBOURS=50 + -D DISPLAY_CLASS=NullDisplayDriver +build_src_filter = ${me25ls01.build_src_filter} + +<../examples/simple_room_server> + +[env:Minewsemi_me25ls01_terminal_chat] +extends = me25ls01 +build_flags = ${me25ls01.build_flags} + -D OFFLINE_QUEUE_SIZE=256 + -D RX_BOOSTED_GAIN=true + -D RF_SWITCH_TABLE + -D ADVERT_NAME='"ME25LS01 Chat"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D ROOM_PASSWORD='"hello"' + -D MAX_NEIGHBOURS=50 + -D DISPLAY_CLASS=NullDisplayDriver +build_src_filter = ${me25ls01.build_src_filter} + +<../examples/simple_secure_chat/main.cpp> + +[env:Minewsemi_me25ls01_companion_radio_usb] +extends = me25ls01 +board_build.ldscript = boards/nrf52840_s140_v7_extrafs.ld +board_upload.maximum_size = 708608 +build_flags = ${me25ls01.build_flags} + -I examples/companion_radio/ui-orig + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D OFFLINE_QUEUE_SIZE=256 + -D RX_BOOSTED_GAIN=true + -D RF_SWITCH_TABLE + -D DISPLAY_CLASS=NullDisplayDriver + -D ENABLE_USB_INTERFACE +build_src_filter = ${me25ls01.build_src_filter} + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-orig/*.cpp> + +[env:Minewsemi_me25ls01_kiss_modem] +extends = me25ls01 +build_src_filter = ${me25ls01.build_src_filter} + +<../examples/kiss_modem/> + +[ThinkNode_M1] +extends = nrf52_base +board = thinknode_m1 +board_build.ldscript = boards/nrf52840_s140_v6.ld +build_flags = ${nrf52_base.build_flags} + -I src/helpers/nrf52 + -I lib/nrf52/s140_nrf52_6.1.1_API/include + -I lib/nrf52/s140_nrf52_6.1.1_API/include/nrf52 + -I variants/thinknode_m1 + -D THINKNODE_M1=1 + -D RADIO_CLASS=CustomSX1262 + -D WRAPPER_CLASS=CustomSX1262Wrapper + -D P_LORA_DIO_1=20 + -D P_LORA_NSS=24 + -D P_LORA_RESET=25 + -D P_LORA_BUSY=17 + -D P_LORA_SCLK=19 + -D P_LORA_MISO=23 + -D P_LORA_MOSI=22 + -D SX126X_POWER_EN=37 + -D SX126X_DIO2_AS_RF_SWITCH=true + -D SX126X_DIO3_TCXO_VOLTAGE=1.8 + -D SX126X_CURRENT_LIMIT=140 + -D SX126X_RX_BOOSTED_GAIN=1 + -D LORA_TX_POWER=22 + -D P_LORA_TX_LED=13 + -D UI_RECENT_LIST_SIZE=9 + -D UI_MSG_PREVIEW_SIZE=165 + -D EINK_MAX_PARTIAL_REFRESH=60 + -D EINK_DISPLAY_MODEL=GxEPD2_154_D67 + -D EINK_SCALE_X=1.5625f + -D EINK_SCALE_Y=1.5625f + -D EINK_X_OFFSET=0 + -D EINK_Y_OFFSET=10 + -D BACKLIGHT_BTN=PIN_BUTTON2 + -D AUTO_OFF_MILLIS=900000 + -D UI_NO_HIBERNATE + -D DISABLE_DIAGNOSTIC_OUTPUT +build_src_filter = ${nrf52_base.build_src_filter} + + + + + +<../variants/thinknode_m1> +lib_deps = + ${nrf52_base.lib_deps} + stevemarple/MicroNMEA @ ^2.0.6 +debug_tool = jlink +upload_protocol = nrfutil + +[env:ThinkNode_M1_repeater] +extends = ThinkNode_M1 +build_flags = + ${ThinkNode_M1.build_flags} + -D ADVERT_NAME='"ThinkNode Repeater"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 +build_src_filter = ${ThinkNode_M1.build_src_filter} + +<../examples/simple_repeater/*.cpp> +lib_deps = + ${ThinkNode_M1.lib_deps} + +[env:ThinkNode_M1_room_server] +extends = ThinkNode_M1 +build_flags = + ${ThinkNode_M1.build_flags} + -D ADVERT_NAME='"ThinkNode Room"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D ROOM_PASSWORD='"hello"' +build_src_filter = ${ThinkNode_M1.build_src_filter} + +<../examples/simple_room_server/*.cpp> +lib_deps = + ${ThinkNode_M1.lib_deps} + +[env:ThinkNode_M1_companion_radio_ble] +extends = ThinkNode_M1 +board_build.ldscript = boards/nrf52840_s140_v6_extrafs.ld +board_upload.maximum_size = 712704 +build_flags = + ${ThinkNode_M1.build_flags} + -I src/helpers/ui + -I examples/companion_radio/ui-new + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D BLE_PIN_CODE=123456 + -D BLE_DEBUG_LOGGING=1 + -D DISPLAY_ROTATION=4 + -D DISPLAY_CLASS=GxEPDDisplay + -D OFFLINE_QUEUE_SIZE=256 + -D PIN_BUZZER=6 + -D AUTO_SHUTDOWN_MILLIVOLTS=3300 + -D QSPIFLASH=1 + -D ENV_INCLUDE_GPS=1 +build_src_filter = ${ThinkNode_M1.build_src_filter} + + + + + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${ThinkNode_M1.lib_deps} + densaugeo/base64 @ ~1.4.0 + zinggjm/GxEPD2 @ 1.6.2 + bakercp/CRC32 @ ^2.0.0 + end2endzone/NonBlockingRTTTL@^1.3.0 + +[env:ThinkNode_M1_companion_radio_usb] +extends = ThinkNode_M1 +board_build.ldscript = boards/nrf52840_s140_v6_extrafs.ld +board_upload.maximum_size = 712704 +build_flags = + ${ThinkNode_M1.build_flags} + -I src/helpers/ui + -I examples/companion_radio/ui-new + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D DISPLAY_ROTATION=4 + -D QSPIFLASH=1 + -D DISPLAY_CLASS=GxEPDDisplay + -D OFFLINE_QUEUE_SIZE=256 + -D PIN_BUZZER=6 + -D AUTO_SHUTDOWN_MILLIVOLTS=3300 + -D ENABLE_USB_INTERFACE +build_src_filter = ${ThinkNode_M1.build_src_filter} + + + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${ThinkNode_M1.lib_deps} + densaugeo/base64 @ ~1.4.0 + zinggjm/GxEPD2 @ 1.6.2 + bakercp/CRC32 @ ^2.0.0 + end2endzone/NonBlockingRTTTL@^1.3.0 + +[env:ThinkNode_M1_kiss_modem] +extends = ThinkNode_M1 +build_src_filter = ${ThinkNode_M1.build_src_filter} + +<../examples/kiss_modem/> + +[Xiao_rp2040] +extends = rp2040_base +board = seeed_xiao_rp2040 +board_build.filesystem_size = 0.5m +build_flags = ${rp2040_base.build_flags} + -I variants/xiao_rp2040 + -D SX126X_CURRENT_LIMIT=140 + -D USE_SX1262 + -D RADIO_CLASS=CustomSX1262 + -D WRAPPER_CLASS=CustomSX1262Wrapper + -D P_LORA_DIO_1=27 + -D P_LORA_NSS=6 + -D P_LORA_RESET=28 + -D P_LORA_BUSY=29 + -D P_LORA_TX_LED=17 + -D SX126X_RXEN=7 + -D SX126X_TXEN=RADIOLIB_NC + -D SX126X_DIO2_AS_RF_SWITCH=true + -D SX126X_DIO3_TCXO_VOLTAGE=1.8 + -D SX126X_RX_BOOSTED_GAIN=1 + -D LORA_TX_POWER=22 +build_src_filter = ${rp2040_base.build_src_filter} + + + +<../variants/xiao_rp2040> +lib_deps = ${rp2040_base.lib_deps} + +[env:Xiao_rp2040_repeater] +extends = Xiao_rp2040 +build_flags = ${Xiao_rp2040.build_flags} + -D ADVERT_NAME='"Xiao Repeater"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 +build_src_filter = ${Xiao_rp2040.build_src_filter} + +<../examples/simple_repeater> + +[env:Xiao_rp2040_room_server] +extends = Xiao_rp2040 +build_flags = ${Xiao_rp2040.build_flags} + -D ADVERT_NAME='"Xiao Room"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D ROOM_PASSWORD='"hello"' +build_src_filter = ${Xiao_rp2040.build_src_filter} + +<../examples/simple_room_server> + +[env:Xiao_rp2040_companion_radio_usb] +extends = Xiao_rp2040 +build_flags = ${Xiao_rp2040.build_flags} + -D MAX_CONTACTS=100 + -D MAX_GROUP_CHANNELS=8 + -D ENABLE_USB_INTERFACE +build_src_filter = ${Xiao_rp2040.build_src_filter} + +<../examples/companion_radio/*.cpp> +lib_deps = ${Xiao_rp2040.lib_deps} + densaugeo/base64 @ ~1.4.0 +lib_ignore = BLE + +[env:Xiao_rp2040_terminal_chat] +extends = Xiao_rp2040 +build_flags = ${Xiao_rp2040.build_flags} + -D MAX_CONTACTS=100 + -D MAX_GROUP_CHANNELS=1 +build_src_filter = ${Xiao_rp2040.build_src_filter} + +<../examples/simple_secure_chat/main.cpp> +lib_deps = ${Xiao_rp2040.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:Xiao_rp2040_kiss_modem] +extends = Xiao_rp2040 +build_src_filter = ${Xiao_rp2040.build_src_filter} + +<../examples/kiss_modem/> + +[ThinkNode_M7] +extends = esp32_base +board = thinknode_m7 +board_upload.flash_size = 8MB +board_build.partitions = default_8MB.csv +build_flags = ${esp32_base.build_flags} + -I src/helpers/esp32 + -I variants/thinknode_m7 + -I src/helpers/sensors + -I src/helpers/ui + -D THINKNODE_M7 + -D PIN_USER_BTN_ANA=4 + -D PIN_STATUS_LED=3 + -D LED_STATE_ON=LOW + -D RADIO_CLASS=CustomLR1110 + -D WRAPPER_CLASS=CustomLR1110Wrapper + -D USE_LR1110 + -D LORA_TX_POWER=22 + -D RF_SWITCH_TABLE + -D RX_BOOSTED_GAIN=true + -D P_LORA_BUSY=13 + -D P_LORA_SCLK=11 + -D P_LORA_NSS=12 + -D P_LORA_DIO_1=38 + -D P_LORA_MISO=9 + -D P_LORA_MOSI=10 + -D P_LORA_RESET=39 + -D P_LORA_TX_LED=46 + -D LR11X0_DIO_AS_RF_SWITCH=true + -D LR11X0_DIO3_TCXO_VOLTAGE=1.8 +build_src_filter = ${esp32_base.build_src_filter} + + + + + + + +<../variants/thinknode_m7> +lib_deps = ${esp32_base.lib_deps} + stevemarple/MicroNMEA @ ^2.0.6 + +[ThinkNode_M7_ethernet] +build_flags = + -D ETHERNET_ENABLED + -D ETHERNET_USE_CH390 + -D ETHERNET_CLASS=CH390EthernetInterface + -D ETH_MISO_PIN=14 + -D ETH_MOSI_PIN=48 + -D ETH_SCLK_PIN=47 + -D ETH_CS_PIN=21 + -D ETH_INT_PIN=45 + -D ETHERNET_DEBUG_LOGGING=1 +build_src_filter = + + + + +lib_deps = + https://github.com/liamcottle/ESP32-CH390.git#47b401f1de546118b03c18b5689dedec45871f2d + +[env:ThinkNode_M7_repeater] +extends = ThinkNode_M7 +build_src_filter = ${ThinkNode_M7.build_src_filter} + +<../examples/simple_repeater/*.cpp> +build_flags = + ${ThinkNode_M7.build_flags} + -D ADVERT_NAME='"ThinkNode M7 Repeater"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 +lib_deps = + ${ThinkNode_M7.lib_deps} + ${esp32_ota.lib_deps} + +[env:ThinkNode_M7_room_server] +extends = ThinkNode_M7 +build_src_filter = ${ThinkNode_M7.build_src_filter} + +<../examples/simple_room_server> +build_flags = + ${ThinkNode_M7.build_flags} + -D ADVERT_NAME='"ThinkNode M7 Room Server"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D ROOM_PASSWORD='"hello"' +lib_deps = + ${ThinkNode_M7.lib_deps} + ${esp32_ota.lib_deps} + +[env:ThinkNode_M7_companion_radio_ble] +extends = ThinkNode_M7 +build_flags = + ${ThinkNode_M7.build_flags} + ${ThinkNode_M7_ethernet.build_flags} + -I examples/companion_radio/ui-orig + -D DISPLAY_CLASS=NullDisplayDriver + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D BLE_PIN_CODE=123456 + -D OFFLINE_QUEUE_SIZE=256 + -D ENABLE_WIFI_INTERFACE +build_src_filter = ${ThinkNode_M7.build_src_filter} + ${ThinkNode_M7_ethernet.build_src_filter} + + + + + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-orig/*.cpp> +lib_deps = + ${ThinkNode_M7.lib_deps} + ${ThinkNode_M7_ethernet.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:ThinkNode_M7_companion_radio_usb] +extends = ThinkNode_M7 +build_flags = + ${ThinkNode_M7.build_flags} + -I examples/companion_radio/ui-orig + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D OFFLINE_QUEUE_SIZE=256 + -D ENABLE_USB_INTERFACE +build_src_filter = ${ThinkNode_M7.build_src_filter} + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-orig/*.cpp> +lib_deps = + ${ThinkNode_M7.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:ThinkNode_M7_companion_radio_wifi] +extends = ThinkNode_M7 +build_flags = + ${ThinkNode_M7.build_flags} + -I examples/companion_radio/ui-orig + -D ENABLE_WIFI_INTERFACE + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D DISPLAY_CLASS=NullDisplayDriver + -D WIFI_DEBUG_LOGGING=1 + -D WIFI_SSID='"myssid"' + -D WIFI_PWD='"mypwd"' + -D OFFLINE_QUEUE_SIZE=256 +build_src_filter = ${ThinkNode_M7.build_src_filter} + + + + + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-orig/*.cpp> +lib_deps = + ${ThinkNode_M7.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:ThinkNode_M7_companion_radio_ethernet] +extends = ThinkNode_M7 +build_flags = + ${ThinkNode_M7.build_flags} + ${ThinkNode_M7_ethernet.build_flags} + -I examples/companion_radio/ui-orig + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D DISPLAY_CLASS=NullDisplayDriver + -D OFFLINE_QUEUE_SIZE=256 +build_src_filter = ${ThinkNode_M7.build_src_filter} + ${ThinkNode_M7_ethernet.build_src_filter} + + + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-orig/*.cpp> +lib_deps = ${ThinkNode_M7.lib_deps} + ${ThinkNode_M7_ethernet.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:ThinkNode_M7_kiss_modem] +extends = ThinkNode_M7 +build_src_filter = ${ThinkNode_M7.build_src_filter} + +<../examples/kiss_modem/> + +[nibble_zero_connect_base] +extends = esp32_base +board = esp32-s3-zero +build_flags = + ${esp32_base.build_flags} + -I variants/nibble_zero_connect + -D NIBBLE_ZERO_CONNECT + -D P_LORA_DIO_1=4 + -D P_LORA_NSS=10 + -D P_LORA_RESET=6 + -D P_LORA_BUSY=5 + -D P_LORA_SCLK=12 + -D P_LORA_MISO=13 + -D P_LORA_MOSI=11 + -D PIN_USER_BTN=1 + -D PIN_BOARD_SDA=8 + -D PIN_BOARD_SCL=7 + -D PIN_STATUS_LED=39 + -D P_LORA_TX_LED=39 + -D DISPLAY_ROTATION=0 + -D SX126X_DIO2_AS_RF_SWITCH=true + -D SX126X_DIO3_TCXO_VOLTAGE=1.8 + -D SX126X_CURRENT_LIMIT=140 + -D RADIO_CLASS=CustomSX1262 + -D WRAPPER_CLASS=CustomSX1262Wrapper + -D LORA_TX_POWER=22 + -D SX126X_RX_BOOSTED_GAIN=1 +build_src_filter = ${esp32_base.build_src_filter} + +<../variants/nibble_zero_connect> +lib_deps = + ${esp32_base.lib_deps} + adafruit/Adafruit SSD1306 @ ^2.5.13 + +[env:nibble_zero_connect_repeater_] +extends = nibble_zero_connect_base +build_flags = + ${nibble_zero_connect_base.build_flags} + -D DISPLAY_CLASS=SSD1306Display + -D ADVERT_NAME='"Nibble Repeater"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 +build_src_filter = ${nibble_zero_connect_base.build_src_filter} + + + +<../examples/simple_repeater> +lib_deps = + ${nibble_zero_connect_base.lib_deps} + ${esp32_ota.lib_deps} + +[env:nibble_zero_connect_repeater_bridge_espnow_] +extends = nibble_zero_connect_base +build_flags = + ${nibble_zero_connect_base.build_flags} + -D DISPLAY_CLASS=SSD1306Display + -D ADVERT_NAME='"ESPNow Bridge"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 + -D WITH_ESPNOW_BRIDGE=1 +build_src_filter = ${nibble_zero_connect_base.build_src_filter} + + + + + +<../examples/simple_repeater> +lib_deps = + ${nibble_zero_connect_base.lib_deps} + ${esp32_ota.lib_deps} + +[env:nibble_zero_connect_terminal_chat_] +extends = nibble_zero_connect_base +build_flags = + ${nibble_zero_connect_base.build_flags} + -D MAX_CONTACTS=300 + -D MAX_GROUP_CHANNELS=1 +build_src_filter = ${nibble_zero_connect_base.build_src_filter} + +<../examples/simple_secure_chat/main.cpp> +lib_deps = + ${nibble_zero_connect_base.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:nibble_zero_connect_room_server_] +extends = nibble_zero_connect_base +build_flags = + ${nibble_zero_connect_base.build_flags} + -D DISPLAY_CLASS=SSD1306Display + -D ADVERT_NAME='"Nibble Room"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D ROOM_PASSWORD='"hello"' +build_src_filter = ${nibble_zero_connect_base.build_src_filter} + + + +<../examples/simple_room_server> +lib_deps = + ${nibble_zero_connect_base.lib_deps} + ${esp32_ota.lib_deps} + +[env:nibble_zero_connect_companion_radio_usb_] +extends = nibble_zero_connect_base +build_flags = + ${nibble_zero_connect_base.build_flags} + -I examples/companion_radio/ui-new + -D DISPLAY_CLASS=SSD1306Display + -D MAX_CONTACTS=300 + -D MAX_GROUP_CHANNELS=8 + -D ENABLE_USB_INTERFACE +build_src_filter = ${nibble_zero_connect_base.build_src_filter} + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${nibble_zero_connect_base.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:nibble_zero_connect_companion_radio_ble_] +extends = nibble_zero_connect_base +build_flags = + ${nibble_zero_connect_base.build_flags} + -I examples/companion_radio/ui-new + -D DISPLAY_CLASS=SSD1306Display + -D MAX_CONTACTS=300 + -D MAX_GROUP_CHANNELS=8 + -D BLE_PIN_CODE=123456 + -D BLE_DEBUG_LOGGING=1 + -D OFFLINE_QUEUE_SIZE=256 +build_src_filter = ${nibble_zero_connect_base.build_src_filter} + + + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${nibble_zero_connect_base.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:nibble_zero_connect_companion_radio_wifi_] +extends = nibble_zero_connect_base +build_flags = + ${nibble_zero_connect_base.build_flags} + -I examples/companion_radio/ui-new + -D ENABLE_WIFI_INTERFACE + -D DISPLAY_CLASS=SSD1306Display + -D MAX_CONTACTS=300 + -D MAX_GROUP_CHANNELS=8 + -D WIFI_DEBUG_LOGGING=1 + -D WIFI_SSID='"myssid"' + -D WIFI_PWD='"mypwd"' +build_src_filter = ${nibble_zero_connect_base.build_src_filter} + + + + + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${nibble_zero_connect_base.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[ThinkNode_M9] +extends = esp32_base +board = thinknode_m9 +board_check = true +board_build.partitions = default_16MB.csv +upload_protocol = esptool +build_flags = + ${esp32_base.build_flags} + ${sensor_base.build_flags} + -I variants/thinknode_m9 + -I src/helpers/esp32 + -I src/helpers/sensors + -D THINKNODE_M9 + -D PIN_BUZZER=9 + -D PIN_BOARD_SCL=6 + -D PIN_BOARD_SDA=7 + -D P_LORA_NSS=39 + -D P_LORA_RESET=45 + -D P_LORA_BUSY=41 + -D P_LORA_SCLK=40 + -D P_LORA_MISO=38 + -D P_LORA_MOSI=47 + -D P_LORA_DIO_1=42 + -D USE_LR1110 + -D RF_SWITCH_TABLE + -D RADIO_CLASS=CustomLR1110 + -D WRAPPER_CLASS=CustomLR1110Wrapper + -D LR11X0_DIO_AS_RF_SWITCH=true + -D LR11X0_DIO3_TCXO_VOLTAGE=3.3 + -D LORA_TX_POWER=22 + -D DISPLAY_CLASS=ST7789Display + -D DISPLAY_FLIP_VERTICALLY=1 + -D DISPLAY_SCALE_X=2.5f + -D DISPLAY_SCALE_Y=3.75f + -D ST7789 + -D PIN_TFT_VDD_CTL=-1 + -D PIN_TFT_LEDA_CTL=17 + -D PIN_TFT_RST=14 + -D PIN_GPS_RX=3 + -D PIN_GPS_TX=2 + -D PIN_GPS_EN=11 + -D PIN_GPS_EN_ACTIVE=LOW + -D PIN_GPS_RESET=5 + -D PIN_GPS_RESET_ACTIVE=HIGH + -D GPS_BAUD_RATE=115200 + -D ENV_INCLUDE_GPS=1 + -D PIN_VBAT_READ=13 +build_src_filter = ${esp32_base.build_src_filter} + + + + + + + + + + + +<../variants/thinknode_m9> +lib_deps = ${esp32_base.lib_deps} + ${sensor_base.lib_deps} + adafruit/Adafruit GFX Library @ ^1.12.1 + +[env:ThinkNode_M9_repeater_] +extends = ThinkNode_M9 +build_flags = + ${ThinkNode_M9.build_flags} + -D ADVERT_NAME='"ThinkNode M9 Repeater"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 +build_src_filter = ${ThinkNode_M9.build_src_filter} + +<../examples/simple_repeater/*.cpp> +lib_deps = + ${ThinkNode_M9.lib_deps} + ${esp32_ota.lib_deps} + +[env:ThinkNode_M9_room_server_] +extends = ThinkNode_M9 +build_src_filter = ${ThinkNode_M9.build_src_filter} + +<../examples/simple_room_server> +build_flags = + ${ThinkNode_M9.build_flags} + -D ADVERT_NAME='"ThinkNode M9 Room Server"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D ROOM_PASSWORD='"hello"' +lib_deps = + ${ThinkNode_M9.lib_deps} + ${esp32_ota.lib_deps} + +[env:ThinkNode_M9_companion_radio_ble_] +extends = ThinkNode_M9 +build_flags = + ${ThinkNode_M9.build_flags} + -I examples/companion_radio/ui-new + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D BLE_PIN_CODE=123456 + -D OFFLINE_QUEUE_SIZE=256 +build_src_filter = ${ThinkNode_M9.build_src_filter} + + + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${ThinkNode_M9.lib_deps} + densaugeo/base64 @ ~1.4.0 + end2endzone/NonBlockingRTTTL@^1.3.0 + +[env:ThinkNode_M9_companion_radio_usb_] +extends = ThinkNode_M9 +build_flags = + ${ThinkNode_M9.build_flags} + -I examples/companion_radio/ui-new + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D OFFLINE_QUEUE_SIZE=256 + -D ENABLE_USB_INTERFACE +build_src_filter = ${ThinkNode_M9.build_src_filter} + + + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${ThinkNode_M9.lib_deps} + densaugeo/base64 @ ~1.4.0 + end2endzone/NonBlockingRTTTL@^1.3.0 + +[env:ThinkNode_M9_companion_radio_wifi_] +extends = ThinkNode_M9 +build_flags = + ${ThinkNode_M9.build_flags} + -I examples/companion_radio/ui-new + -D ENABLE_WIFI_INTERFACE + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D WIFI_DEBUG_LOGGING=1 + -D WIFI_SSID='"myssid"' + -D WIFI_PWD='"mypwd"' + -D OFFLINE_QUEUE_SIZE=256 +build_src_filter = ${ThinkNode_M9.build_src_filter} + + + + + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${ThinkNode_M9.lib_deps} + densaugeo/base64 @ ~1.4.0 + end2endzone/NonBlockingRTTTL@^1.3.0 + +[env:ThinkNode_M9_kiss_modem] +extends = ThinkNode_M9 +build_src_filter = ${ThinkNode_M9.build_src_filter} + +<../examples/kiss_modem/> + +[ikoka_nano_nrf] +extends = nrf52_base +board = seeed-xiao-afruitnrf52-nrf52840 +board_build.ldscript = boards/nrf52840_s140_v7.ld +build_flags = ${nrf52_base.build_flags} + ${sensor_base.build_flags} + -D NRF52_PLATFORM -D XIAO_NRF52 + -I lib/nrf52/s140_nrf52_7.3.0_API/include + -I lib/nrf52/s140_nrf52_7.3.0_API/include/nrf52 + -I variants/ikoka_nano_nrf + -I src/helpers/nrf52 + -D P_LORA_TX_LED=11 + -D DISPLAY_CLASS=NullDisplayDriver + -D USE_SX1262 + -D RADIO_CLASS=CustomSX1262 + -D WRAPPER_CLASS=CustomSX1262Wrapper + -D P_LORA_DIO_1=D1 + -D P_LORA_BUSY=D2 + -D P_LORA_RESET=D3 + -D P_LORA_NSS=D0 + -D SX126X_RXEN=D7 + -D SX126X_TXEN=RADIOLIB_NC + -D SX126X_DIO2_AS_RF_SWITCH=1 + -D SX126X_DIO3_TCXO_VOLTAGE=1.8 + -D SX126X_CURRENT_LIMIT=140 + -D SX126X_RX_BOOSTED_GAIN=1 + -D PIN_WIRE_SCL=5 + -D PIN_WIRE_SDA=4 + -UENV_INCLUDE_GPS +debug_tool = jlink +upload_protocol = nrfutil +lib_deps = ${nrf52_base.lib_deps} + ${sensor_base.lib_deps} +build_src_filter = ${nrf52_base.build_src_filter} + + + +[ikoka_nano_nrf_e22_22dbm] +extends = ikoka_nano_nrf +build_flags = + ${ikoka_nano_nrf.build_flags} + -D MANUFACTURER_STRING='"Ikoka Nano-E22-22dBm (Xiao_nrf52)"' + -D LORA_TX_POWER=22 +build_src_filter = ${ikoka_nano_nrf.build_src_filter} + + + + + +<../variants/ikoka_nano_nrf> + +[ikoka_nano_nrf_e22_30dbm] +extends = ikoka_nano_nrf +build_flags = + ${ikoka_nano_nrf.build_flags} + -D MANUFACTURER_STRING='"Ikoka Nano-E22-30dBm (Xiao_nrf52)"' + -D LORA_TX_POWER=20 +build_src_filter = ${ikoka_nano_nrf.build_src_filter} + + + + + +<../variants/ikoka_nano_nrf> + +[ikoka_nano_nrf_e22_33dbm] +extends = ikoka_nano_nrf +build_flags = + ${ikoka_nano_nrf.build_flags} + -D MANUFACTURER_STRING='"Ikoka Nano-E22-33dBm (Xiao_nrf52)"' + -D LORA_TX_POWER=9 +build_src_filter = ${ikoka_nano_nrf.build_src_filter} + + + + + +<../variants/ikoka_nano_nrf> + +[ikoka_nano_nrf_companion_radio_ble] +extends = ikoka_nano_nrf +board_build.ldscript = boards/nrf52840_s140_v7_extrafs.ld +board_upload.maximum_size = 708608 +build_flags = + ${ikoka_nano_nrf.build_flags} + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D BLE_PIN_CODE=123456 + -D OFFLINE_QUEUE_SIZE=256 + -I examples/companion_radio/ui-new + -D QSPIFLASH=1 +build_src_filter = ${ikoka_nano_nrf.build_src_filter} + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${ikoka_nano_nrf.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[ikoka_nano_nrf_companion_radio_usb] +extends = ikoka_nano_nrf +board_build.ldscript = boards/nrf52840_s140_v7_extrafs.ld +board_upload.maximum_size = 708608 +build_flags = + ${ikoka_nano_nrf.build_flags} + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -I examples/companion_radio/ui-new + -D QSPIFLASH=1 + -D ENABLE_USB_INTERFACE +build_src_filter = ${ikoka_nano_nrf.build_src_filter} + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${ikoka_nano_nrf.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[ikoka_nano_nrf_repeater] +extends = ikoka_nano_nrf +build_flags = + ${ikoka_nano_nrf.build_flags} + -D ADVERT_NAME='"Ikoka Nano Repeater"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 +build_src_filter = ${ikoka_nano_nrf.build_src_filter} + +<../examples/simple_repeater/*.cpp> + +[ikoka_nano_nrf_room_server] +extends = ikoka_nano_nrf +build_flags = + ${ikoka_nano_nrf.build_flags} + -D ADVERT_NAME='"Ikoka Nano Room"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' +build_src_filter = ${ikoka_nano_nrf.build_src_filter} + +<../examples/simple_room_server/*.cpp> + +[env:ikoka_nano_nrf_22dbm_companion_radio_usb] +extends = + ikoka_nano_nrf_e22_22dbm + ikoka_nano_nrf_companion_radio_usb +build_flags = + ${ikoka_nano_nrf_companion_radio_usb.build_flags} + ${ikoka_nano_nrf_e22_22dbm.build_flags} +build_src_filter = + ${ikoka_nano_nrf_companion_radio_usb.build_src_filter} + ${ikoka_nano_nrf_e22_22dbm.build_src_filter} + +[env:ikoka_nano_nrf_22dbm_companion_radio_ble] +extends = + ikoka_nano_nrf_e22_22dbm + ikoka_nano_nrf_companion_radio_ble +build_flags = + ${ikoka_nano_nrf_companion_radio_ble.build_flags} + ${ikoka_nano_nrf_e22_22dbm.build_flags} +build_src_filter = + ${ikoka_nano_nrf_companion_radio_ble.build_src_filter} + ${ikoka_nano_nrf_e22_22dbm.build_src_filter} + +[env:ikoka_nano_nrf_22dbm_repeater] +extends = + ikoka_nano_nrf_e22_22dbm + ikoka_nano_nrf_repeater +build_flags = + ${ikoka_nano_nrf_repeater.build_flags} + ${ikoka_nano_nrf_e22_22dbm.build_flags} +build_src_filter = + ${ikoka_nano_nrf_repeater.build_src_filter} + ${ikoka_nano_nrf_e22_22dbm.build_src_filter} + +[env:ikoka_nano_nrf_22dbm_room_server] +extends = + ikoka_nano_nrf_e22_22dbm + ikoka_nano_nrf_room_server +build_flags = + ${ikoka_nano_nrf_room_server.build_flags} + ${ikoka_nano_nrf_e22_22dbm.build_flags} +build_src_filter = + ${ikoka_nano_nrf_room_server.build_src_filter} + ${ikoka_nano_nrf_e22_22dbm.build_src_filter} + +[env:ikoka_nano_nrf_30dbm_companion_radio_usb] +extends = + ikoka_nano_nrf_e22_30dbm + ikoka_nano_nrf_companion_radio_usb +build_flags = + ${ikoka_nano_nrf_companion_radio_usb.build_flags} + ${ikoka_nano_nrf_e22_30dbm.build_flags} +build_src_filter = + ${ikoka_nano_nrf_companion_radio_usb.build_src_filter} + ${ikoka_nano_nrf_e22_30dbm.build_src_filter} + +[env:ikoka_nano_nrf_30dbm_companion_radio_ble] +extends = + ikoka_nano_nrf_e22_30dbm + ikoka_nano_nrf_companion_radio_ble +build_flags = + ${ikoka_nano_nrf_companion_radio_ble.build_flags} + ${ikoka_nano_nrf_e22_30dbm.build_flags} +build_src_filter = + ${ikoka_nano_nrf_companion_radio_ble.build_src_filter} + ${ikoka_nano_nrf_e22_30dbm.build_src_filter} + +[env:ikoka_nano_nrf_30dbm_repeater] +extends = + ikoka_nano_nrf_e22_30dbm + ikoka_nano_nrf_repeater +build_flags = + ${ikoka_nano_nrf_repeater.build_flags} + ${ikoka_nano_nrf_e22_30dbm.build_flags} +build_src_filter = + ${ikoka_nano_nrf_repeater.build_src_filter} + ${ikoka_nano_nrf_e22_30dbm.build_src_filter} + +[env:ikoka_nano_nrf_30dbm_room_server] +extends = + ikoka_nano_nrf_e22_30dbm + ikoka_nano_nrf_room_server +build_flags = + ${ikoka_nano_nrf_room_server.build_flags} + ${ikoka_nano_nrf_e22_30dbm.build_flags} +build_src_filter = + ${ikoka_nano_nrf_room_server.build_src_filter} + ${ikoka_nano_nrf_e22_30dbm.build_src_filter} + +[env:ikoka_nano_nrf_33dbm_companion_radio_usb] +extends = + ikoka_nano_nrf_e22_33dbm + ikoka_nano_nrf_companion_radio_usb +build_flags = + ${ikoka_nano_nrf_companion_radio_usb.build_flags} + ${ikoka_nano_nrf_e22_33dbm.build_flags} +build_src_filter = + ${ikoka_nano_nrf_companion_radio_usb.build_src_filter} + ${ikoka_nano_nrf_e22_33dbm.build_src_filter} + +[env:ikoka_nano_nrf_33dbm_companion_radio_ble] +extends = + ikoka_nano_nrf_e22_33dbm + ikoka_nano_nrf_companion_radio_ble +build_flags = + ${ikoka_nano_nrf_companion_radio_ble.build_flags} + ${ikoka_nano_nrf_e22_33dbm.build_flags} +build_src_filter = + ${ikoka_nano_nrf_companion_radio_ble.build_src_filter} + ${ikoka_nano_nrf_e22_33dbm.build_src_filter} + +[env:ikoka_nano_nrf_33dbm_repeater] +extends = + ikoka_nano_nrf_e22_33dbm + ikoka_nano_nrf_repeater +build_flags = + ${ikoka_nano_nrf_repeater.build_flags} + ${ikoka_nano_nrf_e22_33dbm.build_flags} +build_src_filter = + ${ikoka_nano_nrf_repeater.build_src_filter} + ${ikoka_nano_nrf_e22_33dbm.build_src_filter} + +[env:ikoka_nano_nrf_33dbm_room_server] +extends = + ikoka_nano_nrf_e22_33dbm + ikoka_nano_nrf_room_server +build_flags = + ${ikoka_nano_nrf_room_server.build_flags} + ${ikoka_nano_nrf_e22_33dbm.build_flags} +build_src_filter = + ${ikoka_nano_nrf_room_server.build_src_filter} + ${ikoka_nano_nrf_e22_33dbm.build_src_filter} + +[env:ikoka_nano_nrf_22dbm_kiss_modem] +extends = ikoka_nano_nrf_e22_22dbm +build_src_filter = ${ikoka_nano_nrf_e22_22dbm.build_src_filter} + +<../examples/kiss_modem/> + +[env:ikoka_nano_nrf_30dbm_kiss_modem] +extends = ikoka_nano_nrf_e22_30dbm +build_src_filter = ${ikoka_nano_nrf_e22_30dbm.build_src_filter} + +<../examples/kiss_modem/> + +[env:ikoka_nano_nrf_33dbm_kiss_modem] +extends = ikoka_nano_nrf_e22_33dbm +build_src_filter = ${ikoka_nano_nrf_e22_33dbm.build_src_filter} + +<../examples/kiss_modem/> + +[Heltec_E213_base] +extends = esp32_base +board = heltec_e213 +build_flags = + ${esp32_base.build_flags} + -I variants/heltec_e213 + -D Vision_Master_E213 + -D ARDUINO_USB_CDC_ON_BOOT=1 + -D USE_SX1262 + -D RADIO_CLASS=CustomSX1262 + -D WRAPPER_CLASS=CustomSX1262Wrapper + -D P_LORA_DIO_1=14 + -D P_LORA_NSS=8 + -D P_LORA_RESET=12 + -D P_LORA_BUSY=13 + -D P_LORA_SCLK=9 + -D P_LORA_MISO=11 + -D P_LORA_MOSI=10 + -D P_LORA_TX_LED=45 + -D LORA_TX_POWER=22 + -D PIN_USER_BTN=0 + -D PIN_VEXT_EN=18 + -D PIN_VEXT_EN_ACTIVE=HIGH + -D PIN_VBAT_READ=7 + -D PIN_ADC_CTRL=46 + -D SX126X_DIO2_AS_RF_SWITCH=true + -D SX126X_DIO3_TCXO_VOLTAGE=1.8 + -D SX126X_CURRENT_LIMIT=140 + -D SX126X_RX_BOOSTED_GAIN=1 + -D PIN_BOARD_SDA=39 + -D PIN_BOARD_SCL=38 + -D DISP_CS=5 + -D DISP_BUSY=1 + -D DISP_DC=2 + -D DISP_RST=3 + -D DISP_SCLK=4 + -D DISP_MOSI=6 +build_src_filter = ${esp32_base.build_src_filter} + +<../variants/heltec_e213> +lib_deps = + ${esp32_base.lib_deps} + https://github.com/Quency-D/heltec-eink-modules/archive/563dd41fd850a1bc3039b8723da4f3a20fe1c800.zip + +[env:Heltec_E213_companion_radio_ble] +extends = Heltec_E213_base +build_flags = + ${Heltec_E213_base.build_flags} + -I examples/companion_radio/ui-new + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D DISPLAY_CLASS=E213Display + -D AUTO_OFF_MILLIS=0 + -D BLE_PIN_CODE=123456 + -D BLE_DEBUG_LOGGING=1 + -D OFFLINE_QUEUE_SIZE=256 +build_src_filter = ${Heltec_E213_base.build_src_filter} + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${Heltec_E213_base.lib_deps} + densaugeo/base64 @ ~1.4.0 + bakercp/CRC32 @ ^2.0.0 + +[env:Heltec_E213_companion_radio_usb] +extends = Heltec_E213_base +build_flags = + ${Heltec_E213_base.build_flags} + -I examples/companion_radio/ui-new + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D DISPLAY_CLASS=E213Display + -D AUTO_OFF_MILLIS=0 + -D OFFLINE_QUEUE_SIZE=256 + -D ENABLE_USB_INTERFACE +build_src_filter = ${Heltec_E213_base.build_src_filter} + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${Heltec_E213_base.lib_deps} + densaugeo/base64 @ ~1.4.0 + bakercp/CRC32 @ ^2.0.0 + +[env:Heltec_E213_repeater] +extends = Heltec_E213_base +build_flags = + ${Heltec_E213_base.build_flags} + -D DISPLAY_CLASS=E213Display + -D ADVERT_NAME='"Heltec E213 Repeater"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 +build_src_filter = ${Heltec_E213_base.build_src_filter} + + + +<../examples/simple_repeater> +lib_deps = + ${Heltec_E213_base.lib_deps} + ${esp32_ota.lib_deps} + bakercp/CRC32 @ ^2.0.0 + +[env:Heltec_E213_repeater_bridge_espnow] +extends = Heltec_E213_base +build_flags = + ${Heltec_E213_base.build_flags} + -D DISPLAY_CLASS=E213Display + -D ADVERT_NAME='"ESPNow Bridge"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 + -D WITH_ESPNOW_BRIDGE=1 +build_src_filter = ${Heltec_E213_base.build_src_filter} + + + + + +<../examples/simple_repeater> +lib_deps = + ${Heltec_E213_base.lib_deps} + ${esp32_ota.lib_deps} + bakercp/CRC32 @ ^2.0.0 + +[env:Heltec_E213_room_server] +extends = Heltec_E213_base +build_flags = + ${Heltec_E213_base.build_flags} + -D DISPLAY_CLASS=E213Display + -D ADVERT_NAME='"Heltec E213 Room"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D ROOM_PASSWORD='"hello"' +build_src_filter = ${Heltec_E213_base.build_src_filter} + + + +<../examples/simple_room_server> +lib_deps = + ${Heltec_E213_base.lib_deps} + ${esp32_ota.lib_deps} + bakercp/CRC32 @ ^2.0.0 + +[env:Heltec_E213_kiss_modem] +extends = Heltec_E213_base +build_src_filter = ${Heltec_E213_base.build_src_filter} + +<../examples/kiss_modem/> + +[Heltec_tracker_v1_1_base] +extends = esp32_base +board = esp32-s3-devkitc-1 +build_flags = + ${esp32_base.build_flags} + ${sensor_base.build_flags} + -I variants/heltec_tracker_v1_1 + -D HELTEC_LORA_V3 + -D ARDUINO_USB_CDC_ON_BOOT=1 + -D ESP32_CPU_FREQ=80 + -D P_LORA_DIO_1=14 + -D P_LORA_NSS=8 + -D P_LORA_RESET=RADIOLIB_NC + -D P_LORA_BUSY=13 + -D P_LORA_SCLK=9 + -D P_LORA_MISO=11 + -D P_LORA_MOSI=10 + -D RADIO_CLASS=CustomSX1262 + -D WRAPPER_CLASS=CustomSX1262Wrapper + -D LORA_TX_POWER=22 + -D P_LORA_TX_LED=18 + -D PIN_BOARD_SDA=45 + -D PIN_BOARD_SCL=46 + -D PIN_USER_BTN=0 + -D PIN_ADC_CTRL=2 + -D PIN_TFT_SDA=42 + -D PIN_TFT_SCL=41 + -D PIN_TFT_DC=40 + -D PIN_TFT_RST=39 + -D PIN_TFT_CS=38 + -D USE_PIN_TFT=1 + -D PIN_VEXT_EN=3 + -D PIN_TFT_LEDA_CTL=21 + -D PIN_GPS_RX=33 + -D PIN_GPS_TX=34 + -D PIN_GPS_PPS=36 + -D PIN_GPS_RST=35 + -D PIN_GPS_EN=3 + -D ENV_PIN_SDA=PIN_BOARD_SDA + -D ENV_PIN_SCL=PIN_BOARD_SCL + -D ENV_INCLUDE_GPS=1 + -D ENV_INCLUDE_INA3221=1 + -D ENV_INCLUDE_BME680=1 + -D BME680_BSEC2_SUPPORTED=1 + -D ENV_INCLUDE_BMP085=0 + -D TELEM_BME680_ADDRESS=0x77 + -D GPS_BAUD_RATE=115200 + -D SX126X_DIO2_AS_RF_SWITCH=true + -D SX126X_DIO3_TCXO_VOLTAGE=1.8 + -D SX126X_CURRENT_LIMIT=140 + -D SX126X_RX_BOOSTED_GAIN=1 +build_src_filter = ${esp32_base.build_src_filter} + +<../variants/heltec_tracker_v1_1> + + +lib_deps = + ${esp32_base.lib_deps} + ${sensor_base.lib_deps} + stevemarple/MicroNMEA @ ^2.0.6 + bodmer/TFT_eSPI @ ^2.5.43 + +[env:Heltec_Wireless_Tracker_v1_1_companion_radio_ble] +extends = Heltec_tracker_v1_1_base +build_flags = + ${Heltec_tracker_v1_1_base.build_flags} + -I src/helpers/ui + -I examples/companion_radio/ui-new + -D ARDUINO_USB_CDC_ON_BOOT=1 + -D DISPLAY_ROTATION=1 + -D DISPLAY_CLASS=ST7735Display + -D MAX_CONTACTS=300 + -D MAX_GROUP_CHANNELS=8 + -D BLE_PIN_CODE=123456 + -D OFFLINE_QUEUE_SIZE=256 + -D BLE_DEBUG_LOGGING=1 + -D MESH_PACKET_LOGGING=1 + -D MESH_DEBUG=1 +build_src_filter = ${Heltec_tracker_v1_1_base.build_src_filter} + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> + + +lib_deps = + ${Heltec_tracker_v1_1_base.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:Heltec_Wireless_Tracker_v1_1_repeater] +extends = Heltec_tracker_v1_1_base +build_flags = + ${Heltec_tracker_v1_1_base.build_flags} + -D DISPLAY_ROTATION=1 + -D DISPLAY_CLASS=ST7735Display + -D ADVERT_NAME='"Heltec Repeater"' + -D PERSISTANT_GPS=1 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 + -D MESH_PACKET_LOGGING=1 + -D MESH_DEBUG=1 +build_src_filter = ${Heltec_tracker_v1_1_base.build_src_filter} + + + +<../examples/simple_repeater> +lib_deps = + ${Heltec_tracker_v1_1_base.lib_deps} + ${esp32_ota.lib_deps} + bodmer/TFT_eSPI@^2.5.43 + +[env:Heltec_Wireless_Tracker_v1_1_repeater_bridge_espnow] +extends = Heltec_tracker_v1_1_base +build_flags = + ${Heltec_tracker_v1_1_base.build_flags} + -D DISPLAY_ROTATION=1 + -D DISPLAY_CLASS=ST7735Display + -D ADVERT_NAME='"ESPNow Bridge"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 + -D WITH_ESPNOW_BRIDGE=1 + -D WITH_ESPNOW_BRIDGE_SECRET='"shared-secret"' +build_src_filter = ${Heltec_tracker_v1_1_base.build_src_filter} + + + + + +<../examples/simple_repeater> +lib_deps = + ${Heltec_tracker_v1_1_base.lib_deps} + ${esp32_ota.lib_deps} + +[env:Heltec_Wireless_Tracker_room_server] +extends = Heltec_tracker_base +build_flags = + ${Heltec_tracker_base.build_flags} + -D DISPLAY_ROTATION=1 + -D DISPLAY_CLASS=ST7735Display + -D ADVERT_NAME='"Heltec Room"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D ROOM_PASSWORD='"hello"' +build_src_filter = ${Heltec_tracker_base.build_src_filter} + + + +<../examples/simple_room_server> +lib_deps = + ${Heltec_tracker_base.lib_deps} + ${esp32_ota.lib_deps} + +[Heltec_tracker_base] +extends = esp32_base +board = esp32-s3-devkitc-1 +build_flags = + ${esp32_base.build_flags} + -I variants/heltec_tracker + -D HELTEC_LORA_V3 + -D ARDUINO_USB_CDC_ON_BOOT=1 + -D ESP32_CPU_FREQ=80 + -D P_LORA_DIO_1=14 + -D P_LORA_NSS=8 + -D P_LORA_RESET=RADIOLIB_NC + -D P_LORA_BUSY=13 + -D P_LORA_SCLK=9 + -D P_LORA_MISO=11 + -D P_LORA_MOSI=10 + -D USE_SX1262 + -D RADIO_CLASS=CustomSX1262 + -D WRAPPER_CLASS=CustomSX1262Wrapper + -D LORA_TX_POWER=22 + -D P_LORA_TX_LED=18 + -D PIN_BOARD_SDA=45 + -D PIN_BOARD_SCL=46 + -D PIN_USER_BTN=0 + -D PIN_ADC_CTRL=2 + -D PIN_TFT_SDA=42 + -D PIN_TFT_SCL=41 + -D PIN_TFT_DC=40 + -D PIN_TFT_RST=39 + -D PIN_TFT_CS=38 + -D USE_PIN_TFT=1 + -D PIN_VEXT_EN=3 + -D PIN_TFT_LEDA_CTL=21 + -D PIN_GPS_RX=33 + -D PIN_GPS_TX=34 + -D PIN_GPS_EN=35 + -D PIN_GPS_RESET=36 + -D PIN_GPS_RESET_ACTIVE=LOW + -D GPS_BAUD_RATE=115200 + -D ENV_INCLUDE_GPS=1 + -D SX126X_DIO2_AS_RF_SWITCH=true + -D SX126X_DIO3_TCXO_VOLTAGE=1.8 + -D SX126X_CURRENT_LIMIT=140 + -D SX126X_RX_BOOSTED_GAIN=1 +build_src_filter = ${esp32_base.build_src_filter} + +<../variants/heltec_tracker> +lib_deps = + ${esp32_base.lib_deps} + stevemarple/MicroNMEA @ ^2.0.6 + bodmer/TFT_eSPI @ ^2.4.31 + +[env:Heltec_Wireless_Tracker_companion_radio_usb] +extends = Heltec_tracker_base +build_flags = + ${Heltec_tracker_base.build_flags} + -I src/helpers/ui + -I examples/companion_radio/ui-new + -D DISPLAY_ROTATION=1 + -D DISPLAY_CLASS=ST7735Display + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D ENABLE_USB_INTERFACE +build_src_filter = ${Heltec_tracker_base.build_src_filter} + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> + + +lib_deps = + ${Heltec_tracker_base.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:Heltec_Wireless_Tracker_companion_radio_ble] +extends = Heltec_tracker_base +build_flags = + ${Heltec_tracker_base.build_flags} + -I src/helpers/ui + -I examples/companion_radio/ui-new + -D DISPLAY_ROTATION=1 + -D DISPLAY_CLASS=ST7735Display + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D BLE_PIN_CODE=123456 + -D OFFLINE_QUEUE_SIZE=256 +build_src_filter = ${Heltec_tracker_base.build_src_filter} + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> + + +lib_deps = + ${Heltec_tracker_base.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:Heltec_Wireless_Tracker_repeater] +extends = Heltec_tracker_base +build_flags = + ${Heltec_tracker_base.build_flags} + -D DISPLAY_ROTATION=1 + -D DISPLAY_CLASS=ST7735Display + -D ADVERT_NAME='"Heltec Repeater"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 +build_src_filter = ${Heltec_tracker_base.build_src_filter} + + + +<../examples/simple_repeater> +lib_deps = + ${Heltec_tracker_base.lib_deps} + ${esp32_ota.lib_deps} + +[env:Heltec_Wireless_Tracker_repeater_bridge_espnow] +extends = Heltec_tracker_base +build_flags = + ${Heltec_tracker_base.build_flags} + -D DISPLAY_ROTATION=1 + -D DISPLAY_CLASS=ST7735Display + -D ADVERT_NAME='"ESPNow Bridge"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 + -D WITH_ESPNOW_BRIDGE=1 +build_src_filter = ${Heltec_tracker_base.build_src_filter} + + + + + +<../examples/simple_repeater> +lib_deps = + ${Heltec_tracker_base.lib_deps} + ${esp32_ota.lib_deps} + +[env:Heltec_Wireless_Tracker_kiss_modem] +extends = Heltec_tracker_base +build_src_filter = ${Heltec_tracker_base.build_src_filter} + +<../examples/kiss_modem/> + +[Promicro] +extends = nrf52_base +board = promicro_nrf52840 +build_flags = ${nrf52_base.build_flags} + -I variants/promicro + -D PROMICRO + -D USE_SX1262 + -D RADIO_CLASS=CustomSX1262 + -D WRAPPER_CLASS=CustomSX1262Wrapper + -D LORA_TX_POWER=22 + -D SX126X_CURRENT_LIMIT=140 + -D SX126X_RX_BOOSTED_GAIN=1 + -D PIN_BOARD_SCL=7 + -D PIN_BOARD_SDA=8 + -D PIN_OLED_RESET=-1 + -D PIN_USER_BTN=6 + -D PIN_GPS_RX=3 + -D PIN_GPS_TX=4 + -D PIN_GPS_EN=5 + -D ENV_INCLUDE_GPS=1 + -D ENV_INCLUDE_AHTX0=1 + -D ENV_INCLUDE_BME280=1 + -D ENV_INCLUDE_BMP280=1 + -D ENV_INCLUDE_INA3221=1 + -D ENV_INCLUDE_INA219=1 + -D ENV_INCLUDE_INA226=1 +build_src_filter = ${nrf52_base.build_src_filter} + + + +<../variants/promicro> +lib_deps = ${nrf52_base.lib_deps} + adafruit/Adafruit SSD1306 @ ^2.5.13 + adafruit/Adafruit INA3221 Library @ ^1.0.1 + adafruit/Adafruit INA219 @ ^1.2.3 + adafruit/Adafruit AHTX0 @ ^2.0.5 + adafruit/Adafruit BME280 Library @ ^2.3.0 + adafruit/Adafruit BMP280 Library@^2.6.8 + stevemarple/MicroNMEA @ ^2.0.6 + robtillaart/INA226@^0.6.6 + +[env:ProMicro_repeater] +extends = Promicro +build_src_filter = ${Promicro.build_src_filter} + +<../examples/simple_repeater> + + + + +build_flags = + ${Promicro.build_flags} + -D ADVERT_NAME='"ProMicro Repeater"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 + -D DISPLAY_CLASS=SSD1306Display +lib_deps = ${Promicro.lib_deps} + adafruit/RTClib @ ^2.1.3 + +[env:ProMicro_repeater_bridge_rs232_serial1] +extends = Promicro +build_src_filter = ${Promicro.build_src_filter} + +<../examples/simple_repeater> + + + + + + +build_flags = + ${Promicro.build_flags} + -D ADVERT_NAME='"RS232 Bridge"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 + -D DISPLAY_CLASS=SSD1306Display + -D WITH_RS232_BRIDGE=Serial1 + -D WITH_RS232_BRIDGE_RX=PIN_SERIAL1_RX + -D WITH_RS232_BRIDGE_TX=PIN_SERIAL1_TX + -UENV_INCLUDE_GPS +lib_deps = ${Promicro.lib_deps} + adafruit/RTClib @ ^2.1.3 + +[env:ProMicro_room_server] +extends = Promicro +build_src_filter = ${Promicro.build_src_filter} + +<../examples/simple_room_server> + + + + +build_flags = ${Promicro.build_flags} + -D ADVERT_NAME='"ProMicro Room"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D ROOM_PASSWORD='"hello"' + -D DISPLAY_CLASS=SSD1306Display +lib_deps = ${Promicro.lib_deps} + adafruit/RTClib @ ^2.1.3 + +[env:ProMicro_terminal_chat] +extends = Promicro +build_flags = ${Promicro.build_flags} + -D MAX_CONTACTS=100 + -D MAX_GROUP_CHANNELS=1 +build_src_filter = ${Promicro.build_src_filter} + +<../examples/simple_secure_chat/main.cpp> +lib_deps = ${Promicro.lib_deps} + densaugeo/base64 @ ~1.4.0 + adafruit/RTClib @ ^2.1.3 + +[env:ProMicro_companion_radio_usb] +extends = Promicro +board_build.ldscript = boards/nrf52840_s140_v6_extrafs.ld +board_upload.maximum_size = 712704 +build_flags = ${Promicro.build_flags} + -I examples/companion_radio/ui-new + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D DISPLAY_CLASS=SSD1306Display + -D ENABLE_USB_INTERFACE +build_src_filter = ${Promicro.build_src_filter} + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = ${Promicro.lib_deps} + adafruit/RTClib @ ^2.1.3 + densaugeo/base64 @ ~1.4.0 + +[env:ProMicro_companion_radio_ble] +extends = Promicro +board_build.ldscript = boards/nrf52840_s140_v6_extrafs.ld +board_upload.maximum_size = 712704 +build_flags = ${Promicro.build_flags} + -I examples/companion_radio/ui-new + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D BLE_PIN_CODE=123456 + -D BLE_DEBUG_LOGGING=1 + -D OFFLINE_QUEUE_SIZE=256 + -D DISPLAY_CLASS=SSD1306Display +build_src_filter = ${Promicro.build_src_filter} + + + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = ${Promicro.lib_deps} + adafruit/RTClib @ ^2.1.3 + densaugeo/base64 @ ~1.4.0 + +[env:ProMicro_sensor] +extends = Promicro +build_flags = + ${Promicro.build_flags} + -D ADVERT_NAME='"ProMicro Sensor"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D DISPLAY_CLASS=SSD1306Display +build_src_filter = ${Promicro.build_src_filter} + + + + + +<../examples/simple_sensor> +lib_deps = + ${Promicro.lib_deps} + +[env:ProMicro_kiss_modem] +extends = Promicro +build_src_filter = ${Promicro.build_src_filter} + +<../examples/kiss_modem/> + +[rak3x72] +extends = stm32_base +board = rak3172 +board_upload.maximum_size = 229376 +build_flags = ${stm32_base.build_flags} + -D RAK_3X72 + -D RADIO_CLASS=CustomSTM32WLx + -D WRAPPER_CLASS=CustomSTM32WLxWrapper + -D SPI_INTERFACES_COUNT=0 + -D RX_BOOSTED_GAIN=true + -I variants/rak3x72 +build_src_filter = ${stm32_base.build_src_filter} + +<../variants/rak3x72> + +[env:RAK_3x72_repeater] +extends = rak3x72 +build_flags = ${rak3x72.build_flags} + -D ADVERT_NAME='"RAK3x72 Repeater"' + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 +build_src_filter = ${rak3x72.build_src_filter} + +<../examples/simple_repeater/*.cpp> + +[env:RAK_3x72_sensor] +extends = rak3x72 +build_flags = ${rak3x72.build_flags} + -D ADVERT_NAME='"RAK3x72 Sensor"' + -D ADMIN_PASSWORD='"password"' +build_src_filter = ${rak3x72.build_src_filter} + +<../examples/simple_sensor> + +[env:RAK_3x72_companion_radio_usb] +extends = rak3x72 +build_flags = ${rak3x72.build_flags} + -D MAX_CONTACTS=100 + -D MAX_GROUP_CHANNELS=8 + -D ENABLE_USB_INTERFACE +build_src_filter = ${rak3x72.build_src_filter} + +<../examples/companion_radio/*.cpp> +lib_deps = ${rak3x72.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:RAK_3x72_kiss_modem] +extends = rak3x72 +build_src_filter = ${rak3x72.build_src_filter} + +<../examples/kiss_modem/> + +[SenseCapIndicator-ESPNow] +extends = esp32_base +board = esp32-s3-devkitc-1 +board_build.arduino.memory_type = qio_opi +board_build.flash_mode = qio +board_build.psram_type = opi +board_upload.flash_size = 8MB +board_upload.maximum_size = 8388608 +board_build.partitions = default.csv +build_flags = + ${esp32_base.build_flags} + -D PIN_BOARD_SDA=39 + -D PIN_BOARD_SCL=40 + -D DISPLAY_CLASS=SCIndicatorDisplay + -D DISPLAY_LINES=21 + -D LINE_LENGTH=53 + -D DISABLE_WIFI_OTA=1 + -D IO_EXPANDER=0x40 + -D IO_EXPANDER_IRQ=42 + -D UI_ZOOM=3.5 + -D UI_RECENT_LIST_SIZE=9 + -D UI_SENSORS_PAGE=1 + -D PIN_USER_BTN=38 + -D HAS_TOUCH + -I variants/sensecap_indicator-espnow +build_src_filter = ${esp32_base.build_src_filter} + +<../variants/sensecap_indicator-espnow/*.cpp> + + + + + + +lib_deps = ${esp32_base.lib_deps} + adafruit/Adafruit BusIO @ ^1.17.2 + lovyan03/LovyanGFX @ ^1.2.7 + +[env:SenseCapIndicator-ESPNow_comp_radio_usb] +extends = SenseCapIndicator-ESPNow +build_flags = + ${SenseCapIndicator-ESPNow.build_flags} + -I examples/companion_radio/ui-new + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 +build_src_filter = ${SenseCapIndicator-ESPNow.build_src_filter} + +<../examples/companion_radio/ui-new/*.cpp> + +<../examples/companion_radio/*.cpp> +lib_deps = + ${SenseCapIndicator-ESPNow.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[M5Stack_Unit_C6L] +extends = esp32c6_base +board = esp32-c6-devkitm-1 +board_build.partitions = min_spiffs.csv +board_build.flash_mode = dio +build_flags = + ${esp32c6_base.build_flags} + ${sensor_base.build_flags} + -I variants/m5stack_unit_c6l + -D P_LORA_TX_LED=15 + -D P_LORA_SCLK=20 + -D P_LORA_MISO=22 + -D P_LORA_MOSI=21 + -D P_LORA_NSS=23 + -D P_LORA_DIO_1=7 + -D P_LORA_BUSY=19 + -D P_LORA_RESET=-1 + -D PIN_BUZZER=11 + -D PIN_BOARD_SDA=16 + -D PIN_BOARD_SCL=17 + -D SX126X_RXEN=5 + -D SX126X_DIO2_AS_RF_SWITCH=true + -D SX126X_DIO3_TCXO_VOLTAGE=1.8 + -D SX126X_CURRENT_LIMIT=140 + -D SX126X_RX_BOOSTED_GAIN=1 + -D USE_SX1262 + -D RADIO_CLASS=CustomSX1262 + -D WRAPPER_CLASS=CustomSX1262Wrapper + -D LORA_TX_POWER=22 + -D DISABLE_WIFI_OTA=1 + -D GPS_RX=4 + -D GPS_TX=5 +build_src_filter = ${esp32c6_base.build_src_filter} + +<../variants/m5stack_unit_c6l> + + +lib_deps = + ${esp32c6_base.lib_deps} + ${sensor_base.lib_deps} + +[env:M5Stack_Unit_C6L_repeater] +extends = M5Stack_Unit_C6L +build_src_filter = ${M5Stack_Unit_C6L.build_src_filter} + +<../examples/simple_repeater/*.cpp> +build_flags = + ${M5Stack_Unit_C6L.build_flags} + -D ADVERT_NAME='"Unit C6L Repeater"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 +lib_deps = + ${M5Stack_Unit_C6L.lib_deps} + +[env:M5Stack_Unit_C6L_room_server] +extends = M5Stack_Unit_C6L +build_src_filter = ${M5Stack_Unit_C6L.build_src_filter} + +<../examples/simple_room_server> +build_flags = + ${M5Stack_Unit_C6L.build_flags} + -D ADVERT_NAME='"Unit C6L Room"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D ROOM_PASSWORD='"hello"' +lib_deps = + ${M5Stack_Unit_C6L.lib_deps} + +[env:M5Stack_Unit_C6L_companion_radio_ble] +extends = M5Stack_Unit_C6L +build_flags = ${M5Stack_Unit_C6L.build_flags} + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D BLE_PIN_CODE=123456 + -D BLE_DEBUG_LOGGING=1 + -D OFFLINE_QUEUE_SIZE=256 +build_src_filter = ${M5Stack_Unit_C6L.build_src_filter} + + + - + +<../examples/companion_radio/*.cpp> +lib_deps = + ${M5Stack_Unit_C6L.lib_deps} + densaugeo/base64 @ ~1.4.0 + end2endzone/NonBlockingRTTTL@^1.3.0 + +[env:M5Stack_Unit_C6L_companion_radio_usb] +extends = M5Stack_Unit_C6L +build_flags = ${M5Stack_Unit_C6L.build_flags} + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D OFFLINE_QUEUE_SIZE=256 + -D ARDUINO_USB_CDC_ON_BOOT=1 + -D ARDUINO_USB_MODE=1 + -D ENABLE_USB_INTERFACE +build_src_filter = ${M5Stack_Unit_C6L.build_src_filter} + + + - + +<../examples/companion_radio/*.cpp> +lib_deps = + ${M5Stack_Unit_C6L.lib_deps} + densaugeo/base64 @ ~1.4.0 + end2endzone/NonBlockingRTTTL@^1.3.0 + +[env:M5Stack_Unit_C6L_kiss_modem] +extends = M5Stack_Unit_C6L +build_src_filter = ${M5Stack_Unit_C6L.build_src_filter} + +<../examples/kiss_modem/> + +[WioTrackerL1Eink] +extends = nrf52_base +board = seeed-wio-tracker-l1 +board_build.ldscript = boards/nrf52840_s140_v7.ld +build_flags = ${nrf52_base.build_flags} + ${sensor_base.build_flags} + -I lib/nrf52/s140_nrf52_7.3.0_API/include + -I lib/nrf52/s140_nrf52_7.3.0_API/include/nrf52 + -I variants/wio-tracker-l1 + -D WIO_TRACKER_L1 + -D WIO_TRACKER_L1_EINK + -D USE_SX1262 + -D RADIO_CLASS=CustomSX1262 + -D WRAPPER_CLASS=CustomSX1262Wrapper + -D LORA_TX_POWER=22 + -D SX126X_CURRENT_LIMIT=140 + -D SX126X_RX_BOOSTED_GAIN=1 + -D PIN_OLED_RESET=-1 + -D EINK_DISPLAY_MODEL=GxEPD2_213_B74 + -D EINK_SCALE_X=1.953125f + -D EINK_SCALE_Y=1.28f + -D EINK_X_OFFSET=0 + -D EINK_Y_OFFSET=10 + -D DISPLAY_ROTATION=1 + -D DISABLE_DIAGNOSTIC_OUTPUT + -D AUTO_OFF_MILLIS=0 + -D GPS_BAUD_RATE=9600 + -D ENV_PIN_SDA=PIN_WIRE1_SDA + -D ENV_PIN_SCL=PIN_WIRE1_SCL +build_src_filter = ${nrf52_base.build_src_filter} + + + +<../variants/wio-tracker-l1> + + + + +lib_deps = ${nrf52_base.lib_deps} + ${sensor_base.lib_deps} + adafruit/Adafruit GFX Library @ ^1.12.1 + zinggjm/GxEPD2 @ 1.6.2 + bakercp/CRC32 @ ^2.0.0 + +[env:WioTrackerL1Eink_companion_radio_ble] +extends = WioTrackerL1Eink +board_build.ldscript = boards/nrf52840_s140_v7_extrafs.ld +board_upload.maximum_size = 708608 +build_flags = ${WioTrackerL1Eink.build_flags} + -I examples/companion_radio/ui-new + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D BLE_PIN_CODE=123456 + -D BLE_DEBUG_LOGGING=1 + -D OFFLINE_QUEUE_SIZE=256 + -D DISPLAY_CLASS=GxEPDDisplay + -D UI_HAS_JOYSTICK=1 + -D PIN_BUZZER=12 + -D QSPIFLASH=1 + -D UI_RECENT_LIST_SIZE=6 + -D UI_SENSORS_PAGE=1 +build_src_filter = ${WioTrackerL1Eink.build_src_filter} + + + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = ${WioTrackerL1Eink.lib_deps} + adafruit/RTClib @ ^2.1.3 + densaugeo/base64 @ ~1.4.0 + end2endzone/NonBlockingRTTTL@^1.3.0 +debug_tool = stlink + +[env:WioTrackerL1Eink_kiss_modem] +extends = WioTrackerL1Eink +build_src_filter = ${WioTrackerL1Eink.build_src_filter} + +<../examples/kiss_modem/> + +[Mesh_pocket] +extends = nrf52_base +board = heltec_mesh_pocket +board_build.ldscript = boards/nrf52840_s140_v6.ld +build_flags = ${nrf52_base.build_flags} + -I src/helpers/nrf52 + -I lib/nrf52/s140_nrf52_6.1.1_API/include + -I lib/nrf52/s140_nrf52_6.1.1_API/include/nrf52 + -I variants/mesh_pocket + -D HELTEC_MESH_POCKET + -D RADIO_CLASS=CustomSX1262 + -D WRAPPER_CLASS=CustomSX1262Wrapper + -D LORA_TX_POWER=22 + -D SX126X_CURRENT_LIMIT=140 + -D SX126X_RX_BOOSTED_GAIN=1 + -D EINK_DISPLAY_MODEL=GxEPD2_213_B74 + -D EINK_SCALE_X=1.953125f + -D EINK_SCALE_Y=1.28f + -D EINK_X_OFFSET=0 + -D EINK_Y_OFFSET=10 + -D DISPLAY_CLASS=GxEPDDisplay + -D DISABLE_DIAGNOSTIC_OUTPUT +build_src_filter = ${nrf52_base.build_src_filter} + + + +<../variants/mesh_pocket> + + +lib_deps = + ${nrf52_base.lib_deps} + adafruit/Adafruit EPD @ 4.6.1 + rweather/Crypto @ ^0.4.0 + stevemarple/MicroNMEA @ ^2.0.6 + zinggjm/GxEPD2 @ 1.6.2 + bakercp/CRC32 @ ^2.0.0 +debug_tool = jlink +upload_protocol = nrfutil + +[env:Mesh_pocket_repeater] +extends = Mesh_pocket +build_src_filter = ${Mesh_pocket.build_src_filter} + +<../examples/simple_repeater> +build_flags = + ${Mesh_pocket.build_flags} + -D ADVERT_NAME='"Heltec_Mesh_Pocket Repeater"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 + +[env:Mesh_pocket_room_server] +extends = Mesh_pocket +build_src_filter = ${Mesh_pocket.build_src_filter} + +<../examples/simple_room_server> +build_flags = + ${Mesh_pocket.build_flags} + -D ADVERT_NAME='"Heltec_Mesh_Pocket Room"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D ROOM_PASSWORD='"hello"' + +[env:Mesh_pocket_companion_radio_ble] +extends = Mesh_pocket +board_build.ldscript = boards/nrf52840_s140_v6_extrafs.ld +board_upload.maximum_size = 712704 +build_flags = + ${Mesh_pocket.build_flags} + -I examples/companion_radio/ui-new + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D BLE_PIN_CODE=123456 + -D OFFLINE_QUEUE_SIZE=256 + -D AUTO_OFF_MILLIS=0 +build_src_filter = ${Mesh_pocket.build_src_filter} + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${Mesh_pocket.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:Mesh_pocket_companion_radio_usb] +extends = Mesh_pocket +board_build.ldscript = boards/nrf52840_s140_v6_extrafs.ld +board_upload.maximum_size = 712704 +build_flags = + ${Mesh_pocket.build_flags} + -I examples/companion_radio/ui-new + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D AUTO_OFF_MILLIS=0 + -D ENABLE_USB_INTERFACE +build_src_filter = ${Mesh_pocket.build_src_filter} + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${Mesh_pocket.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:Mesh_pocket_kiss_modem] +extends = Mesh_pocket +build_src_filter = ${Mesh_pocket.build_src_filter} + +<../examples/kiss_modem/> + +[LilyGo_TDeck] +extends = esp32_base +board = t-deck +build_flags = + ${esp32_base.build_flags} + ${sensor_base.build_flags} + -I variants/lilygo_tdeck + -D LILYGO_TDECK + -D BOARD_HAS_PSRAM=1 + -D CORE_DEBUG_LEVEL=1 + -D ARDUINO_USB_CDC_ON_BOOT=1 + -D PIN_USER_BTN=0 + -D PIN_PERF_POWERON=10 + -D USE_SX1262 + -D RADIO_CLASS=CustomSX1262 + -D WRAPPER_CLASS=CustomSX1262Wrapper + -D LORA_TX_POWER=22 + -D SX126X_DIO2_AS_RF_SWITCH=false + -D SX126X_CURRENT_LIMIT=140 + -D SX126X_RX_BOOSTED_GAIN=1 + -D SX126X_DIO3_TCXO_VOLTAGE=1.8f + -D P_LORA_DIO_1=45 + -D ENV_INCLUDE_GPS=1 + -D ENV_INCLUDE_AHTX0=0 + -D ENV_INCLUDE_BME280=0 + -D ENV_INCLUDE_BMP280=0 + -D ENV_INCLUDE_SHTC3=0 + -D ENV_INCLUDE_SHT4X=0 + -D ENV_INCLUDE_LPS22HB=0 + -D ENV_INCLUDE_INA3221=0 + -D ENV_INCLUDE_INA219=0 + -D ENV_INCLUDE_INA226=0 + -D ENV_INCLUDE_INA260=0 + -D ENV_INCLUDE_MLX90614=0 + -D ENV_INCLUDE_VL53L0X=0 + -D ENV_INCLUDE_BME680=0 + -D ENV_INCLUDE_BMP085=0 + -D P_LORA_NSS=9 + -D P_LORA_RESET=17 + -D P_LORA_BUSY=13 + -D P_LORA_SCLK=40 + -D P_LORA_MISO=38 + -D P_LORA_MOSI=41 + -D DISPLAY_CLASS=ST7789LCDDisplay + -D DISPLAY_SCALE_X=2.5 + -D DISPLAY_SCALE_Y=3.75 + -D PIN_TFT_RST=-1 + -D PIN_TFT_VDD_CTL=-1 + -D PIN_TFT_LEDA_CTL=42 + -D PIN_TFT_CS=12 + -D PIN_TFT_DC=11 + -D PIN_TFT_SCL=40 + -D PIN_TFT_SDA=41 + -D PIN_GPS_RX=43 + -D PIN_GPS_TX=44 + -D GPS_BAUD_RATE=38400 +build_src_filter = ${esp32_base.build_src_filter} + +<../variants/lilygo_tdeck> + + + + +lib_deps = + ${esp32_base.lib_deps} + ${sensor_base.lib_deps} + adafruit/Adafruit ST7735 and ST7789 Library @ ^1.11.0 + +[env:LilyGo_TDeck_companion_radio_usb] +extends = LilyGo_TDeck +build_flags = + ${LilyGo_TDeck.build_flags} + -I examples/companion_radio/ui-new + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D OFFLINE_QUEUE_SIZE=256 + -D ENABLE_USB_INTERFACE +build_src_filter = ${LilyGo_TDeck.build_src_filter} + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${LilyGo_TDeck.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:LilyGo_TDeck_companion_radio_ble] +extends = LilyGo_TDeck +build_flags = + ${LilyGo_TDeck.build_flags} + -I examples/companion_radio/ui-new + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D BLE_PIN_CODE=123456 + -D OFFLINE_QUEUE_SIZE=256 +build_src_filter = ${LilyGo_TDeck.build_src_filter} + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${LilyGo_TDeck.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:LilyGo_TDeck_repeater] +extends = LilyGo_TDeck +build_flags = + ${LilyGo_TDeck.build_flags} + -D ADVERT_NAME='"TDeck Repeater"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 +build_src_filter = ${LilyGo_TDeck.build_src_filter} + +<../examples/simple_repeater> + + +lib_deps = + ${LilyGo_TDeck.lib_deps} + ${esp32_ota.lib_deps} + +[env:LilyGo_TDeck_kiss_modem] +extends = LilyGo_TDeck +build_src_filter = ${LilyGo_TDeck.build_src_filter} + +<../examples/kiss_modem/> + +[Station_G2] +extends = esp32_base +board = station-g2 +build_flags = + ${esp32_base.build_flags} + ${sensor_base.build_flags} + -I variants/station_g2 + -I src/helpers/ui + -D STATION_G2 + -D USE_SX1262 + -D RADIO_CLASS=CustomSX1262 + -D WRAPPER_CLASS=CustomSX1262Wrapper + -D P_LORA_DIO_1=48 + -D P_LORA_NSS=11 + -D P_LORA_RESET=21 + -D P_LORA_BUSY=47 + -D P_LORA_SCLK=12 + -D P_LORA_MISO=14 + -D P_LORA_MOSI=13 + -D LORA_TX_POWER=7 + -D MAX_LORA_TX_POWER=19 + -D PIN_BOARD_SDA=5 + -D PIN_BOARD_SCL=6 + -D PIN_USER_BTN=38 + -D PIN_GPS_RX=15 + -D PIN_GPS_TX=7 + -D SX126X_DIO2_AS_RF_SWITCH=true + -D SX126X_DIO3_TCXO_VOLTAGE=1.8 + -D SX126X_CURRENT_LIMIT=140 + -D SX126X_RX_BOOSTED_GAIN=0 + -D DISPLAY_CLASS=SH1106Display +build_src_filter = ${esp32_base.build_src_filter} + +<../variants/station_g2> + + + + + + +lib_deps = + ${esp32_base.lib_deps} + ${sensor_base.lib_deps} + adafruit/Adafruit SH110X @ ~2.1.13 + adafruit/Adafruit GFX Library @ ^1.12.1 + +[env:Station_G2_repeater] +extends = Station_G2 +build_flags = + ${Station_G2.build_flags} + -D ADVERT_NAME='"Station G2 Repeater"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 +build_src_filter = ${Station_G2.build_src_filter} + +<../examples/simple_repeater> +lib_deps = + ${Station_G2.lib_deps} + ${esp32_ota.lib_deps} + +[env:Station_G2_repeater_bridge_espnow] +extends = Station_G2 +build_flags = + ${Station_G2.build_flags} + -D ADVERT_NAME='"ESPNow Bridge"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 + -D WITH_ESPNOW_BRIDGE=1 +build_src_filter = ${Station_G2.build_src_filter} + + + +<../examples/simple_repeater> +lib_deps = + ${Station_G2.lib_deps} + ${esp32_ota.lib_deps} + +[env:Station_G2_logging_repeater] +extends = Station_G2 +build_flags = + ${Station_G2.build_flags} + -D ADVERT_NAME='"Station G2 Logging Repeater"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 + -D SX126X_RX_BOOSTED_GAIN=1 +build_src_filter = ${Station_G2.build_src_filter} + +<../examples/simple_repeater> +lib_deps = + ${Station_G2.lib_deps} + ${esp32_ota.lib_deps} + +[env:Station_G2_logging_repeater_bridge_espnow] +extends = Station_G2 +build_flags = + ${Station_G2.build_flags} + -D ADVERT_NAME='"ESPNow Bridge"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 + -D SX126X_RX_BOOSTED_GAIN=1 + -D WITH_ESPNOW_BRIDGE=1 +build_src_filter = ${Station_G2.build_src_filter} + + + +<../examples/simple_repeater> +lib_deps = + ${Station_G2.lib_deps} + ${esp32_ota.lib_deps} + +[env:Station_G2_room_server] +extends = Station_G2 +build_src_filter = ${Station_G2.build_src_filter} + +<../examples/simple_room_server> +build_flags = + ${Station_G2.build_flags} + -D ADVERT_NAME='"Station G2 Room"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D ROOM_PASSWORD='"hello"' +lib_deps = + ${Station_G2.lib_deps} + ${esp32_ota.lib_deps} + +[env:Station_G2_companion_radio_usb] +extends = Station_G2 +build_flags = + ${Station_G2.build_flags} + -I examples/companion_radio/ui-new + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D ENABLE_USB_INTERFACE +build_src_filter = ${Station_G2.build_src_filter} + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${Station_G2.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:Station_G2_companion_radio_ble] +extends = Station_G2 +build_flags = + ${Station_G2.build_flags} + -I examples/companion_radio/ui-new + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D BLE_PIN_CODE=123456 + -D BLE_DEBUG_LOGGING=1 + -D OFFLINE_QUEUE_SIZE=256 +build_src_filter = ${Station_G2.build_src_filter} + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${Station_G2.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:Station_G2_companion_radio_wifi] +extends = Station_G2 +build_flags = + ${Station_G2.build_flags} + -I examples/companion_radio/ui-new + -D ENABLE_WIFI_INTERFACE + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D WIFI_DEBUG_LOGGING=1 + -D WIFI_SSID='"myssid"' + -D WIFI_PWD='"mypwd"' + -D OFFLINE_QUEUE_SIZE=256 +build_src_filter = ${Station_G2.build_src_filter} + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${Station_G2.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:Station_G2_kiss_modem] +extends = Station_G2 +build_flags = + ${Station_G2.build_flags} + -D ARDUINO_USB_MODE=1 +build_src_filter = ${Station_G2.build_src_filter} + +<../examples/kiss_modem/> + +[rak_wismesh_tag] +extends = nrf52_base +board = rak4631 +board_check = true +build_flags = ${nrf52_base.build_flags} + ${sensor_base.build_flags} + -I variants/rak_wismesh_tag + -I src/helpers/ui + -D RAK_WISMESH_TAG + -D RAK_BOARD + -D P_LORA_TX_LED=LED_GREEN + -D P_LORA_DIO_1=SX126X_DIO1 + -D P_LORA_NSS=PIN_SPI_NSS + -D P_LORA_RESET=SX126X_RESET + -D P_LORA_BUSY=SX126X_BUSY + -D P_LORA_SCLK=PIN_SPI_SCK + -D P_LORA_MISO=PIN_SPI_MISO + -D P_LORA_MOSI=PIN_SPI_MOSI + -D RADIO_CLASS=CustomSX1262 + -D WRAPPER_CLASS=CustomSX1262Wrapper + -D DISPLAY_CLASS=NullDisplayDriver + -D LORA_TX_POWER=22 + -D SX126X_CURRENT_LIMIT=140 + -D SX126X_RX_BOOSTED_GAIN=1 + -D PIN_BUZZER=21 + -D PIN_BOARD_SDA=PIN_WIRE_SDA + -D PIN_BOARD_SCL=PIN_WIRE_SCL +build_src_filter = ${nrf52_base.build_src_filter} + +<../variants/rak_wismesh_tag> + + + + + + +lib_deps = + ${nrf52_base.lib_deps} + ${sensor_base.lib_deps} + +[env:RAK_WisMesh_Tag_repeater] +extends = rak_wismesh_tag +build_flags = + ${rak_wismesh_tag.build_flags} + -D ADVERT_NAME='"RAK WM Repeater"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 +build_src_filter = ${rak_wismesh_tag.build_src_filter} + +<../examples/simple_repeater> + +[env:RAK_WisMesh_Tag_room_server] +extends = rak_wismesh_tag +build_flags = + ${rak_wismesh_tag.build_flags} + -D ADVERT_NAME='"RAK WM Room"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D ROOM_PASSWORD='"hello"' +build_src_filter = ${rak_wismesh_tag.build_src_filter} + +<../examples/simple_room_server> + +[env:RAK_WisMesh_Tag_companion_radio_usb] +extends = rak_wismesh_tag +board_build.ldscript = boards/nrf52840_s140_v6_extrafs.ld +board_upload.maximum_size = 712704 +build_flags = + ${rak_wismesh_tag.build_flags} + -I examples/companion_radio/ui-orig + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D ENABLE_USB_INTERFACE +build_src_filter = ${rak_wismesh_tag.build_src_filter} + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-orig/*.cpp> +lib_deps = + ${rak_wismesh_tag.lib_deps} + densaugeo/base64 @ ~1.4.0 + end2endzone/NonBlockingRTTTL@^1.3.0 + +[env:RAK_WisMesh_Tag_companion_radio_ble] +extends = rak_wismesh_tag +board_build.ldscript = boards/nrf52840_s140_v6_extrafs.ld +board_upload.maximum_size = 712704 +build_flags = + ${rak_wismesh_tag.build_flags} + -I examples/companion_radio/ui-orig + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D BLE_PIN_CODE=123456 + -D BLE_DEBUG_LOGGING=1 + -D OFFLINE_QUEUE_SIZE=256 + -D PIN_GPS_EN=34 +build_src_filter = ${rak_wismesh_tag.build_src_filter} + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-orig/*.cpp> +lib_deps = + ${rak_wismesh_tag.lib_deps} + densaugeo/base64 @ ~1.4.0 + end2endzone/NonBlockingRTTTL@^1.3.0 + +[env:RAK_WisMesh_Tag_sensor] +extends = rak_wismesh_tag +build_flags = + ${rak_wismesh_tag.build_flags} + -D ADVERT_NAME='"RAK WM Sensor"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' +build_src_filter = ${rak_wismesh_tag.build_src_filter} + +<../examples/simple_sensor> + +[env:RAK_WisMesh_Tag_kiss_modem] +extends = rak_wismesh_tag +build_src_filter = ${rak_wismesh_tag.build_src_filter} + +<../examples/kiss_modem/> + +[rak11310] +extends = rp2040_base +board = rakwireless_rak11300 +board_build.filesystem_size = 0.5m +build_flags = ${rp2040_base.build_flags} + -I variants/rak11310 + -D RAK_11310 + -D ARDUINO_RAKWIRELESS_RAK11300=1 + -D SX126X_CURRENT_LIMIT=140 + -D USE_SX1262 + -D RADIO_CLASS=CustomSX1262 + -D WRAPPER_CLASS=CustomSX1262Wrapper + -D P_LORA_DIO_1=29 + -D P_LORA_NSS=13 + -D P_LORA_RESET=14 + -D P_LORA_BUSY=15 + -D P_LORA_SCLK=10 + -D P_LORA_MISO=12 + -D P_LORA_MOSI=11 + -D P_LORA_TX_LED=24 + -D SX126X_DIO2_AS_RF_SWITCH=true + -D SX126X_DIO3_TCXO_VOLTAGE=1.8 + -D SX126X_RX_BOOSTED_GAIN=1 + -D LORA_TX_POWER=22 +build_src_filter = ${rp2040_base.build_src_filter} + + + +<../variants/rak11310> +lib_deps = ${rp2040_base.lib_deps} + +[env:RAK_11310_repeater] +extends = rak11310 +build_flags = ${rak11310.build_flags} + -D ADVERT_NAME='"RAK11310 Repeater"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 +build_src_filter = ${rak11310.build_src_filter} + +<../examples/simple_repeater> + +[env:RAK_11310_repeater_bridge_rs232] +extends = rak11310 +build_flags = ${rak11310.build_flags} + -D ADVERT_NAME='"RS232 Bridge"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 + -D WITH_RS232_BRIDGE=Serial2 + -D WITH_RS232_BRIDGE_RX=9 + -D WITH_RS232_BRIDGE_TX=8 +build_src_filter = ${rak11310.build_src_filter} + + + +<../examples/simple_repeater> + +[env:RAK_11310_room_server] +extends = rak11310 +build_flags = ${rak11310.build_flags} + -D ADVERT_NAME='"RAK11310 Room"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D ROOM_PASSWORD='"hello"' +build_src_filter = ${rak11310.build_src_filter} + +<../examples/simple_room_server> + +[env:RAK_11310_companion_radio_usb] +extends = rak11310 +build_flags = ${rak11310.build_flags} + -D MAX_CONTACTS=100 + -D MAX_GROUP_CHANNELS=8 + -D ENABLE_USB_INTERFACE +build_src_filter = ${rak11310.build_src_filter} + +<../examples/companion_radio/*.cpp> +lib_deps = ${rak11310.lib_deps} + densaugeo/base64 @ ~1.4.0 +lib_ignore = BLE + +[env:RAK_11310_terminal_chat] +extends = rak11310 +build_flags = ${rak11310.build_flags} + -D MAX_CONTACTS=100 + -D MAX_GROUP_CHANNELS=1 +build_src_filter = ${rak11310.build_src_filter} + +<../examples/simple_secure_chat/main.cpp> +lib_deps = ${rak11310.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:RAK_11310_kiss_modem] +extends = rak11310 +build_src_filter = ${rak11310.build_src_filter} + +<../examples/kiss_modem/> + +[rpi_picow] +extends = rp2040_base +board = rpipicow +board_build.core = earlephilhower +board_build.filesystem_size = 0.5m +build_flags = ${rp2040_base.build_flags} + -I variants/rpi_picow + -D P_LORA_DIO_1=20 + -D P_LORA_NSS=3 + -D P_LORA_RESET=15 + -D P_LORA_BUSY=2 + -D P_LORA_SCLK=10 + -D P_LORA_MISO=12 + -D P_LORA_MOSI=11 + -D SX126X_DIO2_AS_RF_SWITCH=true + -D SX126X_DIO3_TCXO_VOLTAGE=1.8 + -D SX126X_CURRENT_LIMIT=130 + -D SX126X_RX_BOOSTED_GAIN=1 + -D LORA_TX_POWER=22 + -D USE_SX1262 + -D RADIO_CLASS=CustomSX1262 + -D WRAPPER_CLASS=CustomSX1262Wrapper +build_src_filter = ${rp2040_base.build_src_filter} + + + +<../variants/rpi_picow> +lib_deps = ${rp2040_base.lib_deps} + +[env:PicoW_repeater] +extends = rpi_picow +build_flags = ${rpi_picow.build_flags} + -D ADVERT_NAME='"PicoW Repeater"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 +build_src_filter = ${rpi_picow.build_src_filter} + +<../examples/simple_repeater> + +[env:PicoW_room_server] +extends = rpi_picow +build_flags = ${rpi_picow.build_flags} + -D ADVERT_NAME='"Test Room"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D ROOM_PASSWORD='"hello"' +build_src_filter = ${rpi_picow.build_src_filter} + +<../examples/simple_room_server> + +[env:PicoW_companion_radio_usb] +extends = rpi_picow +build_flags = ${rpi_picow.build_flags} + -D MAX_CONTACTS=100 + -D MAX_GROUP_CHANNELS=8 + -D ENABLE_USB_INTERFACE +build_src_filter = ${rpi_picow.build_src_filter} + +<../examples/companion_radio/*.cpp> +lib_deps = ${rpi_picow.lib_deps} + densaugeo/base64 @ ~1.4.0 +lib_ignore = BLE + +[env:PicoW_companion_radio_ble] +extends = rpi_picow +build_flags = ${rpi_picow.build_flags} + -D MAX_CONTACTS=100 + -D MAX_GROUP_CHANNELS=8 + -D PIO_FRAMEWORK_ARDUINO_ENABLE_BLUETOOTH + -D BLE_PIN_CODE=123456 + -D BLE_DEBUG_LOGGING=1 +build_src_filter = ${rpi_picow.build_src_filter} + + + +<../examples/companion_radio/*.cpp> +lib_deps = ${rpi_picow.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:PicoW_companion_radio] +extends = rpi_picow +build_flags = ${rpi_picow.build_flags} + -D MAX_CONTACTS=100 + -D MAX_GROUP_CHANNELS=8 + -D ENABLE_USB_INTERFACE + -D ENABLE_WIFI_INTERFACE + -D PIO_FRAMEWORK_ARDUINO_ENABLE_BLUETOOTH + -D BLE_PIN_CODE=123456 +build_src_filter = ${rpi_picow.build_src_filter} + + + + + +<../examples/companion_radio/*.cpp> +lib_deps = ${rpi_picow.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:PicoW_companion_radio_wifi] +extends = rpi_picow +build_flags = ${rpi_picow.build_flags} + -D ENABLE_WIFI_INTERFACE + -D MAX_CONTACTS=100 + -D MAX_GROUP_CHANNELS=8 + -D WIFI_DEBUG_LOGGING=1 + -D WIFI_SSID='""' + -D WIFI_PWD='""' +build_src_filter = ${rpi_picow.build_src_filter} + + + +<../examples/companion_radio/*.cpp> +lib_deps = ${rpi_picow.lib_deps} + densaugeo/base64 @ ~1.4.0 +lib_ignore = BLE + +[env:PicoW_terminal_chat] +extends = rpi_picow +build_flags = ${rpi_picow.build_flags} + -D MAX_CONTACTS=100 + -D MAX_GROUP_CHANNELS=1 +build_src_filter = ${rpi_picow.build_src_filter} + +<../examples/simple_secure_chat/main.cpp> +lib_deps = ${rpi_picow.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:PicoW_kiss_modem] +extends = rpi_picow +build_src_filter = ${rpi_picow.build_src_filter} + +<../examples/kiss_modem/> + +[LilyGo_T3S3_sx1262] +extends = esp32_base +board = t3_s3_v1_x +build_flags = + ${esp32_base.build_flags} + -I variants/lilygo_t3s3 + -D LILYGO_T3S3 + -D P_LORA_DIO_1=33 + -D P_LORA_NSS=7 + -D P_LORA_RESET=8 + -D P_LORA_BUSY=34 + -D P_LORA_SCLK=5 + -D P_LORA_MISO=3 + -D P_LORA_MOSI=6 + -D P_LORA_TX_LED=37 + -D PIN_VBAT_READ=1 + -D PIN_USER_BTN=0 + -D PIN_BOARD_SDA=18 + -D PIN_BOARD_SCL=17 + -D P_LORA_TX_LED=37 + -D PIN_OLED_RESET=21 + -D SX126X_DIO2_AS_RF_SWITCH=true + -D SX126X_DIO3_TCXO_VOLTAGE=1.8 + -D SX126X_CURRENT_LIMIT=140 + -D USE_SX1262 + -D RADIO_CLASS=CustomSX1262 + -D WRAPPER_CLASS=CustomSX1262Wrapper + -D LORA_TX_POWER=22 + -D SX126X_RX_BOOSTED_GAIN=1 +build_src_filter = ${esp32_base.build_src_filter} + +<../variants/lilygo_t3s3> +lib_deps = + ${esp32_base.lib_deps} + adafruit/Adafruit SSD1306 @ ^2.5.13 + +[env:LilyGo_T3S3_sx1262_repeater] +extends = LilyGo_T3S3_sx1262 +build_flags = + ${LilyGo_T3S3_sx1262.build_flags} + -D DISPLAY_CLASS=SSD1306Display + -D ADVERT_NAME='"T3S3-1262 Repeater"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 +build_src_filter = ${LilyGo_T3S3_sx1262.build_src_filter} + + + +<../examples/simple_repeater> +lib_deps = + ${LilyGo_T3S3_sx1262.lib_deps} + ${esp32_ota.lib_deps} + +[env:LilyGo_T3S3_sx1262_repeater_bridge_espnow] +extends = LilyGo_T3S3_sx1262 +build_flags = + ${LilyGo_T3S3_sx1262.build_flags} + -D DISPLAY_CLASS=SSD1306Display + -D ADVERT_NAME='"ESPNow Bridge"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 + -D WITH_ESPNOW_BRIDGE=1 +build_src_filter = ${LilyGo_T3S3_sx1262.build_src_filter} + + + + + +<../examples/simple_repeater> +lib_deps = + ${LilyGo_T3S3_sx1262.lib_deps} + ${esp32_ota.lib_deps} + +[env:LilyGo_T3S3_sx1262_terminal_chat] +extends = LilyGo_T3S3_sx1262 +build_flags = + ${LilyGo_T3S3_sx1262.build_flags} + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=1 +build_src_filter = ${LilyGo_T3S3_sx1262.build_src_filter} + +<../examples/simple_secure_chat/main.cpp> +lib_deps = + ${LilyGo_T3S3_sx1262.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:LilyGo_T3S3_sx1262_room_server] +extends = LilyGo_T3S3_sx1262 +build_flags = + ${LilyGo_T3S3_sx1262.build_flags} + -D DISPLAY_CLASS=SSD1306Display + -D ADVERT_NAME='"T3S3-1262 Room"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D ROOM_PASSWORD='"hello"' +build_src_filter = ${LilyGo_T3S3_sx1262.build_src_filter} + + + +<../examples/simple_room_server> +lib_deps = + ${LilyGo_T3S3_sx1262.lib_deps} + ${esp32_ota.lib_deps} + +[env:LilyGo_T3S3_sx1262_companion_radio_usb] +extends = LilyGo_T3S3_sx1262 +build_flags = + ${LilyGo_T3S3_sx1262.build_flags} + -I examples/companion_radio/ui-new + -D DISPLAY_CLASS=SSD1306Display + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D ENABLE_USB_INTERFACE +build_src_filter = ${LilyGo_T3S3_sx1262.build_src_filter} + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${LilyGo_T3S3_sx1262.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:LilyGo_T3S3_sx1262_companion_radio_ble] +extends = LilyGo_T3S3_sx1262 +build_flags = + ${LilyGo_T3S3_sx1262.build_flags} + -I examples/companion_radio/ui-new + -D DISPLAY_CLASS=SSD1306Display + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D BLE_PIN_CODE=123456 + -D BLE_DEBUG_LOGGING=1 + -D OFFLINE_QUEUE_SIZE=256 +build_src_filter = ${LilyGo_T3S3_sx1262.build_src_filter} + + + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${LilyGo_T3S3_sx1262.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:LilyGo_T3S3_sx1262_kiss_modem] +extends = LilyGo_T3S3_sx1262 +build_src_filter = ${LilyGo_T3S3_sx1262.build_src_filter} + +<../examples/kiss_modem/> + +[MeshTracker_X1] +extends = nrf52_base +board = seeed-mesh-tracker-x1 +board_build.ldscript = boards/nrf52840_s140_v7.ld +build_flags = ${nrf52_base.build_flags} + -I src/helpers/nrf52 + -I lib/nrf52/s140_nrf52_7.3.0_API/include + -I lib/nrf52/s140_nrf52_7.3.0_API/include/nrf52 + -I variants/meshtracker_x1 + -I src/helpers/ui + -D MESH_TRACKER_X1 + -D PIN_USER_BTN=6 + -D USER_BTN_PRESSED=HIGH + -D PIN_STATUS_LED=24 + -D PIN_STATUS_LED_R=3 + -D PIN_STATUS_LED_G=24 + -D PIN_STATUS_LED_B=28 + -D RADIO_CLASS=CustomLR2021 + -D USE_LR2021 + -D WRAPPER_CLASS=CustomLR2021Wrapper + -D LORA_TX_POWER=22 + -D P_LORA_BUSY=7 + -D P_LORA_SCLK=11 + -D P_LORA_NSS=12 + -D P_LORA_DIO_1=33 + -D P_LORA_MISO=40 + -D P_LORA_MOSI=41 + -D P_LORA_RESET=42 + -D LR2021_IRQ_DIO=8 + -D LR2021_TCXO_VOLTAGE=1.6f + -D ENV_INCLUDE_GPS=1 +build_src_filter = ${nrf52_base.build_src_filter} + + + +<../variants/meshtracker_x1> +lib_deps = ${nrf52_base.lib_deps} + https://github.com/adafruit/Adafruit_SPA06_003/archive/refs/tags/1.0.2.zip +debug_tool = jlink +upload_protocol = nrfutil + +[env:MeshTracker_X1_repeater] +extends = MeshTracker_X1 +build_flags = ${MeshTracker_X1.build_flags} + -I examples/companion_radio/ui-orig + -D ADVERT_NAME='"MeshTracker X1 Repeater"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 +build_src_filter = ${MeshTracker_X1.build_src_filter} + +<../examples/simple_repeater> +lib_deps = ${MeshTracker_X1.lib_deps} + stevemarple/MicroNMEA @ ^2.0.6 + +[env:MeshTracker_X1_room_server] +extends = MeshTracker_X1 +build_flags = ${MeshTracker_X1.build_flags} + -I examples/companion_radio/ui-orig + -D ADVERT_NAME='"MeshTracker X1 Room"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D ROOM_PASSWORD='"hello"' +build_src_filter = ${MeshTracker_X1.build_src_filter} + +<../examples/simple_room_server> +lib_deps = ${MeshTracker_X1.lib_deps} + stevemarple/MicroNMEA @ ^2.0.6 + +[env:MeshTracker_X1_companion_radio_usb] +extends = MeshTracker_X1 +board_build.ldscript = boards/nrf52840_s140_v7_extrafs.ld +board_upload.maximum_size = 708608 +build_flags = ${MeshTracker_X1.build_flags} + -I examples/companion_radio/ui-orig + -D QSPIFLASH=1 + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D OFFLINE_QUEUE_SIZE=256 + -D DISPLAY_CLASS=NullDisplayDriver + -D PIN_BUZZER=25 + -D HAS_DRV2605=1 + -D DRV2605_USE_LRA=1 + -D ENABLE_USB_INTERFACE +build_src_filter = ${MeshTracker_X1.build_src_filter} + + + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-orig/*.cpp> +lib_deps = ${MeshTracker_X1.lib_deps} + densaugeo/base64 @ ~1.4.0 + stevemarple/MicroNMEA @ ^2.0.6 + end2endzone/NonBlockingRTTTL@^1.3.0 + adafruit/Adafruit DRV2605 Library @ ^1.2.4 + +[env:MeshTracker_X1_companion_radio_ble] +extends = MeshTracker_X1 +board_build.ldscript = boards/nrf52840_s140_v7_extrafs.ld +board_upload.maximum_size = 708608 +build_flags = ${MeshTracker_X1.build_flags} + -I examples/companion_radio/ui-orig + -D QSPIFLASH=1 + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D BLE_PIN_CODE=123456 + -D BLE_TX_POWER=0 + -D OFFLINE_QUEUE_SIZE=256 + -D DISPLAY_CLASS=NullDisplayDriver + -D PIN_BUZZER=25 + -D HAS_DRV2605=1 + -D DRV2605_USE_LRA=1 + -D ADVERT_NAME='"@@MAC"' +build_src_filter = ${MeshTracker_X1.build_src_filter} + + + + + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-orig/*.cpp> +lib_deps = ${MeshTracker_X1.lib_deps} + densaugeo/base64 @ ~1.4.0 + stevemarple/MicroNMEA @ ^2.0.6 + end2endzone/NonBlockingRTTTL@^1.3.0 + adafruit/Adafruit DRV2605 Library @ ^1.2.4 + +[env:MeshTracker_X1_kiss_modem] +extends = MeshTracker_X1 +build_src_filter = ${MeshTracker_X1.build_src_filter} + +<../examples/kiss_modem/> + +[rak3401] +extends = nrf52_base +board = rak3401 +board_check = true +build_flags = ${nrf52_base.build_flags} + ${sensor_base.build_flags} + -I variants/rak3401 + -D RAK_3401 + -D RAK_BOARD + -D RADIO_CLASS=CustomSX1262 + -D WRAPPER_CLASS=CustomSX1262Wrapper + -D LORA_TX_POWER=22 + -D SX126X_CURRENT_LIMIT=140 + -D SX126X_RX_BOOSTED_GAIN=1 + -D SX126X_REGISTER_PATCH=1 +build_src_filter = ${nrf52_base.build_src_filter} + +<../variants/rak3401> + + + + + + +lib_deps = + ${nrf52_base.lib_deps} + ${sensor_base.lib_deps} + adafruit/Adafruit SSD1306 @ ^2.5.13 + sparkfun/SparkFun u-blox GNSS Arduino Library@^2.2.27 + +[env:RAK_3401_repeater] +extends = rak3401 +build_flags = + ${rak3401.build_flags} + -D DISPLAY_CLASS=SSD1306Display + -D ADVERT_NAME='"RAK3401 1W Repeater"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 +build_src_filter = ${rak3401.build_src_filter} + + + +<../examples/simple_repeater> + +[env:RAK_3401_room_server] +extends = rak3401 +build_flags = + ${rak3401.build_flags} + -D DISPLAY_CLASS=SSD1306Display + -D ADVERT_NAME='"Test Room"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D ROOM_PASSWORD='"hello"' +build_src_filter = ${rak3401.build_src_filter} + + + +<../examples/simple_room_server> + +[env:RAK_3401_companion_radio_usb] +extends = rak3401 +board_build.ldscript = boards/nrf52840_s140_v6_extrafs.ld +board_upload.maximum_size = 712704 +build_flags = + ${rak3401.build_flags} + -I examples/companion_radio/ui-new + -D PIN_USER_BTN_ANA=31 + -D DISPLAY_CLASS=SSD1306Display + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D ENABLE_USB_INTERFACE +build_src_filter = ${rak3401.build_src_filter} + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${rak3401.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:RAK_3401_companion_radio_ble] +extends = rak3401 +board_build.ldscript = boards/nrf52840_s140_v6_extrafs.ld +board_upload.maximum_size = 712704 +build_flags = + ${rak3401.build_flags} + -I examples/companion_radio/ui-new + -D PIN_USER_BTN_ANA=31 + -D DISPLAY_CLASS=SSD1306Display + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D BLE_PIN_CODE=123456 + -D BLE_DEBUG_LOGGING=1 + -D OFFLINE_QUEUE_SIZE=256 +build_src_filter = ${rak3401.build_src_filter} + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${rak3401.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:RAK_3401_terminal_chat] +extends = rak3401 +build_flags = + ${rak3401.build_flags} + -D MAX_CONTACTS=100 + -D MAX_GROUP_CHANNELS=1 +build_src_filter = ${rak3401.build_src_filter} + +<../examples/simple_secure_chat/main.cpp> +lib_deps = + ${rak3401.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:RAK_3401_sensor] +extends = rak3401 +build_flags = + ${rak3401.build_flags} + -D DISPLAY_CLASS=SSD1306Display + -D ADVERT_NAME='"RAK3401 Sensor"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' +build_src_filter = ${rak3401.build_src_filter} + + + +<../examples/simple_sensor> + +[env:RAK_3401_kiss_modem] +extends = rak3401 +build_src_filter = ${rak3401.build_src_filter} + +<../examples/kiss_modem/> + +[ikoka_stick_nrf] +extends = nrf52_base +board = seeed-xiao-afruitnrf52-nrf52840 +board_build.ldscript = boards/nrf52840_s140_v7.ld +build_flags = ${nrf52_base.build_flags} + ${sensor_base.build_flags} + -D NRF52_PLATFORM -D XIAO_NRF52 + -I lib/nrf52/s140_nrf52_7.3.0_API/include + -I lib/nrf52/s140_nrf52_7.3.0_API/include/nrf52 + -I variants/ikoka_stick_nrf + -I src/helpers/nrf52 + -D P_LORA_TX_LED=11 + -D DISPLAY_CLASS=SSD1306Display + -D DISPLAY_ROTATION=2 + -D USE_SX1262 + -D RADIO_CLASS=CustomSX1262 + -D WRAPPER_CLASS=CustomSX1262Wrapper + -D P_LORA_DIO_1=D1 + -D P_LORA_RESET=D2 + -D P_LORA_BUSY=D3 + -D P_LORA_NSS=D4 + -D SX126X_RXEN=D5 + -D SX126X_TXEN=RADIOLIB_NC + -D SX126X_DIO2_AS_RF_SWITCH=1 + -D SX126X_DIO3_TCXO_VOLTAGE=1.8 + -D SX126X_CURRENT_LIMIT=140 + -D SX126X_RX_BOOSTED_GAIN=1 + -D PIN_USER_BTN=0 + -D PIN_WIRE_SCL=7 + -D PIN_WIRE_SDA=6 + -UENV_INCLUDE_GPS +lib_deps = ${nrf52_base.lib_deps} + ${sensor_base.lib_deps} + +[ikoka_stick_nrf_e22_22dbm] +extends = ikoka_stick_nrf +build_flags = + ${ikoka_stick_nrf.build_flags} + -D MANUFACTURER_STRING='"Ikoka Stick-E22-22dBm (Xiao_nrf52)"' + -D LORA_TX_POWER=22 +build_src_filter = ${ikoka_stick_nrf.build_src_filter} + + + + + + + + + +<../variants/ikoka_stick_nrf> + +[ikoka_stick_nrf_e22_30dbm] +extends = ikoka_stick_nrf +build_flags = + ${ikoka_stick_nrf.build_flags} + -D MANUFACTURER_STRING='"Ikoka Stick-E22-30dBm (Xiao_nrf52)"' + -D LORA_TX_POWER=20 +build_src_filter = ${ikoka_stick_nrf.build_src_filter} + + + + + + + + + +<../variants/ikoka_stick_nrf> + +[ikoka_stick_nrf_e22_33dbm] +extends = ikoka_stick_nrf +build_flags = + ${ikoka_stick_nrf.build_flags} + -D MANUFACTURER_STRING='"Ikoka Stick-E22-33dBm (Xiao_nrf52)"' + -D LORA_TX_POWER=9 +build_src_filter = ${ikoka_stick_nrf.build_src_filter} + + + + + + + + + +<../variants/ikoka_stick_nrf> + +[ikoka_stick_nrf_companion_radio_ble] +extends = ikoka_stick_nrf +board_build.ldscript = boards/nrf52840_s140_v7_extrafs.ld +board_upload.maximum_size = 708608 +build_flags = + ${ikoka_stick_nrf.build_flags} + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D BLE_PIN_CODE=123456 + -D OFFLINE_QUEUE_SIZE=256 + -I examples/companion_radio/ui-new + -D QSPIFLASH=1 +build_src_filter = ${ikoka_stick_nrf.build_src_filter} + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${ikoka_stick_nrf.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[ikoka_stick_nrf_companion_radio_usb] +extends = ikoka_stick_nrf +board_build.ldscript = boards/nrf52840_s140_v7_extrafs.ld +board_upload.maximum_size = 708608 +build_flags = + ${ikoka_stick_nrf.build_flags} + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -I examples/companion_radio/ui-new + -D QSPIFLASH=1 + -D ENABLE_USB_INTERFACE +build_src_filter = ${ikoka_stick_nrf.build_src_filter} + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${ikoka_stick_nrf.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[ikoka_stick_nrf_repeater] +extends = ikoka_stick_nrf +build_flags = + ${ikoka_stick_nrf.build_flags} + -D ADVERT_NAME='"Ikoka Stick Repeater"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 +build_src_filter = ${ikoka_stick_nrf.build_src_filter} + + + +<../examples/simple_repeater/*.cpp> + +[ikoka_stick_nrf_room_server] +extends = ikoka_stick_nrf +build_flags = + ${ikoka_stick_nrf.build_flags} + -D ADVERT_NAME='"Ikoka Stick Room"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' +build_src_filter = ${ikoka_stick_nrf.build_src_filter} + +<../examples/simple_room_server/*.cpp> + +[env:ikoka_stick_nrf_22dbm_companion_radio_usb] +extends = + ikoka_stick_nrf_e22_22dbm + ikoka_stick_nrf_companion_radio_usb +build_flags = + ${ikoka_stick_nrf_companion_radio_usb.build_flags} + ${ikoka_stick_nrf_e22_22dbm.build_flags} +build_src_filter = + ${ikoka_stick_nrf_companion_radio_usb.build_src_filter} + ${ikoka_stick_nrf_e22_22dbm.build_src_filter} + +[env:ikoka_stick_nrf_22dbm_companion_radio_ble] +extends = + ikoka_stick_nrf_e22_22dbm + ikoka_stick_nrf_companion_radio_ble +build_flags = + ${ikoka_stick_nrf_companion_radio_ble.build_flags} + ${ikoka_stick_nrf_e22_22dbm.build_flags} +build_src_filter = + ${ikoka_stick_nrf_companion_radio_ble.build_src_filter} + ${ikoka_stick_nrf_e22_22dbm.build_src_filter} + +[env:ikoka_stick_nrf_22dbm_repeater] +extends = + ikoka_stick_nrf_e22_22dbm + ikoka_stick_nrf_repeater +build_flags = + ${ikoka_stick_nrf_repeater.build_flags} + ${ikoka_stick_nrf_e22_22dbm.build_flags} +build_src_filter = + ${ikoka_stick_nrf_repeater.build_src_filter} + ${ikoka_stick_nrf_e22_22dbm.build_src_filter} + +[env:ikoka_stick_nrf_22dbm_room_server] +extends = + ikoka_stick_nrf_e22_22dbm + ikoka_stick_nrf_room_server +build_flags = + ${ikoka_stick_nrf_room_server.build_flags} + ${ikoka_stick_nrf_e22_22dbm.build_flags} +build_src_filter = + ${ikoka_stick_nrf_room_server.build_src_filter} + ${ikoka_stick_nrf_e22_22dbm.build_src_filter} + +[env:ikoka_stick_nrf_30dbm_companion_radio_usb] +extends = + ikoka_stick_nrf_e22_30dbm + ikoka_stick_nrf_companion_radio_usb +build_flags = + ${ikoka_stick_nrf_companion_radio_usb.build_flags} + ${ikoka_stick_nrf_e22_30dbm.build_flags} +build_src_filter = + ${ikoka_stick_nrf_companion_radio_usb.build_src_filter} + ${ikoka_stick_nrf_e22_30dbm.build_src_filter} + +[env:ikoka_stick_nrf_30dbm_companion_radio_ble] +extends = + ikoka_stick_nrf_e22_30dbm + ikoka_stick_nrf_companion_radio_ble +build_flags = + ${ikoka_stick_nrf_companion_radio_ble.build_flags} + ${ikoka_stick_nrf_e22_30dbm.build_flags} +build_src_filter = + ${ikoka_stick_nrf_companion_radio_ble.build_src_filter} + ${ikoka_stick_nrf_e22_30dbm.build_src_filter} + +[env:ikoka_stick_nrf_30dbm_repeater] +extends = + ikoka_stick_nrf_e22_30dbm + ikoka_stick_nrf_repeater +build_flags = + ${ikoka_stick_nrf_repeater.build_flags} + ${ikoka_stick_nrf_e22_30dbm.build_flags} +build_src_filter = + ${ikoka_stick_nrf_repeater.build_src_filter} + ${ikoka_stick_nrf_e22_30dbm.build_src_filter} + +[env:ikoka_stick_nrf_30dbm_room_server] +extends = + ikoka_stick_nrf_e22_30dbm + ikoka_stick_nrf_room_server +build_flags = + ${ikoka_stick_nrf_room_server.build_flags} + ${ikoka_stick_nrf_e22_30dbm.build_flags} +build_src_filter = + ${ikoka_stick_nrf_room_server.build_src_filter} + ${ikoka_stick_nrf_e22_30dbm.build_src_filter} + +[env:ikoka_stick_nrf_33dbm_companion_radio_usb] +extends = + ikoka_stick_nrf_e22_33dbm + ikoka_stick_nrf_companion_radio_usb +build_flags = + ${ikoka_stick_nrf_companion_radio_usb.build_flags} + ${ikoka_stick_nrf_e22_33dbm.build_flags} +build_src_filter = + ${ikoka_stick_nrf_companion_radio_usb.build_src_filter} + ${ikoka_stick_nrf_e22_33dbm.build_src_filter} + +[env:ikoka_stick_nrf_33dbm_companion_radio_ble] +extends = + ikoka_stick_nrf_e22_33dbm + ikoka_stick_nrf_companion_radio_ble +build_flags = + ${ikoka_stick_nrf_companion_radio_ble.build_flags} + ${ikoka_stick_nrf_e22_33dbm.build_flags} +build_src_filter = + ${ikoka_stick_nrf_companion_radio_ble.build_src_filter} + ${ikoka_stick_nrf_e22_33dbm.build_src_filter} + +[env:ikoka_stick_nrf_33dbm_repeater] +extends = + ikoka_stick_nrf_e22_33dbm + ikoka_stick_nrf_repeater +build_flags = + ${ikoka_stick_nrf_repeater.build_flags} + ${ikoka_stick_nrf_e22_33dbm.build_flags} +build_src_filter = + ${ikoka_stick_nrf_repeater.build_src_filter} + ${ikoka_stick_nrf_e22_33dbm.build_src_filter} + +[env:ikoka_stick_nrf_33dbm_room_server] +extends = + ikoka_stick_nrf_e22_33dbm + ikoka_stick_nrf_room_server +build_flags = + ${ikoka_stick_nrf_room_server.build_flags} + ${ikoka_stick_nrf_e22_33dbm.build_flags} +build_src_filter = + ${ikoka_stick_nrf_room_server.build_src_filter} + ${ikoka_stick_nrf_e22_33dbm.build_src_filter} + +[env:ikoka_stick_nrf_22dbm_kiss_modem] +extends = ikoka_stick_nrf_e22_22dbm +build_src_filter = ${ikoka_stick_nrf_e22_22dbm.build_src_filter} + +<../examples/kiss_modem/> + +[env:ikoka_stick_nrf_30dbm_kiss_modem] +extends = ikoka_stick_nrf_e22_30dbm +build_src_filter = ${ikoka_stick_nrf_e22_30dbm.build_src_filter} + +<../examples/kiss_modem/> + +[env:ikoka_stick_nrf_33dbm_kiss_modem] +extends = ikoka_stick_nrf_e22_33dbm +build_src_filter = ${ikoka_stick_nrf_e22_33dbm.build_src_filter} + +<../examples/kiss_modem/> + +[LilyGo_TETH_Elite_sx1262] +extends = esp32_base +board = esp32s3box +board_build.partitions = default_16MB.csv +board_upload.flash_size = 16MB +build_flags = + ${esp32_base.build_flags} + -I variants/lilygo_teth_elite + -D BOARD_HAS_PSRAM + -D LILYGO_TETH_ELITE + -D LILYGO_T_ETH_ELITE_ESP32S3 + -D ARDUINO_USB_CDC_ON_BOOT=1 + -D P_LORA_DIO_1=8 + -D P_LORA_NSS=40 + -D P_LORA_RESET=46 + -D P_LORA_BUSY=16 + -D P_LORA_SCLK=10 + -D P_LORA_MISO=9 + -D P_LORA_MOSI=11 + -D P_LORA_TX_LED=38 + -D SX126X_DIO2_AS_RF_SWITCH=true + -D SX126X_DIO3_TCXO_VOLTAGE=1.8 + -D SX126X_CURRENT_LIMIT=140 + -D USE_SX1262 + -D RADIO_CLASS=CustomSX1262 + -D WRAPPER_CLASS=CustomSX1262Wrapper + -D LORA_TX_POWER=8 + -D SX126X_RX_BOOSTED_GAIN=1 +build_src_filter = ${esp32_base.build_src_filter} + +<../variants/lilygo_teth_elite> +lib_deps = + ${esp32_base.lib_deps} + +[env:LilyGo_TETH_Elite_sx1262_repeater] +extends = LilyGo_TETH_Elite_sx1262 +build_flags = + ${LilyGo_TETH_Elite_sx1262.build_flags} + -D ADVERT_NAME='"T-ETH Elite Repeater"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 +build_src_filter = ${LilyGo_TETH_Elite_sx1262.build_src_filter} + +<../examples/simple_repeater> +lib_deps = + ${LilyGo_TETH_Elite_sx1262.lib_deps} + ${esp32_ota.lib_deps} + +[env:LilyGo_TETH_Elite_sx1262_room_server] +extends = LilyGo_TETH_Elite_sx1262 +build_flags = + ${LilyGo_TETH_Elite_sx1262.build_flags} + -D ADVERT_NAME='"T-ETH Elite Room"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D ROOM_PASSWORD='"hello"' +build_src_filter = ${LilyGo_TETH_Elite_sx1262.build_src_filter} + +<../examples/simple_room_server> +lib_deps = + ${LilyGo_TETH_Elite_sx1262.lib_deps} + ${esp32_ota.lib_deps} + +[env:LilyGo_TETH_Elite_sx1262_companion_radio_usb] +extends = LilyGo_TETH_Elite_sx1262 +build_flags = + ${LilyGo_TETH_Elite_sx1262.build_flags} + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D OFFLINE_QUEUE_SIZE=256 + -D ENABLE_USB_INTERFACE +build_src_filter = ${LilyGo_TETH_Elite_sx1262.build_src_filter} + +<../examples/companion_radio/*.cpp> +lib_deps = + ${LilyGo_TETH_Elite_sx1262.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:LilyGo_TETH_Elite_sx1262_companion_radio_ble] +extends = LilyGo_TETH_Elite_sx1262 +build_flags = + ${LilyGo_TETH_Elite_sx1262.build_flags} + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D BLE_PIN_CODE=123456 + -D BLE_DEBUG_LOGGING=1 + -D OFFLINE_QUEUE_SIZE=256 +build_src_filter = ${LilyGo_TETH_Elite_sx1262.build_src_filter} + + + +<../examples/companion_radio/*.cpp> +lib_deps = + ${LilyGo_TETH_Elite_sx1262.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:LilyGo_TETH_Elite_sx1262_kiss_modem] +extends = LilyGo_TETH_Elite_sx1262 +build_src_filter = ${LilyGo_TETH_Elite_sx1262.build_src_filter} + +<../examples/kiss_modem/> + +[ikoka_handheld_nrf] +extends = nrf52_base +board = seeed-xiao-afruitnrf52-nrf52840 +board_build.ldscript = boards/nrf52840_s140_v7.ld +build_flags = ${nrf52_base.build_flags} + ${sensor_base.build_flags} + -I lib/nrf52/s140_nrf52_7.3.0_API/include + -I lib/nrf52/s140_nrf52_7.3.0_API/include/nrf52 + -I variants/ikoka_handheld_nrf + -UENV_INCLUDE_GPS + -D IKOKA_NRF52 + -D USE_SX1262 + -D RADIO_CLASS=CustomSX1262 + -D WRAPPER_CLASS=CustomSX1262Wrapper + -D P_LORA_TX_LED=11 + -D P_LORA_DIO_1=D1 + -D P_LORA_RESET=D2 + -D P_LORA_BUSY=D3 + -D P_LORA_NSS=D4 + -D SX126X_RXEN=D5 + -D SX126X_TXEN=RADIOLIB_NC + -D SX126X_DIO2_AS_RF_SWITCH=1 + -D SX126X_DIO3_TCXO_VOLTAGE=1.8 + -D SX126X_CURRENT_LIMIT=140 + -D SX126X_RX_BOOSTED_GAIN=1 +build_src_filter = ${nrf52_base.build_src_filter} + +<../variants/ikoka_handheld_nrf> + + +lib_deps = ${nrf52_base.lib_deps} + ${sensor_base.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[ikoka_handheld_nrf_ssd1306_companion] +lib_deps = ${ikoka_handheld_nrf.lib_deps} + adafruit/Adafruit SSD1306 @ ^2.5.13 +build_flags = ${ikoka_handheld_nrf.build_flags} + -D DISPLAY_CLASS=SSD1306Display + -D DISPLAY_ROTATION=0 + -D PIN_WIRE_SCL=D6 + -D PIN_WIRE_SDA=D7 + -D PIN_USER_BTN=D0 + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D OFFLINE_QUEUE_SIZE=256 + -D QSPIFLASH=1 + -I examples/companion_radio/ui-new +build_src_filter = ${ikoka_handheld_nrf.build_src_filter} + + + +<../examples/companion_radio/ui-new/UITask.cpp> + +<../examples/companion_radio/*.cpp> + +[env:ikoka_handheld_nrf_e22_30dbm_096_companion_radio_ble] +extends = ikoka_handheld_nrf +board_build.ldscript = boards/nrf52840_s140_v7_extrafs.ld +build_flags = ${ikoka_handheld_nrf_ssd1306_companion.build_flags} + -D BLE_PIN_CODE=123456 + -D LORA_TX_POWER=20 +build_src_filter = ${ikoka_handheld_nrf_ssd1306_companion.build_src_filter} + + + +[env:ikoka_handheld_nrf_e22_30dbm_096_rotated_companion_radio_ble] +extends = ikoka_handheld_nrf +board_build.ldscript = boards/nrf52840_s140_v7_extrafs.ld +build_flags = ${ikoka_handheld_nrf_ssd1306_companion.build_flags} + -D BLE_PIN_CODE=123456 + -D LORA_TX_POWER=20 + -D DISPLAY_ROTATION=2 +build_src_filter = ${ikoka_handheld_nrf_ssd1306_companion.build_src_filter} + + + +[env:ikoka_handheld_nrf_e22_30dbm_096_companion_radio_usb] +extends = ikoka_handheld_nrf +board_build.ldscript = boards/nrf52840_s140_v7_extrafs.ld +build_flags = ${ikoka_handheld_nrf_ssd1306_companion.build_flags} + -D LORA_TX_POWER=20 + -D ENABLE_USB_INTERFACE +build_src_filter = ${ikoka_handheld_nrf_ssd1306_companion.build_src_filter} + +[env:ikoka_handheld_nrf_e22_30dbm_096_rotated_companion_radio_usb] +extends = ikoka_handheld_nrf +board_build.ldscript = boards/nrf52840_s140_v7_extrafs.ld +build_flags = ${ikoka_handheld_nrf_ssd1306_companion.build_flags} + -D LORA_TX_POWER=20 + -D DISPLAY_ROTATION=2 + -D ENABLE_USB_INTERFACE +build_src_filter = ${ikoka_handheld_nrf_ssd1306_companion.build_src_filter} + +[env:ikoka_handheld_nrf_e22_30dbm_repeater] +extends = ikoka_handheld_nrf +build_flags = ${ikoka_handheld_nrf.build_flags} + -D ADVERT_NAME='"ikoka_handheld Repeater"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 + -D LORA_TX_POWER=20 +build_src_filter = ${ikoka_handheld_nrf.build_src_filter} + +<../examples/simple_repeater/*.cpp> + +[env:ikoka_handheld_nrf_e22_30dbm_room_server] +extends = ikoka_handheld_nrf +build_flags = ${ikoka_handheld_nrf.build_flags} + -D ADVERT_NAME='"ikoka_handheld Room"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D LORA_TX_POWER=20 +build_src_filter = ${ikoka_handheld_nrf.build_src_filter} + +<../examples/simple_room_server/*.cpp> + +[env:ikoka_handheld_nrf_kiss_modem] +extends = ikoka_handheld_nrf +build_flags = ${ikoka_handheld_nrf.build_flags} + -D LORA_TX_POWER=20 +build_src_filter = ${ikoka_handheld_nrf.build_src_filter} + +<../examples/kiss_modem/> + +[Meshadventurer] +extends = esp32_base +board = esp32doit-devkit-v1 +board_build.partitions = min_spiffs.csv +build_flags = + ${esp32_base.build_flags} + -I variants/meshadventurer + -D MESHADVENTURER + -D P_LORA_TX_LED=2 + -D PIN_VBAT_READ=35 + -D PIN_USER_BTN=39 + -D P_LORA_DIO_1=33 + -D P_LORA_NSS=18 + -D P_LORA_RESET=23 + -D P_LORA_BUSY=32 + -D P_LORA_SCLK=5 + -D P_LORA_MOSI=27 + -D P_LORA_MISO=19 + -D SX126X_TXEN=13 + -D SX126X_RXEN=14 + -D PIN_BOARD_SDA=21 + -D PIN_BOARD_SCL=22 + -D SX126X_DIO2_AS_RF_SWITCH=false + -D SX126X_DIO3_TCXO_VOLTAGE=1.8 + -D SX126X_RX_BOOSTED_GAIN=1 + -D PIN_GPS_RX=12 + -D PIN_GPS_TX=15 + -D DISPLAY_CLASS=SSD1306Display +build_src_filter = ${esp32_base.build_src_filter} + +<../variants/meshadventurer> + + + + +lib_deps = + ${esp32_base.lib_deps} + stevemarple/MicroNMEA @ ^2.0.6 + adafruit/Adafruit SSD1306 @ ^2.5.13 + +[env:Meshadventurer_sx1262_repeater] +extends = Meshadventurer +build_src_filter = ${Meshadventurer.build_src_filter} + +<../examples/simple_repeater> +build_flags = + ${Meshadventurer.build_flags} + -D RADIO_CLASS=CustomSX1262 + -D WRAPPER_CLASS=CustomSX1262Wrapper + -D LORA_TX_POWER=22 + -D ADVERT_NAME='"Meshadventurer Repeater"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 +lib_deps = + ${Meshadventurer.lib_deps} + ${esp32_ota.lib_deps} + +[env:Meshadventurer_sx1262_repeater_bridge_espnow] +extends = Meshadventurer +build_src_filter = ${Meshadventurer.build_src_filter} + + + +<../examples/simple_repeater> +build_flags = + ${Meshadventurer.build_flags} + -D RADIO_CLASS=CustomSX1262 + -D WRAPPER_CLASS=CustomSX1262Wrapper + -D LORA_TX_POWER=22 + -D ADVERT_NAME='"ESPNow Bridge"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 + -D WITH_ESPNOW_BRIDGE=1 +lib_deps = + ${Meshadventurer.lib_deps} + ${esp32_ota.lib_deps} + +[env:Meshadventurer_sx1268_repeater] +extends = Meshadventurer +build_src_filter = ${Meshadventurer.build_src_filter} + +<../examples/simple_repeater> +build_flags = + ${Meshadventurer.build_flags} + -D RADIO_CLASS=CustomSX1268 + -D WRAPPER_CLASS=CustomSX1268Wrapper + -D LORA_TX_POWER=22 + -D ADVERT_NAME='"Meshadventurer Repeater"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 +lib_deps = + ${Meshadventurer.lib_deps} + ${esp32_ota.lib_deps} + +[env:Meshadventurer_sx1268_repeater_bridge_espnow] +extends = Meshadventurer +build_src_filter = ${Meshadventurer.build_src_filter} + + + +<../examples/simple_repeater> +build_flags = + ${Meshadventurer.build_flags} + -D RADIO_CLASS=CustomSX1268 + -D WRAPPER_CLASS=CustomSX1268Wrapper + -D LORA_TX_POWER=22 + -D ADVERT_NAME='"ESPNow Bridge"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 + -D WITH_ESPNOW_BRIDGE=1 +lib_deps = + ${Meshadventurer.lib_deps} + ${esp32_ota.lib_deps} + +[env:Meshadventurer_sx1262_companion_radio_usb] +extends = Meshadventurer +build_src_filter = ${Meshadventurer.build_src_filter} + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +build_flags = + ${Meshadventurer.build_flags} + -I examples/companion_radio/ui-new + -D RADIO_CLASS=CustomSX1262 + -D WRAPPER_CLASS=CustomSX1262Wrapper + -D LORA_TX_POWER=22 + -D MAX_CONTACTS=160 + -D MAX_GROUP_CHANNELS=40 + -D OFFLINE_QUEUE_SIZE=128 + -D ENABLE_USB_INTERFACE +lib_deps = + ${Meshadventurer.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:Meshadventurer_sx1262_companion_radio_ble] +extends = Meshadventurer +build_src_filter = ${Meshadventurer.build_src_filter} + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +build_flags = + ${Meshadventurer.build_flags} + -I examples/companion_radio/ui-new + -D RADIO_CLASS=CustomSX1262 + -D WRAPPER_CLASS=CustomSX1262Wrapper + -D LORA_TX_POWER=22 + -D MAX_CONTACTS=160 + -D MAX_GROUP_CHANNELS=40 + -D BLE_PIN_CODE=123456 + -D BLE_DEBUG_LOGGING=1 + -D OFFLINE_QUEUE_SIZE=128 +lib_deps = + ${Meshadventurer.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:Meshadventurer_sx1262_terminal_chat] +extends = Meshadventurer +build_flags = + ${Meshadventurer.build_flags} + -D RADIO_CLASS=CustomSX1262 + -D WRAPPER_CLASS=CustomSX1262Wrapper + -D LORA_TX_POWER=22 + -D MAX_CONTACTS=100 + -D MAX_GROUP_CHANNELS=1 +build_src_filter = ${Meshadventurer.build_src_filter} + +<../examples/simple_secure_chat/main.cpp> +lib_deps = + ${Meshadventurer.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:Meshadventurer_sx1262_room_server] +extends = Meshadventurer +build_flags = + ${Meshadventurer.build_flags} + -D RADIO_CLASS=CustomSX1262 + -D WRAPPER_CLASS=CustomSX1262Wrapper + -D LORA_TX_POWER=22 + -D ADVERT_NAME='"Meshadventurer Room"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D ROOM_PASSWORD='"hello"' +build_src_filter = ${Meshadventurer.build_src_filter} + +<../examples/simple_room_server> +lib_deps = + ${Meshadventurer.lib_deps} + ${esp32_ota.lib_deps} + +[env:Meshadventurer_sx1268_companion_radio_usb] +extends = Meshadventurer +build_src_filter = ${Meshadventurer.build_src_filter} + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +build_flags = + ${Meshadventurer.build_flags} + -I examples/companion_radio/ui-new + -D RADIO_CLASS=CustomSX1268 + -D WRAPPER_CLASS=CustomSX1268Wrapper + -D LORA_TX_POWER=22 + -D MAX_CONTACTS=160 + -D OFFLINE_QUEUE_SIZE=128 + -D MAX_GROUP_CHANNELS=40 + -D ENABLE_USB_INTERFACE +lib_deps = + ${Meshadventurer.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:Meshadventurer_sx1268_companion_radio_ble] +extends = Meshadventurer +build_src_filter = ${Meshadventurer.build_src_filter} + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +build_flags = + ${Meshadventurer.build_flags} + -I examples/companion_radio/ui-new + -D RADIO_CLASS=CustomSX1268 + -D WRAPPER_CLASS=CustomSX1268Wrapper + -D LORA_TX_POWER=22 + -D MAX_CONTACTS=160 + -D MAX_GROUP_CHANNELS=40 + -D BLE_PIN_CODE=123456 + -D BLE_DEBUG_LOGGING=1 + -D OFFLINE_QUEUE_SIZE=128 +lib_deps = + ${Meshadventurer.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:Meshadventurer_sx1268_terminal_chat] +extends = Meshadventurer +build_flags = + ${Meshadventurer.build_flags} + -D RADIO_CLASS=CustomSX1268 + -D WRAPPER_CLASS=CustomSX1268Wrapper + -D LORA_TX_POWER=22 + -D MAX_CONTACTS=100 + -D MAX_GROUP_CHANNELS=1 +build_src_filter = ${Meshadventurer.build_src_filter} + +<../examples/simple_secure_chat/main.cpp> +lib_deps = + ${Meshadventurer.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:Meshadventurer_sx1268_room_server] +extends = Meshadventurer +build_flags = + ${Meshadventurer.build_flags} + -D RADIO_CLASS=CustomSX1268 + -D WRAPPER_CLASS=CustomSX1268Wrapper + -D LORA_TX_POWER=22 + -D ADVERT_NAME='"Meshadventurer Room"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D ROOM_PASSWORD='"hello"' +build_src_filter = ${Meshadventurer.build_src_filter} + +<../examples/simple_room_server> +lib_deps = + ${Meshadventurer.lib_deps} + ${esp32_ota.lib_deps} + +[env:Meshadventurer_sx1262_kiss_modem] +extends = Meshadventurer +build_src_filter = ${Meshadventurer.build_src_filter} + +<../examples/kiss_modem/> +build_flags = ${Meshadventurer.build_flags} + -D RADIO_CLASS=CustomSX1262 + -D WRAPPER_CLASS=CustomSX1262Wrapper + -D LORA_TX_POWER=22 + +[env:Meshadventurer_sx1268_kiss_modem] +extends = Meshadventurer +build_src_filter = ${Meshadventurer.build_src_filter} + +<../examples/kiss_modem/> +build_flags = ${Meshadventurer.build_flags} + -D RADIO_CLASS=CustomSX1268 + -D WRAPPER_CLASS=CustomSX1268Wrapper + -D LORA_TX_POWER=22 + +[LilyGo_T_Impulse_Plus] +extends = nrf52_base +board = lilygo_t_impulse_plus_nrf52840 +board_build.ldscript = boards/nrf52840_s140_v6_extrafs.ld +build_flags = ${nrf52_base.build_flags} + ${sensor_base.build_flags} + -I variants/lilygo_t_impulse_plus + -D USE_SX1262 + -D RADIO_CLASS=CustomSX1262 + -D WRAPPER_CLASS=CustomSX1262Wrapper + -D LORA_TX_POWER=22 + -D SX126X_CURRENT_LIMIT=140 + -D SX126X_RX_BOOSTED_GAIN=1 + -D PIN_USER_BTN=-1 + -D PIN_WIRE_SDA=SCREEN_SDA + -D PIN_WIRE_SCL=SCREEN_SCL + -D ENV_PIN_SDA=IIC_SDA_2 + -D ENV_PIN_SCL=IIC_SCL_2 +build_src_filter = ${nrf52_base.build_src_filter} + + + +<../variants/lilygo_t_impulse_plus> + + + + +lib_deps = ${nrf52_base.lib_deps} + ${sensor_base.lib_deps} + adafruit/Adafruit SSD1306 @ ^2.5.13 + adafruit/Adafruit GFX Library @ ^1.12.1 + +[env:LilyGo_T_Impulse_Plus_repeater] +extends = LilyGo_T_Impulse_Plus +build_src_filter = ${LilyGo_T_Impulse_Plus.build_src_filter} + +<../examples/simple_repeater> +build_flags = + ${LilyGo_T_Impulse_Plus.build_flags} + -D ADVERT_NAME='"T-Impulse-Plus Repeater"' + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 +lib_deps = ${LilyGo_T_Impulse_Plus.lib_deps} + adafruit/RTClib @ ^2.1.3 + +[env:LilyGo_T_Impulse_Plus_companion_radio_ble] +extends = LilyGo_T_Impulse_Plus +build_flags = + ${LilyGo_T_Impulse_Plus.build_flags} + -I src/helpers/ui + -I examples/companion_radio/ui-new + -D DISPLAY_CLASS=SSD1306Display + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D QSPIFLASH=1 + -D BLE_PIN_CODE=123456 + -D OFFLINE_QUEUE_SIZE=256 +build_src_filter = ${LilyGo_T_Impulse_Plus.build_src_filter} + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${LilyGo_T_Impulse_Plus.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:LilyGo_T_Impulse_Plus_kiss_modem] +extends = LilyGo_T_Impulse_Plus +build_src_filter = ${LilyGo_T_Impulse_Plus.build_src_filter} + +<../examples/kiss_modem/> + +[KeepteenLT1] +extends = nrf52_base +board = keepteen_lt1 +build_flags = ${nrf52_base.build_flags} + -I variants/keepteen_lt1 + -D KEEPTEEN_LT1 + -D USE_SX1262 + -D RADIO_CLASS=CustomSX1262 + -D WRAPPER_CLASS=CustomSX1262Wrapper + -D LORA_TX_POWER=22 + -D SX126X_CURRENT_LIMIT=140 + -D SX126X_RX_BOOSTED_GAIN=1 + -D PIN_BOARD_SDA=34 + -D PIN_BOARD_SCL=36 + -D ENV_INCLUDE_GPS=1 +build_src_filter = ${nrf52_base.build_src_filter} + + + +<../variants/keepteen_lt1> +lib_deps = ${nrf52_base.lib_deps} + adafruit/Adafruit SSD1306 @ ^2.5.13 + stevemarple/MicroNMEA @ ^2.0.6 + +[env:KeepteenLT1_repeater] +extends = KeepteenLT1 +build_src_filter = ${KeepteenLT1.build_src_filter} + +<../examples/simple_repeater> + + + + +build_flags = + ${KeepteenLT1.build_flags} + -D ADVERT_NAME='"KeepteenLT1 Repeater"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 + -D DISPLAY_CLASS=SSD1306Display +lib_deps = ${KeepteenLT1.lib_deps} + adafruit/RTClib @ ^2.1.3 + +[env:KeepteenLT1_room_server] +extends = KeepteenLT1 +build_src_filter = ${KeepteenLT1.build_src_filter} + +<../examples/simple_room_server> + + + + +build_flags = ${KeepteenLT1.build_flags} + -D ADVERT_NAME='"KeepteenLT1 Room"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D ROOM_PASSWORD='"hello"' + -D DISPLAY_CLASS=SSD1306Display +lib_deps = ${KeepteenLT1.lib_deps} + adafruit/RTClib @ ^2.1.3 + +[env:KeepteenLT1_companion_radio_usb] +extends = KeepteenLT1 +board_build.ldscript = boards/nrf52840_s140_v6_extrafs.ld +board_upload.maximum_size = 712704 +build_flags = ${KeepteenLT1.build_flags} + -I examples/companion_radio/ui-new + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D DISPLAY_CLASS=SSD1306Display + -D ENABLE_USB_INTERFACE +build_src_filter = ${KeepteenLT1.build_src_filter} + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = ${KeepteenLT1.lib_deps} + adafruit/RTClib @ ^2.1.3 + densaugeo/base64 @ ~1.4.0 + +[env:KeepteenLT1_companion_radio_ble] +extends = KeepteenLT1 +board_build.ldscript = boards/nrf52840_s140_v6_extrafs.ld +board_upload.maximum_size = 712704 +build_flags = ${KeepteenLT1.build_flags} + -I examples/companion_radio/ui-new + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D BLE_PIN_CODE=123456 + -D BLE_DEBUG_LOGGING=1 + -D OFFLINE_QUEUE_SIZE=256 + -D DISPLAY_CLASS=SSD1306Display + -D MESH_DEBUG=1 +build_src_filter = ${KeepteenLT1.build_src_filter} + + + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = ${KeepteenLT1.lib_deps} + adafruit/RTClib @ ^2.1.3 + densaugeo/base64 @ ~1.4.0 + +[env:KeepteenLT1_kiss_modem] +extends = KeepteenLT1 +build_src_filter = ${KeepteenLT1.build_src_filter} + +<../examples/kiss_modem/> + +[Heltec_Wireless_Paper_base] +extends = esp32_base +board = esp32-s3-devkitc-1 +build_flags = + ${esp32_base.build_flags} + -I variants/heltec_wireless_paper + -D HELTEC_WIRELESS_PAPER + -D P_LORA_DIO_1=14 + -D P_LORA_NSS=8 + -D P_LORA_RESET=RADIOLIB_NC + -D P_LORA_BUSY=13 + -D P_LORA_SCLK=9 + -D P_LORA_MISO=11 + -D P_LORA_MOSI=10 + -D USE_SX1262 + -D RADIO_CLASS=CustomSX1262 + -D WRAPPER_CLASS=CustomSX1262Wrapper + -D LORA_TX_POWER=22 + -D P_LORA_TX_LED=18 + -D PIN_USER_BTN=0 + -D PIN_VEXT_EN=45 + -D ADC_MULTIPLIER=8.4 + -D PIN_VBAT_READ=20 + -D PIN_ADC_CTRL=19 + -D SX126X_DIO2_AS_RF_SWITCH=true + -D SX126X_DIO3_TCXO_VOLTAGE=1.8 + -D SX126X_CURRENT_LIMIT=140 + -D SX126X_RX_BOOSTED_GAIN=1 + -D DISP_CS=4 + -D DISP_BUSY=7 + -D DISP_DC=5 + -D DISP_RST=6 + -D DISP_SCLK=3 + -D DISP_MOSI=2 + -D ARDUINO_heltec_wifi_lora_32_V3 + -D WIRELESS_PAPER +build_src_filter = ${esp32_base.build_src_filter} + +<../variants/heltec_wireless_paper> +lib_deps = + ${esp32_base.lib_deps} + https://github.com/todd-herbert/heltec-eink-modules/archive/9207eb6ab2b96f66298e0488740218c17b006af7.zip + +[env:Heltec_Wireless_Paper_companion_radio_ble] +extends = Heltec_Wireless_Paper_base +build_flags = + ${Heltec_Wireless_Paper_base.build_flags} + -I examples/companion_radio/ui-new + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D DISPLAY_CLASS=E213Display + -D BLE_PIN_CODE=123456 + -D OFFLINE_QUEUE_SIZE=256 + -D ENABLE_WIFI_INTERFACE +build_src_filter = ${Heltec_Wireless_Paper_base.build_src_filter} + + + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${Heltec_Wireless_Paper_base.lib_deps} + densaugeo/base64 @ ~1.4.0 + bakercp/CRC32 @ ^2.0.0 + +[env:Heltec_Wireless_Paper_companion_radio_usb] +extends = Heltec_Wireless_Paper_base +build_flags = + ${Heltec_Wireless_Paper_base.build_flags} + -I examples/companion_radio/ui-new + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D DISPLAY_CLASS=E213Display + -D OFFLINE_QUEUE_SIZE=256 + -D ENABLE_USB_INTERFACE +build_src_filter = ${Heltec_Wireless_Paper_base.build_src_filter} + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${Heltec_Wireless_Paper_base.lib_deps} + densaugeo/base64 @ ~1.4.0 + bakercp/CRC32 @ ^2.0.0 + +[env:Heltec_Wireless_Paper_repeater] +extends = Heltec_Wireless_Paper_base +build_flags = + ${Heltec_Wireless_Paper_base.build_flags} + -D DISPLAY_CLASS=E213Display + -D ADVERT_NAME='"Heltec WP Repeater"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 +build_src_filter = ${Heltec_Wireless_Paper_base.build_src_filter} + + + +<../examples/simple_repeater> +lib_deps = + ${Heltec_Wireless_Paper_base.lib_deps} + ${esp32_ota.lib_deps} + bakercp/CRC32 @ ^2.0.0 + +[env:Heltec_Wireless_Paper_repeater_bridge_espnow] +extends = Heltec_Wireless_Paper_base +build_flags = + ${Heltec_Wireless_Paper_base.build_flags} + -D DISPLAY_CLASS=E213Display + -D ADVERT_NAME='"ESPNow Bridge"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 + -D WITH_ESPNOW_BRIDGE=1 +build_src_filter = ${Heltec_Wireless_Paper_base.build_src_filter} + + + + + +<../examples/simple_repeater> +lib_deps = + ${Heltec_Wireless_Paper_base.lib_deps} + ${esp32_ota.lib_deps} + bakercp/CRC32 @ ^2.0.0 + +[env:Heltec_Wireless_Paper_room_server] +extends = Heltec_Wireless_Paper_base +build_flags = + ${Heltec_Wireless_Paper_base.build_flags} + -D DISPLAY_CLASS=E213Display + -D ADVERT_NAME='"Heltec WP Room"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D ROOM_PASSWORD='"hello"' +build_src_filter = ${Heltec_Wireless_Paper_base.build_src_filter} + + + +<../examples/simple_room_server> +lib_deps = + ${Heltec_Wireless_Paper_base.lib_deps} + ${esp32_ota.lib_deps} + bakercp/CRC32 @ ^2.0.0 + +[env:Heltec_Wireless_Paper_kiss_modem] +extends = Heltec_Wireless_Paper_base +build_src_filter = ${Heltec_Wireless_Paper_base.build_src_filter} + +<../examples/kiss_modem/> + +[Heltec_lora32_v4] +extends = esp32_base +board = heltec_v4 +build_flags = + ${esp32_base.build_flags} + ${sensor_base.build_flags} + -I variants/heltec_v4 + -D HELTEC_LORA_V4 + -D USE_SX1262 + -D ESP32_CPU_FREQ=80 + -D RADIO_CLASS=CustomSX1262 + -D WRAPPER_CLASS=CustomSX1262Wrapper + -D P_LORA_TX_LED=35 + -D P_LORA_DIO_1=14 + -D P_LORA_NSS=8 + -D P_LORA_RESET=12 + -D P_LORA_BUSY=13 + -D P_LORA_SCLK=9 + -D P_LORA_MISO=11 + -D P_LORA_MOSI=10 + -D P_LORA_PA_POWER=7 + -D P_LORA_GC1109_PA_EN=2 + -D P_LORA_GC1109_PA_TX_EN=46 + -D P_LORA_KCT8103L_PA_CSD=2 + -D P_LORA_KCT8103L_PA_CTX=5 + -D PIN_USER_BTN=0 + -D PIN_VEXT_EN=36 + -D PIN_VEXT_EN_ACTIVE=HIGH + -D LORA_TX_POWER=10 + -D MAX_LORA_TX_POWER=22 + -D SX126X_REGISTER_PATCH=1 + -D SX126X_DIO2_AS_RF_SWITCH=true + -D SX126X_DIO3_TCXO_VOLTAGE=1.8 + -D SX126X_CURRENT_LIMIT=140 + -D SX126X_RX_BOOSTED_GAIN=1 + -D PIN_GPS_RX=38 + -D PIN_GPS_TX=39 + -D PIN_GPS_RESET=42 + -D PIN_GPS_RESET_ACTIVE=LOW + -D PIN_GPS_EN=34 + -D PIN_GPS_EN_ACTIVE=LOW + -D ENV_INCLUDE_GPS=1 + -D PIN_ADC_CTRL=37 + -D PIN_VBAT_READ=1 +build_src_filter = ${esp32_base.build_src_filter} + +<../variants/heltec_v4> + + +lib_deps = + ${esp32_base.lib_deps} + ${sensor_base.lib_deps} + +[heltec_v4_oled] +extends = Heltec_lora32_v4 +build_flags = + ${Heltec_lora32_v4.build_flags} + -D HELTEC_LORA_V4_OLED + -D PIN_BOARD_SDA=17 + -D PIN_BOARD_SCL=18 + -D PIN_OLED_RESET=21 +build_src_filter = ${Heltec_lora32_v4.build_src_filter} +lib_deps = ${Heltec_lora32_v4.lib_deps} + +[heltec_v4_tft] +extends = Heltec_lora32_v4 +build_flags = + ${Heltec_lora32_v4.build_flags} + -D HELTEC_LORA_V4_TFT + -D PIN_BOARD_SDA=4 + -D PIN_BOARD_SCL=3 + -D DISPLAY_SCALE_X=2.5 + -D DISPLAY_SCALE_Y=3.75 + -D PIN_TFT_RST=18 + -D PIN_TFT_VDD_CTL=-1 + -D PIN_TFT_LEDA_CTL=21 + -D PIN_TFT_LEDA_CTL_ACTIVE=HIGH + -D PIN_TFT_CS=15 + -D PIN_TFT_DC=16 + -D PIN_TFT_SCL=17 + -D PIN_TFT_SDA=33 +build_src_filter = ${Heltec_lora32_v4.build_src_filter} +lib_deps = + ${Heltec_lora32_v4.lib_deps} + adafruit/Adafruit ST7735 and ST7789 Library @ ^1.11.0 + +[env:heltec_v4_repeater] +extends = heltec_v4_oled +build_flags = + ${heltec_v4_oled.build_flags} + -D DISPLAY_CLASS=SSD1306Display + -D ADVERT_NAME='"Heltec Repeater"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 +build_src_filter = ${heltec_v4_oled.build_src_filter} + + + +<../examples/simple_repeater> +lib_deps = + ${heltec_v4_oled.lib_deps} + ${esp32_ota.lib_deps} + bakercp/CRC32 @ ^2.0.0 + +[env:heltec_v4_expansionkit_repeater] +extends = heltec_v4_oled +build_flags = + ${heltec_v4_oled.build_flags} + -D DISPLAY_CLASS=SSD1306Display + -D ADVERT_NAME='"Heltec Repeater"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 + -D ENV_PIN_SDA=4 + -D ENV_PIN_SCL=3 +build_src_filter = ${heltec_v4_oled.build_src_filter} + + + +<../examples/simple_repeater> +lib_deps = + ${heltec_v4_oled.lib_deps} + ${esp32_ota.lib_deps} + bakercp/CRC32 @ ^2.0.0 + +[env:heltec_v4_repeater_bridge_espnow] +extends = heltec_v4_oled +build_flags = + ${heltec_v4_oled.build_flags} + -D DISPLAY_CLASS=SSD1306Display + -D ADVERT_NAME='"ESPNow Bridge"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 + -D WITH_ESPNOW_BRIDGE=1 +build_src_filter = ${heltec_v4_oled.build_src_filter} + + + + + +<../examples/simple_repeater> +lib_deps = + ${heltec_v4_oled.lib_deps} + ${esp32_ota.lib_deps} + +[env:heltec_v4_room_server] +extends = heltec_v4_oled +build_flags = + ${heltec_v4_oled.build_flags} + -D DISPLAY_CLASS=SSD1306Display + -D ADVERT_NAME='"Heltec Room"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D ROOM_PASSWORD='"hello"' +build_src_filter = ${heltec_v4_oled.build_src_filter} + + + +<../examples/simple_room_server> +lib_deps = + ${heltec_v4_oled.lib_deps} + ${esp32_ota.lib_deps} + +[env:heltec_v4_terminal_chat] +extends = heltec_v4_oled +build_flags = + ${heltec_v4_oled.build_flags} + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=1 +build_src_filter = ${heltec_v4_oled.build_src_filter} + +<../examples/simple_secure_chat/main.cpp> +lib_deps = + ${heltec_v4_oled.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:heltec_v4_companion_radio_usb] +extends = heltec_v4_oled +build_flags = + ${heltec_v4_oled.build_flags} + -I examples/companion_radio/ui-new + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D DISPLAY_CLASS=SSD1306Display + -D ENABLE_USB_INTERFACE +build_src_filter = ${heltec_v4_oled.build_src_filter} + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${heltec_v4_oled.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:heltec_v4_companion_radio_ble] +extends = heltec_v4_oled +build_flags = + ${heltec_v4_oled.build_flags} + -I examples/companion_radio/ui-new + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D DISPLAY_CLASS=SSD1306Display + -D BLE_PIN_CODE=123456 + -D AUTO_SHUTDOWN_MILLIVOLTS=3400 + -D BLE_DEBUG_LOGGING=1 + -D OFFLINE_QUEUE_SIZE=256 + -D ENABLE_WIFI_INTERFACE +build_src_filter = ${heltec_v4_oled.build_src_filter} + + + + + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${heltec_v4_oled.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:heltec_v4_companion_radio_wifi] +extends = heltec_v4_oled +build_flags = + ${heltec_v4_oled.build_flags} + -I examples/companion_radio/ui-new + -D ENABLE_WIFI_INTERFACE + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D OFFLINE_QUEUE_SIZE=256 + -D DISPLAY_CLASS=SSD1306Display + -D WIFI_DEBUG_LOGGING=1 + -D WIFI_SSID='"myssid"' + -D WIFI_PWD='"mypwd"' +build_src_filter = ${heltec_v4_oled.build_src_filter} + + + + + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${heltec_v4_oled.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:heltec_v4_sensor] +extends = heltec_v4_oled +build_flags = + ${heltec_v4_oled.build_flags} + -D ADVERT_NAME='"Heltec v4 Sensor"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D ENV_PIN_SDA=3 + -D ENV_PIN_SCL=4 + -D DISPLAY_CLASS=SSD1306Display +build_src_filter = ${heltec_v4_oled.build_src_filter} + + + +<../examples/simple_sensor> +lib_deps = + ${heltec_v4_oled.lib_deps} + ${esp32_ota.lib_deps} + +[env:heltec_v4_tft_repeater] +extends = heltec_v4_tft +build_flags = + ${heltec_v4_tft.build_flags} + -D DISPLAY_CLASS=ST7789LCDDisplay + -D ADVERT_NAME='"Heltec Repeater"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 +build_src_filter = ${heltec_v4_tft.build_src_filter} + + + +<../examples/simple_repeater> +lib_deps = + ${heltec_v4_tft.lib_deps} + ${esp32_ota.lib_deps} + bakercp/CRC32 @ ^2.0.0 + +[env:heltec_v4_tft_repeater_bridge_espnow] +extends = heltec_v4_tft +build_flags = + ${heltec_v4_tft.build_flags} + -D DISPLAY_CLASS=ST7789LCDDisplay + -D ADVERT_NAME='"ESPNow Bridge"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 + -D WITH_ESPNOW_BRIDGE=1 +build_src_filter = ${heltec_v4_tft.build_src_filter} + + + + + +<../examples/simple_repeater> +lib_deps = + ${heltec_v4_tft.lib_deps} + ${esp32_ota.lib_deps} + +[env:heltec_v4_tft_room_server] +extends = heltec_v4_tft +build_flags = + ${heltec_v4_tft.build_flags} + -D DISPLAY_CLASS=ST7789LCDDisplay + -D ADVERT_NAME='"Heltec Room"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D ROOM_PASSWORD='"hello"' +build_src_filter = ${heltec_v4_tft.build_src_filter} + + + +<../examples/simple_room_server> +lib_deps = + ${heltec_v4_tft.lib_deps} + ${esp32_ota.lib_deps} + +[env:heltec_v4_tft_terminal_chat] +extends = heltec_v4_tft +build_flags = + ${heltec_v4_tft.build_flags} + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=1 +build_src_filter = ${heltec_v4_tft.build_src_filter} + +<../examples/simple_secure_chat/main.cpp> +lib_deps = + ${heltec_v4_tft.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:heltec_v4_tft_companion_radio_usb] +extends = heltec_v4_tft +build_flags = + ${heltec_v4_tft.build_flags} + -I examples/companion_radio/ui-new + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D DISPLAY_CLASS=ST7789LCDDisplay + -D ENABLE_USB_INTERFACE +build_src_filter = ${heltec_v4_tft.build_src_filter} + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${heltec_v4_tft.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:heltec_v4_tft_companion_radio_ble] +extends = heltec_v4_tft +build_flags = + ${heltec_v4_tft.build_flags} + -I examples/companion_radio/ui-new + -D DISPLAY_CLASS=ST7789LCDDisplay + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D BLE_PIN_CODE=123456 + -D AUTO_SHUTDOWN_MILLIVOLTS=3400 + -D BLE_DEBUG_LOGGING=1 + -D OFFLINE_QUEUE_SIZE=256 + -D ENABLE_WIFI_INTERFACE +build_src_filter = ${heltec_v4_tft.build_src_filter} + + + + + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${heltec_v4_tft.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:heltec_v4_tft_companion_radio_wifi] +extends = heltec_v4_tft +build_flags = + ${heltec_v4_tft.build_flags} + -I examples/companion_radio/ui-new + -D ENABLE_WIFI_INTERFACE + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D OFFLINE_QUEUE_SIZE=256 + -D DISPLAY_CLASS=ST7789LCDDisplay + -D WIFI_DEBUG_LOGGING=1 + -D WIFI_SSID='"myssid"' + -D WIFI_PWD='"mypwd"' +build_src_filter = ${heltec_v4_tft.build_src_filter} + + + + + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${heltec_v4_tft.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:heltec_v4_tft_sensor] +extends = heltec_v4_tft +build_flags = + ${heltec_v4_tft.build_flags} + -D ADVERT_NAME='"Heltec v4 Sensor"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D ENV_PIN_SDA=3 + -D ENV_PIN_SCL=4 + -D DISPLAY_CLASS=ST7789LCDDisplay +build_src_filter = ${heltec_v4_tft.build_src_filter} + + + +<../examples/simple_sensor> +lib_deps = + ${heltec_v4_tft.lib_deps} + ${esp32_ota.lib_deps} + +[env:heltec_v4_kiss_modem] +extends = Heltec_lora32_v4 +build_unflags = + -DARDUINO_USB_MODE=0 +build_flags = + ${Heltec_lora32_v4.build_flags} + -DARDUINO_USB_MODE=1 +build_src_filter = ${Heltec_lora32_v4.build_src_filter} + +<../examples/kiss_modem/> + +[Heltec_tracker_v2] +extends = esp32_base +board = heltec_tracker_v2 +build_flags = + ${esp32_base.build_flags} + ${sensor_base.build_flags} + -I variants/heltec_tracker_v2 + -D HELTEC_TRACKER_V2 + -D ESP32_CPU_FREQ=160 + -D USE_SX1262 + -D RADIO_CLASS=CustomSX1262 + -D WRAPPER_CLASS=CustomSX1262Wrapper + -D P_LORA_TX_LED=18 + -D P_LORA_DIO_1=14 + -D P_LORA_NSS=8 + -D P_LORA_RESET=12 + -D P_LORA_BUSY=13 + -D P_LORA_SCLK=9 + -D P_LORA_MISO=11 + -D P_LORA_MOSI=10 + -D P_LORA_PA_POWER=7 + -D P_LORA_KCT8103L_PA_CSD=4 + -D P_LORA_KCT8103L_PA_CTX=5 + -D LORA_TX_POWER=9 + -D MAX_LORA_TX_POWER=22 + -D SX126X_DIO2_AS_RF_SWITCH=true + -D SX126X_DIO3_TCXO_VOLTAGE=1.8 + -D SX126X_CURRENT_LIMIT=140 + -D SX126X_RX_BOOSTED_GAIN=1 + -D SX126X_REGISTER_PATCH=1 + -D PIN_BOARD_SDA=6 + -D PIN_BOARD_SCL=17 + -D PIN_USER_BTN=0 + -D PIN_TFT_SDA=42 + -D PIN_TFT_SCL=41 + -D PIN_TFT_DC=40 + -D PIN_TFT_RST=39 + -D PIN_TFT_CS=38 + -D USE_PIN_TFT=1 + -D PIN_VEXT_EN=3 + -D PIN_VEXT_EN_ACTIVE=HIGH + -D PIN_TFT_LEDA_CTL=21 + -D DISPLAY_ROTATION=1 + -D PIN_GPS_RX=34 + -D PIN_GPS_TX=33 + -D PIN_GPS_RESET=35 + -D PIN_GPS_RESET_ACTIVE=LOW + -D GPS_BAUD_RATE=115200 + -D ENV_INCLUDE_GPS=1 + -D PIN_ADC_CTRL=2 + -D PIN_VBAT_READ=1 +build_src_filter = ${esp32_base.build_src_filter} + +<../variants/heltec_tracker_v2> + + +lib_deps = + ${esp32_base.lib_deps} + ${sensor_base.lib_deps} + bodmer/TFT_eSPI @ ^2.4.31 + +[env:heltec_tracker_v2_repeater] +extends = Heltec_tracker_v2 +build_flags = + ${Heltec_tracker_v2.build_flags} + -D DISPLAY_CLASS=ST7735Display + -D ADVERT_NAME='"Heltec Repeater"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 +build_src_filter = ${Heltec_tracker_v2.build_src_filter} + + + +<../examples/simple_repeater> +lib_deps = + ${Heltec_tracker_v2.lib_deps} + ${esp32_ota.lib_deps} + bakercp/CRC32 @ ^2.0.0 + +[env:heltec_tracker_v2_repeater_bridge_espnow] +extends = Heltec_tracker_v2 +build_flags = + ${Heltec_tracker_v2.build_flags} + -D DISPLAY_CLASS=ST7735Display + -D ADVERT_NAME='"ESPNow Bridge"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 + -D WITH_ESPNOW_BRIDGE=1 +build_src_filter = ${Heltec_tracker_v2.build_src_filter} + + + + + +<../examples/simple_repeater> +lib_deps = + ${Heltec_tracker_v2.lib_deps} + ${esp32_ota.lib_deps} + +[env:heltec_tracker_v2_room_server] +extends = Heltec_tracker_v2 +build_flags = + ${Heltec_tracker_v2.build_flags} + -D DISPLAY_CLASS=ST7735Display + -D ADVERT_NAME='"Heltec Room"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D ROOM_PASSWORD='"hello"' +build_src_filter = ${Heltec_tracker_v2.build_src_filter} + + + +<../examples/simple_room_server> +lib_deps = + ${Heltec_tracker_v2.lib_deps} + ${esp32_ota.lib_deps} + +[env:heltec_tracker_v2_terminal_chat] +extends = Heltec_tracker_v2 +build_flags = + ${Heltec_tracker_v2.build_flags} + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=1 +build_src_filter = ${Heltec_tracker_v2.build_src_filter} + +<../examples/simple_secure_chat/main.cpp> +lib_deps = + ${Heltec_tracker_v2.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:heltec_tracker_v2_companion_radio_usb] +extends = Heltec_tracker_v2 +build_flags = + ${Heltec_tracker_v2.build_flags} + -I examples/companion_radio/ui-new + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D DISPLAY_CLASS=ST7735Display + -D ENABLE_USB_INTERFACE +build_src_filter = ${Heltec_tracker_v2.build_src_filter} + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${Heltec_tracker_v2.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:heltec_tracker_v2_companion_radio_ble] +extends = Heltec_tracker_v2 +build_flags = + ${Heltec_tracker_v2.build_flags} + -I examples/companion_radio/ui-new + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D DISPLAY_CLASS=ST7735Display + -D BLE_PIN_CODE=123456 + -D AUTO_SHUTDOWN_MILLIVOLTS=3400 + -D BLE_DEBUG_LOGGING=1 + -D OFFLINE_QUEUE_SIZE=256 +build_src_filter = ${Heltec_tracker_v2.build_src_filter} + + + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${Heltec_tracker_v2.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:heltec_tracker_v2_companion_radio_wifi] +extends = Heltec_tracker_v2 +build_flags = + ${Heltec_tracker_v2.build_flags} + -I examples/companion_radio/ui-new + -D ENABLE_WIFI_INTERFACE + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D DISPLAY_CLASS=ST7735Display + -D WIFI_DEBUG_LOGGING=1 + -D WIFI_SSID='"myssid"' + -D WIFI_PWD='"mypwd"' + -D OFFLINE_QUEUE_SIZE=256 +build_src_filter = ${Heltec_tracker_v2.build_src_filter} + + + + + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${Heltec_tracker_v2.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:heltec_tracker_v2_sensor] +extends = Heltec_tracker_v2 +build_flags = + ${Heltec_tracker_v2.build_flags} + -D ADVERT_NAME='"Heltec Tracker V2 Sensor"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D DISPLAY_CLASS=ST7735Display +build_src_filter = ${Heltec_tracker_v2.build_src_filter} + + + +<../examples/simple_sensor> +lib_deps = + ${Heltec_tracker_v2.lib_deps} + ${esp32_ota.lib_deps} + +[env:heltec_tracker_v2_kiss_modem] +extends = Heltec_tracker_v2 +build_src_filter = ${Heltec_tracker_v2.build_src_filter} + +<../examples/kiss_modem/> + +[LilyGo_T-Echo] +extends = nrf52_base +board = t-echo +board_build.ldscript = boards/nrf52840_s140_v6.ld +build_flags = ${nrf52_base.build_flags} + -I variants/lilygo_techo + -I src/helpers/nrf52 + -I lib/nrf52/s140_nrf52_6.1.1_API/include + -I lib/nrf52/s140_nrf52_6.1.1_API/include/nrf52 + -D LILYGO_TECHO + -D RADIO_CLASS=CustomSX1262 + -D WRAPPER_CLASS=CustomSX1262Wrapper + -D LORA_TX_POWER=22 + -D P_LORA_DIO_1=20 + -D P_LORA_NSS=24 + -D P_LORA_RESET=25 + -D P_LORA_BUSY=17 + -D P_LORA_SCLK=19 + -D P_LORA_MISO=23 + -D P_LORA_MOSI=22 + -D SX126X_POWER_EN=37 + -D SX126X_DIO2_AS_RF_SWITCH=true + -D SX126X_DIO3_TCXO_VOLTAGE=1.8 + -D SX126X_CURRENT_LIMIT=140 + -D SX126X_RX_BOOSTED_GAIN=1 + -D P_LORA_TX_LED=LED_GREEN + -D DISABLE_DIAGNOSTIC_OUTPUT + -D ENV_INCLUDE_GPS=1 + -D ENV_INCLUDE_BME280=1 + -D GPS_BAUD_RATE=9600 + -D PIN_GPS_EN=GPS_EN + -D PIN_GPS_RESET_ACTIVE=LOW + -D TELEM_BME280_ADDRESS=0x77 + -D DISPLAY_CLASS=GxEPDDisplay + -D EINK_DISPLAY_MODEL=GxEPD2_154_D67 + -D EINK_SCALE_X=1.5625f + -D EINK_SCALE_Y=1.5625f + -D EINK_X_OFFSET=0 + -D EINK_Y_OFFSET=10 + -D EINK_SCREENOFF_BLANK + -D UI_RECENT_LIST_SIZE=9 + -D UI_MSG_PREVIEW_SIZE=165 + -D EINK_MAX_PARTIAL_REFRESH=60 + -D AUTO_OFF_MILLIS=900000 + -D BACKLIGHT_BTN=PIN_BUTTON2 +build_src_filter = ${nrf52_base.build_src_filter} + + + + + + + + + + + +<../variants/lilygo_techo> +lib_deps = + ${nrf52_base.lib_deps} + stevemarple/MicroNMEA @ ^2.0.6 + adafruit/Adafruit BME280 Library @ ^2.3.0 + zinggjm/GxEPD2 @ 1.6.2 + bakercp/CRC32 @ ^2.0.0 +debug_tool = jlink +upload_protocol = nrfutil + +[env:LilyGo_T-Echo_repeater] +extends = LilyGo_T-Echo +build_src_filter = ${LilyGo_T-Echo.build_src_filter} + +<../examples/simple_repeater> +build_flags = + ${LilyGo_T-Echo.build_flags} + -D ADVERT_NAME='"T-Echo Repeater"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 + +[env:LilyGo_T-Echo_room_server] +extends = LilyGo_T-Echo +build_src_filter = ${LilyGo_T-Echo.build_src_filter} + +<../examples/simple_room_server> +build_flags = + ${LilyGo_T-Echo.build_flags} + -D ADVERT_NAME='"T-Echo Room"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + +[env:LilyGo_T-Echo_companion_radio_ble] +extends = LilyGo_T-Echo +board_build.ldscript = boards/nrf52840_s140_v6_extrafs.ld +board_upload.maximum_size = 712704 +build_flags = + ${LilyGo_T-Echo.build_flags} + -I src/helpers/ui + -I examples/companion_radio/ui-new + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D QSPIFLASH=1 + -D BLE_PIN_CODE=123456 + -D OFFLINE_QUEUE_SIZE=256 + -D UI_SENSORS_PAGE=1 + -D UI_GPS_PAGE=1 + -D AUTO_SHUTDOWN_MILLIVOLTS=3300 +build_src_filter = ${LilyGo_T-Echo.build_src_filter} + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${LilyGo_T-Echo.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:LilyGo_T-Echo_companion_radio_usb] +extends = LilyGo_T-Echo +board_build.ldscript = boards/nrf52840_s140_v6_extrafs.ld +board_upload.maximum_size = 712704 +build_flags = + ${LilyGo_T-Echo.build_flags} + -I src/helpers/ui + -I examples/companion_radio/ui-new + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D OFFLINE_QUEUE_SIZE=256 + -D UI_SENSORS_PAGE=1 + -D AUTO_SHUTDOWN_MILLIVOLTS=3300 + -D QSPIFLASH=1 + -D ENABLE_USB_INTERFACE +build_src_filter = ${LilyGo_T-Echo.build_src_filter} + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${LilyGo_T-Echo.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:LilyGo_T-Echo_kiss_modem] +extends = LilyGo_T-Echo +build_src_filter = ${LilyGo_T-Echo.build_src_filter} + +<../examples/kiss_modem/> + +[Heltec_lora32_v3] +extends = esp32_base +board = esp32-s3-devkitc-1 +build_flags = + ${esp32_base.build_flags} + ${sensor_base.build_flags} + -I variants/heltec_v3 + -D HELTEC_LORA_V3 + -D ESP32_CPU_FREQ=80 + -D P_LORA_DIO_1=14 + -D P_LORA_NSS=8 + -D P_LORA_RESET=RADIOLIB_NC + -D P_LORA_BUSY=13 + -D P_LORA_SCLK=9 + -D P_LORA_MISO=11 + -D P_LORA_MOSI=10 + -D USE_SX1262 + -D RADIO_CLASS=CustomSX1262 + -D WRAPPER_CLASS=CustomSX1262Wrapper + -D LORA_TX_POWER=22 + -D P_LORA_TX_LED=35 + -D PIN_BOARD_SDA=17 + -D PIN_BOARD_SCL=18 + -D PIN_USER_BTN=0 + -D PIN_VEXT_EN=36 + -D SX126X_DIO2_AS_RF_SWITCH=true + -D SX126X_DIO3_TCXO_VOLTAGE=1.8 + -D SX126X_CURRENT_LIMIT=140 + -D SX126X_RX_BOOSTED_GAIN=1 + -D PIN_GPS_RX=47 + -D PIN_GPS_TX=48 + -D PIN_GPS_EN=26 +build_src_filter = ${esp32_base.build_src_filter} + +<../variants/heltec_v3> + + +lib_deps = + ${esp32_base.lib_deps} + ${sensor_base.lib_deps} + +[env:Heltec_v3_repeater] +extends = Heltec_lora32_v3 +build_flags = + ${Heltec_lora32_v3.build_flags} + -D DISPLAY_CLASS=SSD1306Display + -D ADVERT_NAME='"Heltec Repeater"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 +build_src_filter = ${Heltec_lora32_v3.build_src_filter} + + + +<../examples/simple_repeater> +lib_deps = + ${Heltec_lora32_v3.lib_deps} + ${esp32_ota.lib_deps} + bakercp/CRC32 @ ^2.0.0 + +[env:Heltec_v3_repeater_bridge_rs232] +extends = Heltec_lora32_v3 +build_flags = + ${Heltec_lora32_v3.build_flags} + -D DISPLAY_CLASS=SSD1306Display + -D ADVERT_NAME='"RS232 Bridge"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 + -D WITH_RS232_BRIDGE=Serial2 + -D WITH_RS232_BRIDGE_RX=5 + -D WITH_RS232_BRIDGE_TX=6 +build_src_filter = ${Heltec_lora32_v3.build_src_filter} + + + + + +<../examples/simple_repeater> +lib_deps = + ${Heltec_lora32_v3.lib_deps} + ${esp32_ota.lib_deps} + +[env:Heltec_v3_repeater_bridge_espnow] +extends = Heltec_lora32_v3 +build_flags = + ${Heltec_lora32_v3.build_flags} + -D DISPLAY_CLASS=SSD1306Display + -D ADVERT_NAME='"ESPNow Bridge"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 + -D WITH_ESPNOW_BRIDGE=1 +build_src_filter = ${Heltec_lora32_v3.build_src_filter} + + + + + +<../examples/simple_repeater> +lib_deps = + ${Heltec_lora32_v3.lib_deps} + ${esp32_ota.lib_deps} + +[env:Heltec_v3_room_server] +extends = Heltec_lora32_v3 +build_flags = + ${Heltec_lora32_v3.build_flags} + -D DISPLAY_CLASS=SSD1306Display + -D ADVERT_NAME='"Heltec Room"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D ROOM_PASSWORD='"hello"' +build_src_filter = ${Heltec_lora32_v3.build_src_filter} + + + +<../examples/simple_room_server> +lib_deps = + ${Heltec_lora32_v3.lib_deps} + ${esp32_ota.lib_deps} + +[env:Heltec_v3_terminal_chat] +extends = Heltec_lora32_v3 +build_flags = + ${Heltec_lora32_v3.build_flags} + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=1 +build_src_filter = ${Heltec_lora32_v3.build_src_filter} + +<../examples/simple_secure_chat/main.cpp> +lib_deps = + ${Heltec_lora32_v3.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:Heltec_v3_companion_radio_usb] +extends = Heltec_lora32_v3 +build_flags = + ${Heltec_lora32_v3.build_flags} + -I examples/companion_radio/ui-new + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D DISPLAY_CLASS=SSD1306Display + -D ENABLE_USB_INTERFACE +build_src_filter = ${Heltec_lora32_v3.build_src_filter} + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${Heltec_lora32_v3.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:Heltec_v3_companion_radio_ble] +extends = Heltec_lora32_v3 +build_flags = + ${Heltec_lora32_v3.build_flags} + -I examples/companion_radio/ui-new + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D DISPLAY_CLASS=SSD1306Display + -D BLE_PIN_CODE=123456 + -D AUTO_SHUTDOWN_MILLIVOLTS=3400 + -D BLE_DEBUG_LOGGING=1 + -D OFFLINE_QUEUE_SIZE=256 + -D ENABLE_WIFI_INTERFACE +build_src_filter = ${Heltec_lora32_v3.build_src_filter} + + + + + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${Heltec_lora32_v3.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:Heltec_v3_companion_radio_wifi] +extends = Heltec_lora32_v3 +build_flags = + ${Heltec_lora32_v3.build_flags} + -I examples/companion_radio/ui-new + -D ENABLE_WIFI_INTERFACE + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D DISPLAY_CLASS=SSD1306Display + -D WIFI_DEBUG_LOGGING=1 + -D WIFI_SSID='"myssid"' + -D WIFI_PWD='"mypwd"' + -D OFFLINE_QUEUE_SIZE=256 +build_src_filter = ${Heltec_lora32_v3.build_src_filter} + + + + + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${Heltec_lora32_v3.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:Heltec_v3_sensor] +extends = Heltec_lora32_v3 +build_flags = + ${Heltec_lora32_v3.build_flags} + -D ADVERT_NAME='"Heltec v3 Sensor"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D ENV_PIN_SDA=33 + -D ENV_PIN_SCL=34 + -D DISPLAY_CLASS=SSD1306Display +build_src_filter = ${Heltec_lora32_v3.build_src_filter} + + + +<../examples/simple_sensor> +lib_deps = + ${Heltec_lora32_v3.lib_deps} + ${esp32_ota.lib_deps} + +[env:Heltec_WSL3_repeater] +extends = Heltec_lora32_v3 +build_flags = + ${Heltec_lora32_v3.build_flags} + -D ADVERT_NAME='"Heltec Repeater"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 +build_src_filter = ${Heltec_lora32_v3.build_src_filter} + +<../examples/simple_repeater> +lib_deps = + ${Heltec_lora32_v3.lib_deps} + ${esp32_ota.lib_deps} + bakercp/CRC32 @ ^2.0.0 + +[env:Heltec_WSL3_repeater_bridge_rs232] +extends = Heltec_lora32_v3 +build_flags = + ${Heltec_lora32_v3.build_flags} + -D ADVERT_NAME='"RS232 Bridge"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 + -D WITH_RS232_BRIDGE=Serial2 + -D WITH_RS232_BRIDGE_RX=5 + -D WITH_RS232_BRIDGE_TX=6 +build_src_filter = ${Heltec_lora32_v3.build_src_filter} + + + +<../examples/simple_repeater> +lib_deps = + ${Heltec_lora32_v3.lib_deps} + ${esp32_ota.lib_deps} + bakercp/CRC32 @ ^2.0.0 + +[env:Heltec_WSL3_repeater_bridge_espnow] +extends = Heltec_lora32_v3 +build_flags = + ${Heltec_lora32_v3.build_flags} + -D ADVERT_NAME='"ESPNow Bridge"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 + -D WITH_ESPNOW_BRIDGE=1 +build_src_filter = ${Heltec_lora32_v3.build_src_filter} + + + +<../examples/simple_repeater> +lib_deps = + ${Heltec_lora32_v3.lib_deps} + ${esp32_ota.lib_deps} + bakercp/CRC32 @ ^2.0.0 + +[env:Heltec_WSL3_room_server] +extends = Heltec_lora32_v3 +build_src_filter = ${Heltec_lora32_v3.build_src_filter} + +<../examples/simple_room_server> +build_flags = + ${Heltec_lora32_v3.build_flags} + -D ADVERT_NAME='"Heltec Room"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D ROOM_PASSWORD='"hello"' +lib_deps = + ${Heltec_lora32_v3.lib_deps} + ${esp32_ota.lib_deps} + +[env:Heltec_WSL3_companion_radio_ble] +extends = Heltec_lora32_v3 +build_flags = + ${Heltec_lora32_v3.build_flags} + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D BLE_PIN_CODE=123456 + -D OFFLINE_QUEUE_SIZE=256 + -D ENABLE_WIFI_INTERFACE +build_src_filter = ${Heltec_lora32_v3.build_src_filter} + + + + + +<../examples/companion_radio/*.cpp> +lib_deps = + ${Heltec_lora32_v3.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:Heltec_WSL3_companion_radio_usb] +extends = Heltec_lora32_v3 +build_flags = + ${Heltec_lora32_v3.build_flags} + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D ENABLE_USB_INTERFACE +build_src_filter = ${Heltec_lora32_v3.build_src_filter} + +<../examples/companion_radio/*.cpp> +lib_deps = + ${Heltec_lora32_v3.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:Heltec_WSL3_companion_radio_wifi] +extends = Heltec_lora32_v3 +build_flags = + ${Heltec_lora32_v3.build_flags} + -D ENABLE_WIFI_INTERFACE + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D WIFI_DEBUG_LOGGING=1 + -D WIFI_SSID='"myssid"' + -D WIFI_PWD='"mypwd"' + -D OFFLINE_QUEUE_SIZE=256 +build_src_filter = ${Heltec_lora32_v3.build_src_filter} + + + + + +<../examples/companion_radio/*.cpp> +lib_deps = + ${Heltec_lora32_v3.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:Heltec_WSL3_sensor] +extends = Heltec_lora32_v3 +build_flags = + ${Heltec_lora32_v3.build_flags} + -D ADVERT_NAME='"Heltec Sensor"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' +build_src_filter = ${Heltec_lora32_v3.build_src_filter} + +<../examples/simple_sensor> +lib_deps = + ${Heltec_lora32_v3.lib_deps} + ${esp32_ota.lib_deps} + +[env:Heltec_v3_kiss_modem] +extends = Heltec_lora32_v3 +build_src_filter = ${Heltec_lora32_v3.build_src_filter} + +<../examples/kiss_modem/> + +[LilyGo_T3S3_sx1276] +extends = esp32_base +board = t3_s3_v1_x +build_flags = + ${esp32_base.build_flags} + -I variants/lilygo_t3s3_sx1276 + -D LILYGO_T3S3 + -D P_LORA_DIO_0=9 + -D P_LORA_DIO_1=33 + -D P_LORA_NSS=7 + -D P_LORA_RESET=8 + -D P_LORA_SCLK=5 + -D P_LORA_MISO=3 + -D P_LORA_MOSI=6 + -D P_LORA_TX_LED=37 + -D PIN_VBAT_READ=1 + -D PIN_USER_BTN=0 + -D PIN_BOARD_SDA=18 + -D PIN_BOARD_SCL=17 + -D PIN_OLED_RESET=21 + -D RADIO_CLASS=CustomSX1276 + -D WRAPPER_CLASS=CustomSX1276Wrapper + -D SX127X_CURRENT_LIMIT=120 + -D SX127X_RXEN=21 + -D SX127X_TXEN=10 + -D LORA_TX_POWER=20 +build_src_filter = ${esp32_base.build_src_filter} + +<../variants/lilygo_t3s3_sx1276> +lib_deps = + ${esp32_base.lib_deps} + adafruit/Adafruit SSD1306 @ ^2.5.13 + +[env:LilyGo_T3S3_sx1276_repeater] +extends = LilyGo_T3S3_sx1276 +build_flags = + ${LilyGo_T3S3_sx1276.build_flags} + -D DISPLAY_CLASS=SSD1306Display + -D ADVERT_NAME='"T3S3-1276 Repeater"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 +build_src_filter = ${LilyGo_T3S3_sx1276.build_src_filter} + + + +<../examples/simple_repeater> +lib_deps = + ${LilyGo_T3S3_sx1276.lib_deps} + ${esp32_ota.lib_deps} + +[env:LilyGo_T3S3_sx1276_repeater_bridge_espnow] +extends = LilyGo_T3S3_sx1276 +build_flags = + ${LilyGo_T3S3_sx1276.build_flags} + -D DISPLAY_CLASS=SSD1306Display + -D ADVERT_NAME='"ESPNow Bridge"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 + -D WITH_ESPNOW_BRIDGE=1 +build_src_filter = ${LilyGo_T3S3_sx1276.build_src_filter} + + + + + +<../examples/simple_repeater> +lib_deps = + ${LilyGo_T3S3_sx1276.lib_deps} + ${esp32_ota.lib_deps} + +[env:LilyGo_T3S3_sx1276_terminal_chat] +extends = LilyGo_T3S3_sx1276 +build_flags = + ${LilyGo_T3S3_sx1276.build_flags} + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=1 +build_src_filter = ${LilyGo_T3S3_sx1276.build_src_filter} + +<../examples/simple_secure_chat/main.cpp> +lib_deps = + ${LilyGo_T3S3_sx1276.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:LilyGo_T3S3_sx1276_room_server] +extends = LilyGo_T3S3_sx1276 +build_flags = + ${LilyGo_T3S3_sx1276.build_flags} + -D DISPLAY_CLASS=SSD1306Display + -D ADVERT_NAME='"T3S3-1276 Room"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D ROOM_PASSWORD='"hello"' +build_src_filter = ${LilyGo_T3S3_sx1276.build_src_filter} + + + +<../examples/simple_room_server> +lib_deps = + ${LilyGo_T3S3_sx1276.lib_deps} + ${esp32_ota.lib_deps} + +[env:LilyGo_T3S3_sx1276_companion_radio_usb] +extends = LilyGo_T3S3_sx1276 +upload_speed = 115200 +build_flags = + ${LilyGo_T3S3_sx1276.build_flags} + -I examples/companion_radio/ui-new + -D DISPLAY_CLASS=SSD1306Display + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D ENABLE_USB_INTERFACE +build_src_filter = ${LilyGo_T3S3_sx1276.build_src_filter} + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${LilyGo_T3S3_sx1276.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:LilyGo_T3S3_sx1276_companion_radio_ble] +extends = LilyGo_T3S3_sx1276 +build_flags = + ${LilyGo_T3S3_sx1276.build_flags} + -I examples/companion_radio/ui-new + -D DISPLAY_CLASS=SSD1306Display + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D BLE_PIN_CODE=123456 + -D BLE_DEBUG_LOGGING=1 + -D OFFLINE_QUEUE_SIZE=256 +build_src_filter = ${LilyGo_T3S3_sx1276.build_src_filter} + + + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${LilyGo_T3S3_sx1276.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:LilyGo_T3S3_sx1276_kiss_modem] +extends = LilyGo_T3S3_sx1276 +build_src_filter = ${LilyGo_T3S3_sx1276.build_src_filter} + +<../examples/kiss_modem/> + +[LilyGo_T-Echo_Card] +extends = nrf52_base +board = t-echo +board_build.ldscript = boards/nrf52840_s140_v6.ld +build_flags = ${nrf52_base.build_flags} + -I variants/lilygo_techo_card + -I src/helpers/nrf52 + -I lib/nrf52/s140_nrf52_6.1.1_API/include + -I lib/nrf52/s140_nrf52_6.1.1_API/include/nrf52 + -D LILYGO_TECHO_CARD + -D RADIO_CLASS=CustomSX1262 + -D WRAPPER_CLASS=CustomSX1262Wrapper + -D LORA_TX_POWER=22 + -D SX126X_CURRENT_LIMIT=140 + -D SX126X_RX_BOOSTED_GAIN=1 + -D HAS_NEOPIXEL=1 + -D HAS_TORCH=1 + -D DISABLE_DIAGNOSTIC_OUTPUT + -D ENV_INCLUDE_GPS=1 + -D DISPLAY_CLASS=U8g2Display + -D PIN_OLED_RESET=-1 +build_src_filter = ${nrf52_base.build_src_filter} + + + + + + + + + + + +<../variants/lilygo_techo_card> +lib_deps = + ${nrf52_base.lib_deps} + stevemarple/MicroNMEA @ ^2.0.6 + olikraus/U8g2 @ ^2.35.19 + adafruit/Adafruit NeoPixel@^1.10.0 + bakercp/CRC32 @ ^2.0.0 +debug_tool = jlink +upload_protocol = nrfutil + +[env:LilyGo_T-Echo_Card_repeater] +extends = LilyGo_T-Echo_Card +build_src_filter = ${LilyGo_T-Echo_Card.build_src_filter} + +<../examples/simple_repeater> +build_flags = + ${LilyGo_T-Echo_Card.build_flags} + -D ADVERT_NAME='"T-Echo Card Repeater"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 + +[env:LilyGo_T-Echo_Card_room_server] +extends = LilyGo_T-Echo_Card +build_src_filter = ${LilyGo_T-Echo_Card.build_src_filter} + +<../examples/simple_room_server> +build_flags = + ${LilyGo_T-Echo_Card.build_flags} + -D ADVERT_NAME='"T-Echo Card Room"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + +[env:LilyGo_T-Echo_Card_companion_radio_ble] +extends = LilyGo_T-Echo_Card +board_build.ldscript = boards/nrf52840_s140_v6_extrafs.ld +board_upload.maximum_size = 712704 +build_flags = + ${LilyGo_T-Echo_Card.build_flags} + -I src/helpers/ui + -I examples/companion_radio/ui-tiny + -D PIN_BUZZER=38 + -D QSPIFLASH=1 + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D BLE_PIN_CODE=123456 + -D OFFLINE_QUEUE_SIZE=256 + -D UI_RECENT_LIST_SIZE=3 + -D UI_GPS_PAGE=1 + -D AUTO_SHUTDOWN_MILLIVOLTS=3300 +build_src_filter = ${LilyGo_T-Echo_Card.build_src_filter} + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-tiny/*.cpp> + + +lib_deps = + ${LilyGo_T-Echo_Card.lib_deps} + end2endzone/NonBlockingRTTTL@^1.3.0 + densaugeo/base64 @ ~1.4.0 + +[env:LilyGo_T-Echo_Card_companion_radio_usb] +extends = LilyGo_T-Echo_Card +board_build.ldscript = boards/nrf52840_s140_v6_extrafs.ld +board_upload.maximum_size = 712704 +build_flags = + ${LilyGo_T-Echo_Card.build_flags} + -I src/helpers/ui + -I examples/companion_radio/ui-tiny + -D PIN_BUZZER=38 + -D QSPIFLASH=1 + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D OFFLINE_QUEUE_SIZE=256 + -D UI_RECENT_LIST_SIZE=3 + -D UI_GPS_PAGE=1 + -D AUTO_SHUTDOWN_MILLIVOLTS=3300 + -D ENABLE_USB_INTERFACE +build_src_filter = ${LilyGo_T-Echo_Card.build_src_filter} + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-tiny/*.cpp> + + +lib_deps = + ${LilyGo_T-Echo_Card.lib_deps} + end2endzone/NonBlockingRTTTL@^1.3.0 + densaugeo/base64 @ ~1.4.0 + +[env:LilyGo_T-Echo_Card_kiss_modem] +extends = LilyGo_T-Echo_Card +build_src_filter = ${LilyGo_T-Echo_Card.build_src_filter} + +<../examples/kiss_modem/> + +[tlora_c6] +extends = esp32c6_base +board = esp32-c6-devkitm-1 +board_build.partitions = min_spiffs.csv +build_flags = + ${esp32c6_base.build_flags} + -I variants/lilygo_tlora_c6 + -D ARDUINO_USB_CDC_ON_BOOT=1 + -D ARDUINO_USB_MODE=1 + -D P_LORA_TX_LED=7 + -D P_LORA_SCLK=6 + -D P_LORA_MISO=1 + -D P_LORA_MOSI=0 + -D P_LORA_NSS=18 + -D P_LORA_DIO_1=23 + -D P_LORA_BUSY=22 + -D P_LORA_RESET=21 + -D PIN_BOARD_SDA=8 + -D PIN_BOARD_SCL=9 + -D SX126X_RXEN=15 + -D SX126X_TXEN=14 + -D SX126X_DIO2_AS_RF_SWITCH=true + -D SX126X_DIO3_TCXO_VOLTAGE=1.8 + -D SX126X_CURRENT_LIMIT=140 + -D SX126X_RX_BOOSTED_GAIN=1 + -D USE_SX1262 + -D RADIO_CLASS=CustomSX1262 + -D WRAPPER_CLASS=CustomSX1262Wrapper + -D LORA_TX_POWER=22 + -D DISABLE_WIFI_OTA=1 +build_src_filter = ${esp32c6_base.build_src_filter} + +<../variants/lilygo_tlora_c6> + +[env:LilyGo_Tlora_C6_repeater_] +extends = tlora_c6 +build_src_filter = ${tlora_c6.build_src_filter} + +<../examples/simple_repeater/*.cpp> +build_flags = + ${tlora_c6.build_flags} + -D ADVERT_NAME='"Tlora C6 Repeater"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 +lib_deps = + ${tlora_c6.lib_deps} + ${esp32_ota.lib_deps} + +[env:LilyGo_Tlora_C6_room_server_] +extends = tlora_c6 +build_src_filter = ${tlora_c6.build_src_filter} + +<../examples/simple_room_server> +build_flags = + ${tlora_c6.build_flags} + -D ADVERT_NAME='"Tlora C6 Room"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D ROOM_PASSWORD='"hello"' +lib_deps = + ${tlora_c6.lib_deps} + ${esp32_ota.lib_deps} + +[env:LilyGo_Tlora_C6_companion_radio_ble_] +extends = tlora_c6 +build_flags = ${tlora_c6.build_flags} + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D BLE_PIN_CODE=123456 + -D BLE_DEBUG_LOGGING=1 + -D OFFLINE_QUEUE_SIZE=256 + -D ENABLE_PRIVATE_KEY_IMPORT=1 + -D ENABLE_PRIVATE_KEY_EXPORT=1 +build_src_filter = ${tlora_c6.build_src_filter} + + + - + +<../examples/companion_radio/*.cpp> +lib_deps = + ${tlora_c6.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:LilyGo_Tlora_C6_kiss_modem] +extends = tlora_c6 +build_src_filter = ${tlora_c6.build_src_filter} + +<../examples/kiss_modem/> + +[Generic_ESPNOW] +extends = esp32_base +board = esp32-c3-devkitm-1 +build_flags = + ${esp32_base.build_flags} + -I variants/generic_espnow + -D PIN_BOARD_SDA=-1 + -D PIN_BOARD_SCL=-1 + -D PIN_USER_BTN=0 +build_src_filter = ${esp32_base.build_src_filter} + + + +<../variants/generic_espnow> + +[env:Generic_ESPNOW_terminal_chat] +extends = Generic_ESPNOW +build_flags = + ${Generic_ESPNOW.build_flags} + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=1 +build_src_filter = ${Generic_ESPNOW.build_src_filter} + +<../examples/simple_secure_chat/main.cpp> +lib_deps = + ${Generic_ESPNOW.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:Generic_ESPNOW_repeatr] +extends = Generic_ESPNOW +build_flags = + ${Generic_ESPNOW.build_flags} + -D ADVERT_NAME='"ESPNOW Repeater"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 +build_src_filter = ${Generic_ESPNOW.build_src_filter} + +<../examples/simple_repeater/*.cpp> +lib_deps = + ${Generic_ESPNOW.lib_deps} + ${esp32_ota.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:Generic_ESPNOW_comp_radio_usb] +extends = Generic_ESPNOW +build_flags = + ${Generic_ESPNOW.build_flags} + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=8 +build_src_filter = ${Generic_ESPNOW.build_src_filter} + +<../examples/companion_radio/*.cpp> +lib_deps = + ${Generic_ESPNOW.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:Generic_ESPNOW_room_svr] +extends = Generic_ESPNOW +build_flags = + ${Generic_ESPNOW.build_flags} + -D ADVERT_NAME='"Generic ESPNow Room"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D ROOM_PASSWORD='"hello"' +build_src_filter = ${Generic_ESPNOW.build_src_filter} + +<../examples/simple_room_server/*.cpp> +lib_deps = + ${Generic_ESPNOW.lib_deps} + ${esp32_ota.lib_deps} + +[Waveshare_S3_LR1121] +extends = esp32_base +board = esp32-s3-zero +board_build.partitions = min_spiffs.csv +build_flags = ${esp32_base.build_flags} + -I variants/waveshare_esp32s3_lr1121 + -D BOARD_HAS_PSRAM + -D P_LORA_DIO_1=38 + -D P_LORA_NSS=42 + -D P_LORA_RESET=39 + -D P_LORA_BUSY=41 + -D P_LORA_SCLK=40 + -D P_LORA_MISO=46 + -D P_LORA_MOSI=45 + -D RADIO_CLASS=CustomLR1121 + -D WRAPPER_CLASS=CustomLR1121Wrapper + -D LR11X0_DIO3_TCXO_VOLTAGE=1.8 + -D LR1121_FORCE_HP_PA + -D RX_BOOSTED_GAIN=true + -D LORA_TX_POWER=22 +build_src_filter = ${esp32_base.build_src_filter} + +<../variants/waveshare_esp32s3_lr1121> +lib_deps = + ${esp32_base.lib_deps} + +[env:Waveshare_S3_LR1121_repeater] +extends = Waveshare_S3_LR1121 +build_flags = + ${Waveshare_S3_LR1121.build_flags} + -D ADVERT_NAME='"Waveshare LR1121 Repeater"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 +build_src_filter = ${Waveshare_S3_LR1121.build_src_filter} + +<../examples/simple_repeater/*.cpp> +lib_deps = + ${Waveshare_S3_LR1121.lib_deps} + ${esp32_ota.lib_deps} + +[env:Waveshare_S3_LR1121_room_server] +extends = Waveshare_S3_LR1121 +build_flags = + ${Waveshare_S3_LR1121.build_flags} + -D ADVERT_NAME='"Waveshare LR1121 Room"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D ROOM_PASSWORD='"hello"' +build_src_filter = ${Waveshare_S3_LR1121.build_src_filter} + +<../examples/simple_room_server> +lib_deps = + ${Waveshare_S3_LR1121.lib_deps} + ${esp32_ota.lib_deps} + +[env:Waveshare_S3_LR1121_companion_radio_usb] +extends = Waveshare_S3_LR1121 +build_flags = + ${Waveshare_S3_LR1121.build_flags} + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D OFFLINE_QUEUE_SIZE=256 + -D ENABLE_USB_INTERFACE +build_src_filter = ${Waveshare_S3_LR1121.build_src_filter} + + + +<../examples/companion_radio/*.cpp> +lib_deps = + ${Waveshare_S3_LR1121.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:Waveshare_S3_LR1121_companion_radio_ble] +extends = Waveshare_S3_LR1121 +build_flags = + ${Waveshare_S3_LR1121.build_flags} + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D OFFLINE_QUEUE_SIZE=256 + -D BLE_PIN_CODE=123456 +build_src_filter = ${Waveshare_S3_LR1121.build_src_filter} + + + +<../examples/companion_radio/*.cpp> +lib_deps = + ${Waveshare_S3_LR1121.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:Waveshare_S3_LR1121_kiss_modem] +extends = Waveshare_S3_LR1121 +build_src_filter = ${Waveshare_S3_LR1121.build_src_filter} + +<../examples/kiss_modem/> + +[Xiao_C6] +extends = esp32c6_base +board = esp32-c6-devkitm-1 +board_build.flash_mode = dio +board_build.partitions = min_spiffs.csv +build_flags = + ${esp32c6_base.build_flags} + -I variants/xiao_c6 + -D ARDUINO_USB_CDC_ON_BOOT=1 + -D ARDUINO_USB_MODE=1 + -D P_LORA_TX_LED=15 + -D P_LORA_SCLK=19 + -D P_LORA_MISO=20 + -D P_LORA_MOSI=18 + -D P_LORA_NSS=22 + -D P_LORA_DIO_1=1 + -D P_LORA_BUSY=21 + -D P_LORA_RESET=2 + -D PIN_BOARD_SDA=16 + -D PIN_BOARD_SCL=17 + -D SX126X_RXEN=23 + -D SX126X_DIO2_AS_RF_SWITCH=true + -D SX126X_DIO3_TCXO_VOLTAGE=1.8 + -D SX126X_CURRENT_LIMIT=140 + -D SX126X_RX_BOOSTED_GAIN=1 + -D USE_SX1262 + -D RADIO_CLASS=CustomSX1262 + -D WRAPPER_CLASS=CustomSX1262Wrapper + -D LORA_TX_POWER=22 + -D DISABLE_WIFI_OTA=1 +build_src_filter = ${esp32c6_base.build_src_filter} + +<../variants/xiao_c6> + + + +[env:Xiao_C6_repeater_] +extends = Xiao_C6 +build_src_filter = ${Xiao_C6.build_src_filter} + +<../examples/simple_repeater/*.cpp> +build_flags = + ${Xiao_C6.build_flags} + -D ADVERT_NAME='"Xiao C6 Repeater"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 +lib_deps = + ${Xiao_C6.lib_deps} + ${esp32_ota.lib_deps} + +[env:Xiao_C6_companion_radio_ble_] +extends = Xiao_C6 +build_flags = ${Xiao_C6.build_flags} + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D BLE_PIN_CODE=123456 + -D BLE_DEBUG_LOGGING=1 + -D OFFLINE_QUEUE_SIZE=256 + -D ENABLE_PRIVATE_KEY_IMPORT=1 + -D ENABLE_PRIVATE_KEY_EXPORT=1 +build_src_filter = ${Xiao_C6.build_src_filter} + + + - + +<../examples/companion_radio/*.cpp> +lib_deps = + ${Xiao_C6.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[Meshimi] +extends = Xiao_C6 +board_build.partitions = max_app_4MB.csv +build_flags = + ${Xiao_C6.build_flags} + -D P_LORA_TX_LED=15 + -D P_LORA_SCLK=19 + -D P_LORA_MISO=20 + -D P_LORA_MOSI=18 + -D P_LORA_NSS=21 + -D P_LORA_DIO_1=7 + -D P_LORA_BUSY=6 + -D P_LORA_RESET=2 + -D PIN_BOARD_SDA=22 + -D PIN_BOARD_SCL=23 + -D SX126X_RXEN=4 + -D SX126X_DIO2_AS_RF_SWITCH=true + -D SX126X_DIO3_TCXO_VOLTAGE=1.8 + -D SX126X_CURRENT_LIMIT=140 + -D SX126X_RX_BOOSTED_GAIN=1 + -D USE_XIAO_ESP32C6_EXTERNAL_ANTENNA=1 + +[env:Meshimi_repeater_] +extends = Meshimi +build_src_filter = ${Meshimi.build_src_filter} + +<../examples/simple_repeater/*.cpp> +build_flags = + ${Meshimi.build_flags} + -D ADVERT_NAME='"Meshimi Repeater"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 +lib_deps = + ${Meshimi.lib_deps} + +[env:Meshimi_companion_radio_ble_] +extends = Meshimi +build_flags = ${Meshimi.build_flags} + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D BLE_PIN_CODE=123456 + -D BLE_DEBUG_LOGGING=1 + -D OFFLINE_QUEUE_SIZE=256 + -D ENABLE_PRIVATE_KEY_IMPORT=1 + -D ENABLE_PRIVATE_KEY_EXPORT=1 +build_src_filter = ${Meshimi.build_src_filter} + + + - + +<../examples/companion_radio/*.cpp> +lib_deps = + ${Meshimi.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[WHY2025_badge] +extends = Xiao_C6 +board_build.partitions = default_8MB.csv +board_upload.flash_size = 8MB +board_upload.maximum_size = 8388608 +build_flags = + ${Xiao_C6.build_flags} + -D P_LORA_SCLK=6 + -D P_LORA_MISO=2 + -D P_LORA_MOSI=7 + -D P_LORA_NSS=4 + -D P_LORA_DIO_1=5 + -D P_LORA_BUSY=11 + -D P_LORA_RESET=1 + -D SX126X_TXEN=3 + -UPIN_BOARD_SDA + -UPIN_BOARD_SCL + -UP_LORA_TX_LED + -USX126X_RXEN + -USX126X_DIO2_AS_RF_SWITCH + -USX126X_DIO3_TCXO_VOLTAGE + +[env:WHY2025_badge_repeater_] +extends = WHY2025_badge +build_src_filter = ${WHY2025_badge.build_src_filter} + +<../examples/simple_repeater/*.cpp> +build_flags = + ${WHY2025_badge.build_flags} + -D ADVERT_NAME='"WHY2025 Badge Repeater"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 +lib_deps = + ${WHY2025_badge.lib_deps} + ${esp32_ota.lib_deps} + +[env:WHY2025_badge_companion_radio_ble_] +extends = WHY2025_badge +build_flags = ${WHY2025_badge.build_flags} + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D BLE_PIN_CODE=123456 + -D BLE_DEBUG_LOGGING=1 + -D OFFLINE_QUEUE_SIZE=256 + -D ENABLE_PRIVATE_KEY_IMPORT=1 + -D ENABLE_PRIVATE_KEY_EXPORT=1 +build_src_filter = ${WHY2025_badge.build_src_filter} + + + - + +<../examples/companion_radio/*.cpp> +lib_deps = + ${WHY2025_badge.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:Xiao_C6_kiss_modem] +extends = Xiao_C6 +build_src_filter = ${Xiao_C6.build_src_filter} + +<../examples/kiss_modem/> + +[Heltec_t114] +extends = nrf52_base +board = heltec_t114 +board_build.ldscript = boards/nrf52840_s140_v6.ld +build_flags = ${nrf52_base.build_flags} + ${sensor_base.build_flags} + -I lib/nrf52/s140_nrf52_6.1.1_API/include + -I lib/nrf52/s140_nrf52_6.1.1_API/include/nrf52 + -I variants/heltec_t114 + -I src/helpers/ui + -D HELTEC_T114 + -D P_LORA_DIO_1=20 + -D P_LORA_NSS=24 + -D P_LORA_RESET=25 + -D P_LORA_BUSY=17 + -D P_LORA_SCLK=19 + -D P_LORA_MISO=23 + -D P_LORA_MOSI=22 + -D P_LORA_TX_LED=35 + -D RADIO_CLASS=CustomSX1262 + -D WRAPPER_CLASS=CustomSX1262Wrapper + -D LORA_TX_POWER=22 + -D SX126X_POWER_EN=37 + -D SX126X_DIO2_AS_RF_SWITCH=true + -D SX126X_DIO3_TCXO_VOLTAGE=1.8 + -D SX126X_CURRENT_LIMIT=140 + -D SX126X_RX_BOOSTED_GAIN=1 + -D PIN_GPS_RX=39 + -D PIN_GPS_TX=37 + -D PIN_GPS_EN=21 + -D PIN_GPS_RESET=38 + -D PIN_GPS_RESET_ACTIVE=LOW + -D ENV_PIN_SDA=PIN_WIRE1_SDA + -D ENV_PIN_SCL=PIN_WIRE1_SCL +build_src_filter = ${nrf52_base.build_src_filter} + + + + + +<../variants/heltec_t114> +lib_deps = + ${nrf52_base.lib_deps} + ${sensor_base.lib_deps} +debug_tool = jlink +upload_protocol = nrfutil + +[env:Heltec_t114_without_display_repeater] +extends = Heltec_t114 +build_src_filter = ${Heltec_t114.build_src_filter} + +<../examples/simple_repeater> +build_flags = + ${Heltec_t114.build_flags} + -D ADVERT_NAME='"Heltec_T114 Repeater"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 + +[env:Heltec_t114_without_display_repeater_bridge_rs232] +extends = Heltec_t114 +build_flags = + ${Heltec_t114.build_flags} + -D ADVERT_NAME='"RS232 Bridge"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 + -D WITH_RS232_BRIDGE=Serial2 + -D WITH_RS232_BRIDGE_RX=9 + -D WITH_RS232_BRIDGE_TX=10 +build_src_filter = ${Heltec_t114.build_src_filter} + + + +<../examples/simple_repeater> + +[env:Heltec_t114_without_display_room_server] +extends = Heltec_t114 +build_src_filter = ${Heltec_t114.build_src_filter} + +<../examples/simple_room_server> +build_flags = + ${Heltec_t114.build_flags} + -D ADVERT_NAME='"Heltec_T114 Room"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D ROOM_PASSWORD='"hello"' + +[env:Heltec_t114_without_display_companion_radio_ble] +extends = Heltec_t114 +board_build.ldscript = boards/nrf52840_s140_v6_extrafs.ld +board_upload.maximum_size = 712704 +build_flags = + ${Heltec_t114.build_flags} + -I examples/companion_radio/ui-new + -D DISPLAY_CLASS=NullDisplayDriver + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D BLE_PIN_CODE=123456 + -D OFFLINE_QUEUE_SIZE=256 +build_src_filter = ${Heltec_t114.build_src_filter} + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${Heltec_t114.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:Heltec_t114_without_display_companion_radio_usb] +extends = Heltec_t114 +board_build.ldscript = boards/nrf52840_s140_v6_extrafs.ld +board_upload.maximum_size = 712704 +build_flags = + ${Heltec_t114.build_flags} + -I examples/companion_radio/ui-new + -D DISPLAY_CLASS=NullDisplayDriver + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D ENABLE_USB_INTERFACE +build_src_filter = ${Heltec_t114.build_src_filter} + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${Heltec_t114.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[Heltec_t114_with_display] +extends = Heltec_t114 +board = heltec_t114 +board_build.ldscript = boards/nrf52840_s140_v6.ld +build_flags = ${Heltec_t114.build_flags} + -D ST7789 + -D HELTEC_T114_WITH_DISPLAY + -D DISPLAY_CLASS=ST7789Display +build_src_filter = ${Heltec_t114.build_src_filter} + + + + + + + + +lib_deps = + ${Heltec_t114.lib_deps} + adafruit/Adafruit SSD1306 @ ^2.5.13 +debug_tool = jlink +upload_protocol = nrfutil + +[env:Heltec_t114_repeater] +extends = Heltec_t114_with_display +build_src_filter = ${Heltec_t114_with_display.build_src_filter} + +<../examples/simple_repeater> +build_flags = + ${Heltec_t114_with_display.build_flags} + -D ADVERT_NAME='"Heltec_T114 Repeater"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 + +[env:Heltec_t114_repeater_bridge_rs232] +extends = Heltec_t114 +build_flags = + ${Heltec_t114.build_flags} + -D ADVERT_NAME='"RS232 Bridge"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 + -D WITH_RS232_BRIDGE=Serial2 + -D WITH_RS232_BRIDGE_RX=9 + -D WITH_RS232_BRIDGE_TX=10 +build_src_filter = ${Heltec_t114_with_display.build_src_filter} + + + +<../examples/simple_repeater> + +[env:Heltec_t114_room_server] +extends = Heltec_t114_with_display +build_src_filter = ${Heltec_t114_with_display.build_src_filter} + +<../examples/simple_room_server> +build_flags = + ${Heltec_t114_with_display.build_flags} + -D ADVERT_NAME='"Heltec_T114 Room"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D ROOM_PASSWORD='"hello"' + +[env:Heltec_t114_companion_radio_ble] +extends = Heltec_t114_with_display +board_build.ldscript = boards/nrf52840_s140_v6_extrafs.ld +board_upload.maximum_size = 712704 +build_flags = + ${Heltec_t114_with_display.build_flags} + -I examples/companion_radio/ui-new + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D BLE_PIN_CODE=123456 + -D ENV_INCLUDE_GPS=1 + -D OFFLINE_QUEUE_SIZE=256 +build_src_filter = ${Heltec_t114_with_display.build_src_filter} + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${Heltec_t114_with_display.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:Heltec_t114_companion_radio_usb] +extends = Heltec_t114_with_display +board_build.ldscript = boards/nrf52840_s140_v6_extrafs.ld +board_upload.maximum_size = 712704 +build_flags = + ${Heltec_t114_with_display.build_flags} + -I examples/companion_radio/ui-new + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D ENABLE_USB_INTERFACE +build_src_filter = ${Heltec_t114_with_display.build_src_filter} + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${Heltec_t114_with_display.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:Heltec_t114_kiss_modem] +extends = Heltec_t114 +build_src_filter = ${Heltec_t114.build_src_filter} + +<../examples/kiss_modem/> + +[Heltec_lora32_v2] +extends = esp32_base +board = heltec_wifi_lora_32_V2 +build_flags = + ${esp32_base.build_flags} + -I variants/heltec_v2 + -D HELTEC_LORA_V2 + -D RADIO_CLASS=CustomSX1276 + -D WRAPPER_CLASS=CustomSX1276Wrapper + -D P_LORA_DIO_0=26 + -D P_LORA_DIO_1=35 + -D P_LORA_NSS=18 + -D P_LORA_RESET=14 + -D P_LORA_SCLK=5 + -D P_LORA_MISO=19 + -D P_LORA_MOSI=27 + -D P_LORA_TX_LED=25 + -D SX127X_CURRENT_LIMIT=120 + -D LORA_TX_POWER=20 + -D PIN_BOARD_SDA=4 + -D PIN_BOARD_SCL=15 + -D PIN_USER_BTN=0 + -D PIN_OLED_RESET=16 +build_src_filter = ${esp32_base.build_src_filter} + +<../variants/heltec_v2> +lib_deps = + ${esp32_base.lib_deps} + adafruit/Adafruit SSD1306 @ ^2.5.13 + +[env:Heltec_v2_repeater] +extends = Heltec_lora32_v2 +build_flags = + ${Heltec_lora32_v2.build_flags} + -D DISPLAY_CLASS=SSD1306Display + -D ADVERT_NAME='"Heltec Repeater"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 +build_src_filter = ${Heltec_lora32_v2.build_src_filter} + +<../examples/simple_repeater> + + + + +lib_deps = + ${Heltec_lora32_v2.lib_deps} + ${esp32_ota.lib_deps} + +[env:Heltec_v2_repeater_bridge_espnow] +extends = Heltec_lora32_v2 +build_flags = + ${Heltec_lora32_v2.build_flags} + -D DISPLAY_CLASS=SSD1306Display + -D ADVERT_NAME='"ESPNow Bridge"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 + -D WITH_ESPNOW_BRIDGE=1 +build_src_filter = ${Heltec_lora32_v2.build_src_filter} + + + + + + + +<../examples/simple_repeater> +lib_deps = + ${Heltec_lora32_v2.lib_deps} + ${esp32_ota.lib_deps} + +[env:Heltec_v2_room_server] +extends = Heltec_lora32_v2 +build_flags = + ${Heltec_lora32_v2.build_flags} + -D DISPLAY_CLASS=SSD1306Display + -D ADVERT_NAME='"Heltec Room"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D ROOM_PASSWORD='"hello"' +build_src_filter = ${Heltec_lora32_v2.build_src_filter} + + + + + +<../examples/simple_room_server> +lib_deps = + ${Heltec_lora32_v2.lib_deps} + ${esp32_ota.lib_deps} + +[env:Heltec_v2_terminal_chat] +extends = Heltec_lora32_v2 +build_flags = + ${Heltec_lora32_v2.build_flags} + -D MAX_CONTACTS=160 + -D MAX_GROUP_CHANNELS=1 +build_src_filter = ${Heltec_lora32_v2.build_src_filter} + +<../examples/simple_secure_chat/main.cpp> +lib_deps = + ${Heltec_lora32_v2.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:Heltec_v2_companion_radio_usb] +extends = Heltec_lora32_v2 +build_flags = + ${Heltec_lora32_v2.build_flags} + -I examples/companion_radio/ui-new + -D DISPLAY_CLASS=SSD1306Display + -D MAX_CONTACTS=160 + -D MAX_GROUP_CHANNELS=8 + -D ENABLE_USB_INTERFACE +build_src_filter = ${Heltec_lora32_v2.build_src_filter} + + + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${Heltec_lora32_v2.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:Heltec_v2_companion_radio_ble] +extends = Heltec_lora32_v2 +build_flags = + ${Heltec_lora32_v2.build_flags} + -I examples/companion_radio/ui-new + -D DISPLAY_CLASS=SSD1306Display + -D MAX_CONTACTS=160 + -D MAX_GROUP_CHANNELS=8 + -D BLE_PIN_CODE=123456 + -D BLE_DEBUG_LOGGING=1 + -D OFFLINE_QUEUE_SIZE=128 +build_src_filter = ${Heltec_lora32_v2.build_src_filter} + + + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${Heltec_lora32_v2.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:Heltec_v2_companion_radio_wifi] +extends = Heltec_lora32_v2 +build_flags = + ${Heltec_lora32_v2.build_flags} + -I examples/companion_radio/ui-new + -D ENABLE_WIFI_INTERFACE + -D DISPLAY_CLASS=SSD1306Display + -D MAX_CONTACTS=160 + -D MAX_GROUP_CHANNELS=8 + -D WIFI_DEBUG_LOGGING=1 + -D WIFI_SSID='"myssid"' + -D WIFI_PWD='"mypwd"' + -D OFFLINE_QUEUE_SIZE=128 +build_src_filter = ${Heltec_lora32_v2.build_src_filter} + + + + + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${Heltec_lora32_v2.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:Heltec_v2_kiss_modem] +extends = Heltec_lora32_v2 +build_src_filter = ${Heltec_lora32_v2.build_src_filter} + +<../examples/kiss_modem/> + +[nibble_screen_connect_base] +extends = esp32_base +board = esp32-s3-zero +build_flags = + ${esp32_base.build_flags} + -I variants/nibble_screen_connect + -D NIBBLE_SCREEN_CONNECT + -D P_LORA_DIO_1=4 + -D P_LORA_NSS=10 + -D P_LORA_RESET=6 + -D P_LORA_BUSY=5 + -D P_LORA_SCLK=13 + -D P_LORA_MISO=12 + -D P_LORA_MOSI=11 + -D PIN_USER_BTN=1 + -D PIN_BOARD_SDA=8 + -D PIN_BOARD_SCL=7 + -D HAS_NEOPIXEL + -D NEOPIXEL_COUNT=1 + -D NEOPIXEL_DATA=21 + -D NEOPIXEL_TYPE=NEO_GRB+NEO_KHZ800 + -D SX126X_DIO2_AS_RF_SWITCH=true + -D SX126X_DIO3_TCXO_VOLTAGE=1.8 + -D SX126X_CURRENT_LIMIT=140 + -D USE_SX1262 + -D RADIO_CLASS=CustomSX1262 + -D WRAPPER_CLASS=CustomSX1262Wrapper + -D LORA_TX_POWER=22 + -D SX126X_RX_BOOSTED_GAIN=1 +build_src_filter = ${esp32_base.build_src_filter} + +<../variants/nibble_screen_connect> +lib_deps = + ${esp32_base.lib_deps} + adafruit/Adafruit SSD1306 @ ^2.5.13 + adafruit/Adafruit NeoPixel @ ^1.12.3 + +[env:nibble_screen_connect_repeater_] +extends = nibble_screen_connect_base +build_flags = + ${nibble_screen_connect_base.build_flags} + -D DISPLAY_CLASS=SSD1306Display + -D ADVERT_NAME='"Nibble Repeater"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 +build_src_filter = ${nibble_screen_connect_base.build_src_filter} + + + +<../examples/simple_repeater> +lib_deps = + ${nibble_screen_connect_base.lib_deps} + ${esp32_ota.lib_deps} + +[env:nibble_screen_connect_repeater_bridge_espnow_] +extends = nibble_screen_connect_base +build_flags = + ${nibble_screen_connect_base.build_flags} + -D DISPLAY_CLASS=SSD1306Display + -D ADVERT_NAME='"ESPNow Bridge"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 + -D WITH_ESPNOW_BRIDGE=1 +build_src_filter = ${nibble_screen_connect_base.build_src_filter} + + + + + +<../examples/simple_repeater> +lib_deps = + ${nibble_screen_connect_base.lib_deps} + ${esp32_ota.lib_deps} + +[env:nibble_screen_connect_terminal_chat_] +extends = nibble_screen_connect_base +build_flags = + ${nibble_screen_connect_base.build_flags} + -D MAX_CONTACTS=300 + -D MAX_GROUP_CHANNELS=1 +build_src_filter = ${nibble_screen_connect_base.build_src_filter} + +<../examples/simple_secure_chat/main.cpp> +lib_deps = + ${nibble_screen_connect_base.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:nibble_screen_connect_room_server_] +extends = nibble_screen_connect_base +build_flags = + ${nibble_screen_connect_base.build_flags} + -D DISPLAY_CLASS=SSD1306Display + -D ADVERT_NAME='"Nibble Room"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D ROOM_PASSWORD='"hello"' +build_src_filter = ${nibble_screen_connect_base.build_src_filter} + + + +<../examples/simple_room_server> +lib_deps = + ${nibble_screen_connect_base.lib_deps} + ${esp32_ota.lib_deps} + +[env:nibble_screen_connect_companion_radio_usb_] +extends = nibble_screen_connect_base +build_flags = + ${nibble_screen_connect_base.build_flags} + -I examples/companion_radio/ui-new + -D DISPLAY_CLASS=SSD1306Display + -D MAX_CONTACTS=300 + -D MAX_GROUP_CHANNELS=8 + -D ENABLE_USB_INTERFACE +build_src_filter = ${nibble_screen_connect_base.build_src_filter} + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${nibble_screen_connect_base.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:nibble_screen_connect_companion_radio_ble_] +extends = nibble_screen_connect_base +build_flags = + ${nibble_screen_connect_base.build_flags} + -I examples/companion_radio/ui-new + -D DISPLAY_CLASS=SSD1306Display + -D MAX_CONTACTS=300 + -D MAX_GROUP_CHANNELS=8 + -D BLE_PIN_CODE=123456 + -D BLE_DEBUG_LOGGING=1 + -D OFFLINE_QUEUE_SIZE=256 +build_src_filter = ${nibble_screen_connect_base.build_src_filter} + + + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${nibble_screen_connect_base.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:nibble_screen_connect_companion_radio_wifi_] +extends = nibble_screen_connect_base +build_flags = + ${nibble_screen_connect_base.build_flags} + -I examples/companion_radio/ui-new + -D ENABLE_WIFI_INTERFACE + -D DISPLAY_CLASS=SSD1306Display + -D MAX_CONTACTS=300 + -D MAX_GROUP_CHANNELS=8 + -D WIFI_DEBUG_LOGGING=1 + -D WIFI_SSID='"myssid"' + -D WIFI_PWD='"mypwd"' + -D OFFLINE_QUEUE_SIZE=256 +build_src_filter = ${nibble_screen_connect_base.build_src_filter} + + + + + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${nibble_screen_connect_base.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:nibble_screen_connect_kiss_modem_] +extends = nibble_screen_connect_base +build_src_filter = ${nibble_screen_connect_base.build_src_filter} + +<../examples/kiss_modem/> + +[Nano_G2_Ultra] +extends = nrf52_base +board = nano-g2-ultra +board_build.ldscript = boards/nrf52840_s140_v6.ld +build_flags = ${nrf52_base.build_flags} + -I src/helpers/nrf52 + -I lib/nrf52/s140_nrf52_6.1.1_API/include + -I lib/nrf52/s140_nrf52_6.1.1_API/include/nrf52 + -I variants/nano_g2_ultra + -D NANO_G2_ULTRA + -D RADIO_CLASS=CustomSX1262 + -D WRAPPER_CLASS=CustomSX1262Wrapper + -D LORA_TX_POWER=22 + -D SX126X_CURRENT_LIMIT=140 + -D SX126X_RX_BOOSTED_GAIN=1 + -D PIN_USER_BTN=38 +build_src_filter = ${nrf52_base.build_src_filter} + + + +<../variants/nano_g2_ultra> +debug_tool = jlink +upload_protocol = nrfutil +lib_deps = ${nrf52_base.lib_deps} + adafruit/Adafruit SH110X @ ~2.1.13 + adafruit/Adafruit GFX Library @ ^1.12.1 + stevemarple/MicroNMEA @ ^2.0.6 + +[env:Nano_G2_Ultra_repeater] +extends = Nano_G2_Ultra +build_flags = + ${Nano_G2_Ultra.build_flags} + -D DISPLAY_CLASS=SH1106Display + -D ADVERT_NAME='"Nano G2 Repeater"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 +build_src_filter = ${Nano_G2_Ultra.build_src_filter} + + + +<../examples/simple_repeater> + +[env:Nano_G2_Ultra_room_server] +extends = Nano_G2_Ultra +build_flags = + ${Nano_G2_Ultra.build_flags} + -D DISPLAY_CLASS=SH1106Display + -D ADVERT_NAME='"Nano G2 Room"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D ROOM_PASSWORD='"hello"' +build_src_filter = ${Nano_G2_Ultra.build_src_filter} + + + +<../examples/simple_room_server> + +[env:Nano_G2_Ultra_companion_radio_ble] +extends = Nano_G2_Ultra +board_build.ldscript = boards/nrf52840_s140_v6_extrafs.ld +board_upload.maximum_size = 712704 +build_flags = + ${Nano_G2_Ultra.build_flags} + -I src/helpers/ui + -I examples/companion_radio/ui-new + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D BLE_PIN_CODE=123456 + -D OFFLINE_QUEUE_SIZE=256 + -D DISPLAY_CLASS=SH1106Display + -D PIN_BUZZER=4 + -D QSPIFLASH=1 +build_src_filter = ${Nano_G2_Ultra.build_src_filter} + + + + + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = ${Nano_G2_Ultra.lib_deps} + densaugeo/base64 @ ~1.4.0 + end2endzone/NonBlockingRTTTL@^1.3.0 + +[env:Nano_G2_Ultra_companion_radio_usb] +extends = Nano_G2_Ultra +board_build.ldscript = boards/nrf52840_s140_v6_extrafs.ld +board_upload.maximum_size = 712704 +build_flags = + ${Nano_G2_Ultra.build_flags} + -I src/helpers/ui + -I examples/companion_radio/ui-new + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D QSPIFLASH=1 + -D OFFLINE_QUEUE_SIZE=256 + -D DISPLAY_CLASS=SH1106Display + -D PIN_BUZZER=4 + -D ENABLE_USB_INTERFACE +build_src_filter = ${Nano_G2_Ultra.build_src_filter} + + + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = ${Nano_G2_Ultra.lib_deps} + densaugeo/base64 @ ~1.4.0 + end2endzone/NonBlockingRTTTL@^1.3.0 + +[env:Nano_G2_Ultra_kiss_modem] +extends = Nano_G2_Ultra +build_src_filter = ${Nano_G2_Ultra.build_src_filter} + +<../examples/kiss_modem/> + +[GAT562_Mesh_Tracker_Pro] +extends = nrf52_base +board = rak4631 +board_check = true +build_flags = ${nrf52_base.build_flags} + ${sensor_base.build_flags} + -I variants/gat562_mesh_tracker_pro + -D PIN_BOARD_SCL=14 + -D PIN_BOARD_SDA=13 + -D PIN_OLED_RESET=-1 + -D UI_HAS_JOYSTICK=1 + -D RADIO_CLASS=CustomSX1262 + -D WRAPPER_CLASS=CustomSX1262Wrapper + -D LORA_TX_POWER=22 + -D SX126X_CURRENT_LIMIT=140 + -D SX126X_RX_BOOSTED_GAIN=1 +build_src_filter = ${nrf52_base.build_src_filter} + +<../variants/gat562_mesh_tracker_pro> + + + + + + +lib_deps = + ${nrf52_base.lib_deps} + ${sensor_base.lib_deps} + adafruit/Adafruit SSD1306 @ ^2.5.13 + sparkfun/SparkFun u-blox GNSS Arduino Library@^2.2.27 + +[env:GAT562_Mesh_Tracker_Pro_repeater] +extends = GAT562_Mesh_Tracker_Pro +build_flags = + ${GAT562_Mesh_Tracker_Pro.build_flags} + -D DISPLAY_CLASS=SSD1306Display + -D ADVERT_NAME='"GAT562 Repeater"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 +build_src_filter = ${GAT562_Mesh_Tracker_Pro.build_src_filter} + + + +<../examples/simple_repeater> + +[env:GAT562_Mesh_Tracker_Pro_room_server] +extends = GAT562_Mesh_Tracker_Pro +build_flags = + ${GAT562_Mesh_Tracker_Pro.build_flags} + -D DISPLAY_CLASS=SSD1306Display + -D ADVERT_NAME='"GAT562 Room"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D ROOM_PASSWORD='"hello"' +build_src_filter = ${GAT562_Mesh_Tracker_Pro.build_src_filter} + + + +<../examples/simple_room_server> + +[env:GAT562_Mesh_Tracker_Pro_companion_radio_usb] +extends = GAT562_Mesh_Tracker_Pro +board_build.ldscript = boards/nrf52840_s140_v6_extrafs.ld +board_upload.maximum_size = 712704 +build_flags = + ${GAT562_Mesh_Tracker_Pro.build_flags} + -I examples/companion_radio/ui-new + -D DISPLAY_CLASS=SSD1306Display + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D ENABLE_USB_INTERFACE +build_src_filter = ${GAT562_Mesh_Tracker_Pro.build_src_filter} + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${GAT562_Mesh_Tracker_Pro.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:GAT562_Mesh_Tracker_Pro_companion_radio_ble] +extends = GAT562_Mesh_Tracker_Pro +board_build.ldscript = boards/nrf52840_s140_v6_extrafs.ld +board_upload.maximum_size = 712704 +build_flags = + ${GAT562_Mesh_Tracker_Pro.build_flags} + -I examples/companion_radio/ui-new + -D DISPLAY_CLASS=SSD1306Display + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D BLE_PIN_CODE=123456 + -D BLE_DEBUG_LOGGING=1 + -D OFFLINE_QUEUE_SIZE=256 +build_src_filter = ${GAT562_Mesh_Tracker_Pro.build_src_filter} + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${GAT562_Mesh_Tracker_Pro.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:GAT562_Mesh_Tracker_Pro_kiss_modem] +extends = GAT562_Mesh_Tracker_Pro +build_src_filter = ${GAT562_Mesh_Tracker_Pro.build_src_filter} + +<../examples/kiss_modem/> + +[R1Neo] +extends = nrf52_base +board = rak4631 +board_check = true +build_flags = ${nrf52_base.build_flags} + ${sensor_base.build_flags} + -I variants/muziworks_r1_neo + -I src/helpers/ui + -D R1Neo + -D RADIO_CLASS=CustomSX1262 + -D WRAPPER_CLASS=CustomSX1262Wrapper + -D DISPLAY_CLASS=NullDisplayDriver + -D LORA_TX_POWER=22 + -D SX126X_CURRENT_LIMIT=140 + -D SX126X_RX_BOOSTED_GAIN=1 + -D PIN_BUZZER=3 + -D PIN_USER_BTN=26 + -D USER_BTN_PRESSED=HIGH + -D PIN_GPS_TX=25 + -D PIN_GPS_RX=24 + -D PIN_GPS_EN=33 +build_src_filter = ${nrf52_base.build_src_filter} + +<../variants/muziworks_r1_neo> + + + + + + +lib_deps = + ${nrf52_base.lib_deps} + ${sensor_base.lib_deps} + sparkfun/SparkFun u-blox GNSS Arduino Library@^2.2.27 + +[env:R1Neo_repeater] +extends = R1Neo +build_flags = + ${R1Neo.build_flags} + -D ADVERT_NAME='"R1 Neo Repeater"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 +build_src_filter = ${R1Neo.build_src_filter} + +<../examples/simple_repeater> + +[env:R1Neo_room_server] +extends = R1Neo +build_flags = + ${R1Neo.build_flags} + -D ADVERT_NAME='"R1 Neo Test Room"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D ROOM_PASSWORD='"hello"' +build_src_filter = ${R1Neo.build_src_filter} + +<../examples/simple_room_server> + +[env:R1Neo_companion_radio_usb] +extends = R1Neo +board_build.ldscript = boards/nrf52840_s140_v6_extrafs.ld +board_upload.maximum_size = 712704 +build_flags = + ${R1Neo.build_flags} + -I examples/companion_radio/ui-orig + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D ENABLE_USB_INTERFACE +build_src_filter = ${R1Neo.build_src_filter} + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-orig/*.cpp> +lib_deps = + ${R1Neo.lib_deps} + densaugeo/base64 @ ~1.4.0 + end2endzone/NonBlockingRTTTL@^1.3.0 + +[env:R1Neo_companion_radio_ble] +extends = R1Neo +board_build.ldscript = boards/nrf52840_s140_v6_extrafs.ld +board_upload.maximum_size = 712704 +build_flags = + ${R1Neo.build_flags} + -I examples/companion_radio/ui-orig + -D ENV_INCLUDE_GPS=1 + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D BLE_PIN_CODE=123456 + -D BLE_DEBUG_LOGGING=1 + -D OFFLINE_QUEUE_SIZE=256 +build_src_filter = ${R1Neo.build_src_filter} + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-orig/*.cpp> +lib_deps = + ${R1Neo.lib_deps} + densaugeo/base64 @ ~1.4.0 + end2endzone/NonBlockingRTTTL@^1.3.0 + +[env:R1Neo_terminal_chat] +extends = R1Neo +build_flags = + ${R1Neo.build_flags} + -D MAX_CONTACTS=100 + -D MAX_GROUP_CHANNELS=1 +build_src_filter = ${R1Neo.build_src_filter} + +<../examples/simple_secure_chat/main.cpp> +lib_deps = + ${R1Neo.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:R1Neo_sensor] +extends = R1Neo +build_flags = + ${R1Neo.build_flags} + -D DISPLAY_CLASS=SSD1306Display + -D ADVERT_NAME='"R1 Neo Sensor"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' +build_src_filter = ${R1Neo.build_src_filter} + +<../examples/simple_sensor> + +[env:R1Neo_kiss_modem] +extends = R1Neo +build_src_filter = ${R1Neo.build_src_filter} + +<../examples/kiss_modem/> + +[Heltec_tower_v2] +extends = nrf52_base +board = heltec_tower_v2 +board_build.ldscript = boards/nrf52840_s140_v6.ld +build_flags = ${nrf52_base.build_flags} + -D ENV_INCLUDE_GPS=1 + -I lib/nrf52/s140_nrf52_6.1.1_API/include + -I lib/nrf52/s140_nrf52_6.1.1_API/include/nrf52 + -I variants/heltec_tower_v2 + -D HELTEC_TOWER_V2 + -D NRF52_POWER_MANAGEMENT + -D RADIO_CLASS=CustomSX1262 + -D WRAPPER_CLASS=CustomSX1262Wrapper + -D LORA_TX_POWER=12 + -D MAX_LORA_TX_POWER=22 + -D SX126X_CURRENT_LIMIT=140 + -D SX126X_RX_BOOSTED_GAIN=1 +build_src_filter = ${nrf52_base.build_src_filter} + + + + + +<../variants/heltec_tower_v2> +lib_deps = + ${nrf52_base.lib_deps} + stevemarple/MicroNMEA @ ^2.0.6 +debug_tool = jlink +upload_protocol = nrfutil + +[env:Heltec_tower_v2_repeater] +extends = Heltec_tower_v2 +build_src_filter = ${Heltec_tower_v2.build_src_filter} + +<../examples/simple_repeater> +build_flags = + ${Heltec_tower_v2.build_flags} + -D ADVERT_NAME='"Heltec_Tower_V2 Repeater"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 + +[env:Heltec_tower_v2_room_server] +extends = Heltec_tower_v2 +build_src_filter = ${Heltec_tower_v2.build_src_filter} + +<../examples/simple_room_server> +build_flags = + ${Heltec_tower_v2.build_flags} + -D ADVERT_NAME='"Heltec_Tower_V2 Room"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D ROOM_PASSWORD='"hello"' + +[env:Heltec_tower_v2_companion_radio_ble] +extends = Heltec_tower_v2 +board_build.ldscript = boards/nrf52840_s140_v6_extrafs.ld +board_upload.maximum_size = 712704 +build_flags = + ${Heltec_tower_v2.build_flags} + -I examples/companion_radio/ui-new + -D DISPLAY_CLASS=NullDisplayDriver + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D BLE_PIN_CODE=123456 + -D OFFLINE_QUEUE_SIZE=256 +build_src_filter = ${Heltec_tower_v2.build_src_filter} + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${Heltec_tower_v2.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:Heltec_tower_v2_companion_radio_usb] +extends = Heltec_tower_v2 +board_build.ldscript = boards/nrf52840_s140_v6_extrafs.ld +board_upload.maximum_size = 712704 +build_flags = + ${Heltec_tower_v2.build_flags} + -I examples/companion_radio/ui-new + -D DISPLAY_CLASS=NullDisplayDriver + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D ENABLE_USB_INTERFACE +build_src_filter = ${Heltec_tower_v2.build_src_filter} + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${Heltec_tower_v2.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:Heltec_tower_v2_kiss_modem] +extends = Heltec_tower_v2 +build_src_filter = ${Heltec_tower_v2.build_src_filter} + +<../examples/kiss_modem/> + +[ThinkNode_M2] +extends = esp32_base +board = ESP32-S3-WROOM-1-N4 +build_flags = ${esp32_base.build_flags} + -I variants/thinknode_m2 + -D THINKNODE_M2 + -D GPS_RX=44 + -D GPS_TX=43 + -D PIN_VEXT_EN=46 + -D PIN_BUZZER=5 + -D PIN_VEXT_EN_ACTIVE=HIGH + -D PIN_BOARD_SCL=15 + -D PIN_BOARD_SDA=16 + -D P_LORA_DIO_1=3 + -D P_LORA_NSS=10 + -D P_LORA_RESET=21 + -D P_LORA_BUSY=14 + -D P_LORA_SCLK=12 + -D P_LORA_MISO=13 + -D P_LORA_MOSI=11 + -D PIN_USER_BTN=47 + -D PIN_STATUS_LED=6 + -D PIN_LED=6 + -D SX126X_DIO2_AS_RF_SWITCH=true + -D SX126X_DIO3_TCXO_VOLTAGE=3.3 + -D SX126X_CURRENT_LIMIT=140 + -D DISPLAY_CLASS=SH1106Display + -D USE_SX1262 + -D RADIO_CLASS=CustomSX1262 + -D WRAPPER_CLASS=CustomSX1262Wrapper + -D LORA_TX_POWER=22 + -D SX126X_RX_BOOSTED_GAIN=1 +build_src_filter = ${esp32_base.build_src_filter} + + + + + +<../variants/thinknode_m2> +lib_deps = ${esp32_base.lib_deps} + adafruit/Adafruit SH110X @ ~2.1.13 + adafruit/Adafruit GFX Library @ ^1.12.1 + +[env:ThinkNode_M2_Repeater] +extends = ThinkNode_M2 +build_src_filter = ${ThinkNode_M2.build_src_filter} + +<../examples/simple_repeater/*.cpp> +build_flags = + ${ThinkNode_M2.build_flags} + -D ADVERT_NAME='"Thinknode M2 Repeater"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=8 +lib_deps = + ${ThinkNode_M2.lib_deps} + ${esp32_ota.lib_deps} + +[env:ThinkNode_M2_Repeater_bridge_espnow] +extends = ThinkNode_M2 +build_src_filter = ${ThinkNode_M2.build_src_filter} + + + +<../examples/simple_repeater/*.cpp> +build_flags = + ${ThinkNode_M2.build_flags} + -D ADVERT_NAME='"ESPNow Bridge"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=8 + -D WITH_ESPNOW_BRIDGE=1 + -D WITH_ESPNOW_BRIDGE_SECRET='"shared-secret"' +lib_deps = + ${ThinkNode_M2.lib_deps} + ${esp32_ota.lib_deps} + +[env:ThinkNode_M2_room_server] +extends = ThinkNode_M2 +build_src_filter = ${ThinkNode_M2.build_src_filter} + +<../examples/simple_room_server> +build_flags = + ${ThinkNode_M2.build_flags} + -D ADVERT_NAME='"Thinknode M2 Room Server"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D ROOM_PASSWORD='"hello"' +lib_deps = + ${ThinkNode_M2.lib_deps} + ${esp32_ota.lib_deps} + +[env:ThinkNode_M2_terminal_chat] +extends = ThinkNode_M2 +build_flags = + ${ThinkNode_M2.build_flags} + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 +build_src_filter = ${ThinkNode_M2.build_src_filter} + +<../examples/simple_secure_chat/main.cpp> +lib_deps = + ${ThinkNode_M2.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:ThinkNode_M2_companion_radio_ble] +extends = ThinkNode_M2 +build_flags = + ${ThinkNode_M2.build_flags} + -I examples/companion_radio/ui-new + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D BLE_PIN_CODE=123456 + -D OFFLINE_QUEUE_SIZE=256 +build_src_filter = ${ThinkNode_M2.build_src_filter} + + + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${ThinkNode_M2.lib_deps} + densaugeo/base64 @ ~1.4.0 + end2endzone/NonBlockingRTTTL@^1.3.0 + +[env:ThinkNode_M2_companion_radio_usb] +extends = ThinkNode_M2 +build_flags = + ${ThinkNode_M2.build_flags} + -I examples/companion_radio/ui-new + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D OFFLINE_QUEUE_SIZE=256 + -D ENABLE_USB_INTERFACE +build_src_filter = ${ThinkNode_M2.build_src_filter} + + + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${ThinkNode_M2.lib_deps} + densaugeo/base64 @ ~1.4.0 + end2endzone/NonBlockingRTTTL@^1.3.0 + +[env:ThinkNode_M2_companion_radio_wifi] +extends = ThinkNode_M2 +build_flags = + ${ThinkNode_M2.build_flags} + -I examples/companion_radio/ui-new + -D ENABLE_WIFI_INTERFACE + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D OFFLINE_QUEUE_SIZE=256 + -D WIFI_DEBUG_LOGGING=1 + -D WIFI_SSID='"myssid"' + -D WIFI_PWD='"mypwd"' +build_src_filter = ${ThinkNode_M2.build_src_filter} + + + + + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${ThinkNode_M2.lib_deps} + densaugeo/base64 @ ~1.4.0 + end2endzone/NonBlockingRTTTL@^1.3.0 + +[env:ThinkNode_M2_companion_radio_serial] +extends = ThinkNode_M2 +build_flags = + ${ThinkNode_M2.build_flags} + -I examples/companion_radio/ui-new + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D SERIAL_TX=43 + -D SERIAL_RX=44 +build_src_filter = ${ThinkNode_M2.build_src_filter} + + + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${ThinkNode_M2.lib_deps} + densaugeo/base64 @ ~1.4.0 + end2endzone/NonBlockingRTTTL@^1.3.0 + +[env:ThinkNode_M2_kiss_modem] +extends = ThinkNode_M2 +build_flags = ${ThinkNode_M2.build_flags} + -UPIN_BUZZER +build_src_filter = ${ThinkNode_M2.build_src_filter} + +<../examples/kiss_modem/> + +[ThinkNode_M5] +extends = esp32_base +board = ESP32-S3-WROOM-1-N4 +build_flags = ${esp32_base.build_flags} + -I variants/thinknode_m5 + -I src/helpers/sensors + -D THINKNODE_M5 + -D PIN_BUZZER=9 + -D PIN_BOARD_SCL=1 + -D PIN_BOARD_SDA=2 + -D P_LORA_EN=46 + -D P_LORA_DIO_1=4 + -D P_LORA_NSS=17 + -D P_LORA_RESET=6 + -D P_LORA_BUSY=5 + -D P_LORA_SCLK=16 + -D P_LORA_MISO=7 + -D P_LORA_MOSI=15 + -D PIN_USER_BTN=21 + -D PIN_BUTTON2=14 + -D EXP_PIN_LED=1 + -D DISPLAY_ROTATION=4 + -D DISPLAY_CLASS=GxEPDDisplay + -D EINK_DISPLAY_MODEL=GxEPD2_154_D67 + -D EINK_SCALE_X=1.5625f + -D EINK_SCALE_Y=1.5625f + -D EINK_X_OFFSET=0 + -D EINK_Y_OFFSET=10 + -D UI_RECENT_LIST_SIZE=9 + -D UI_MSG_PREVIEW_SIZE=165 + -D EINK_MAX_PARTIAL_REFRESH=60 + -D BACKLIGHT_BTN=PIN_BUTTON2 + -D AUTO_OFF_MILLIS=900000 + -D UI_NO_HIBERNATE + -D DISABLE_DIAGNOSTIC_OUTPUT + -D SX126X_DIO2_AS_RF_SWITCH=true + -D SX126X_DIO3_TCXO_VOLTAGE=3.3 + -D SX126X_CURRENT_LIMIT=140 + -D USE_SX1262 + -D RADIO_CLASS=CustomSX1262 + -D WRAPPER_CLASS=CustomSX1262Wrapper + -D LORA_TX_POWER=22 + -D SX126X_RX_BOOSTED_GAIN=1 + -D ENV_INCLUDE_GPS=1 + -D PERSISTANT_GPS=1 + -D ENV_SKIP_GPS_DETECT=1 +build_src_filter = ${esp32_base.build_src_filter} + + + + + + + +<../variants/thinknode_m5> +lib_deps = ${esp32_base.lib_deps} + zinggjm/GxEPD2 @ 1.6.2 + bakercp/CRC32 @ ^2.0.0 + maxpromer/PCA9557-arduino + stevemarple/MicroNMEA @ ^2.0.6 + +[env:ThinkNode_M5_Repeater] +extends = ThinkNode_M5 +build_src_filter = ${ThinkNode_M5.build_src_filter} + +<../examples/simple_repeater/*.cpp> +build_flags = + ${ThinkNode_M5.build_flags} + -D ADVERT_NAME='"Thinknode M5 Repeater"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=8 +lib_deps = + ${ThinkNode_M5.lib_deps} + ${esp32_ota.lib_deps} + +[env:ThinkNode_M5_Repeater_bridge_espnow] +extends = ThinkNode_M5 +build_src_filter = ${ThinkNode_M5.build_src_filter} + + + +<../examples/simple_repeater/*.cpp> +build_flags = + ${ThinkNode_M5.build_flags} + -D ADVERT_NAME='"ESPNow Bridge"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=8 + -D WITH_ESPNOW_BRIDGE=1 + -D WITH_ESPNOW_BRIDGE_SECRET='"shared-secret"' +lib_deps = + ${ThinkNode_M5.lib_deps} + ${esp32_ota.lib_deps} + +[env:ThinkNode_M5_room_server] +extends = ThinkNode_M5 +build_src_filter = ${ThinkNode_M5.build_src_filter} + +<../examples/simple_room_server> +build_flags = + ${ThinkNode_M5.build_flags} + -D ADVERT_NAME='"Thinknode M5 Room Server"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D ROOM_PASSWORD='"hello"' +lib_deps = + ${ThinkNode_M5.lib_deps} + ${esp32_ota.lib_deps} + +[env:ThinkNode_M5_terminal_chat] +extends = ThinkNode_M5 +build_flags = + ${ThinkNode_M5.build_flags} + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 +build_src_filter = ${ThinkNode_M5.build_src_filter} + +<../examples/simple_secure_chat/main.cpp> +lib_deps = + ${ThinkNode_M5.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:ThinkNode_M5_companion_radio_ble] +extends = ThinkNode_M5 +build_flags = + ${ThinkNode_M5.build_flags} + -I examples/companion_radio/ui-new + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D BLE_PIN_CODE=123456 + -D OFFLINE_QUEUE_SIZE=256 +build_src_filter = ${ThinkNode_M5.build_src_filter} + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> + + +lib_deps = + ${ThinkNode_M5.lib_deps} + densaugeo/base64 @ ~1.4.0 + end2endzone/NonBlockingRTTTL@^1.3.0 + +[env:ThinkNode_M5_companion_radio_usb] +extends = ThinkNode_M5 +build_flags = + ${ThinkNode_M5.build_flags} + -I examples/companion_radio/ui-new + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D OFFLINE_QUEUE_SIZE=256 + -D ENABLE_USB_INTERFACE + -D ENABLE_WIFI_INTERFACE +build_src_filter = ${ThinkNode_M5.build_src_filter} + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> + + + + +lib_deps = + ${ThinkNode_M5.lib_deps} + densaugeo/base64 @ ~1.4.0 + end2endzone/NonBlockingRTTTL@^1.3.0 + +[env:ThinkNode_M5_companion_radio_wifi] +extends = ThinkNode_M5 +build_flags = + ${ThinkNode_M5.build_flags} + -I examples/companion_radio/ui-new + -D ENABLE_WIFI_INTERFACE + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D OFFLINE_QUEUE_SIZE=256 + -D WIFI_DEBUG_LOGGING=1 + -D WIFI_SSID='"myssid"' + -D WIFI_PWD='"mypwd"' +build_src_filter = ${ThinkNode_M5.build_src_filter} + + + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> + + +lib_deps = + ${ThinkNode_M5.lib_deps} + densaugeo/base64 @ ~1.4.0 + end2endzone/NonBlockingRTTTL@^1.3.0 + +[env:ThinkNode_M5_companion_radio_serial] +extends = ThinkNode_M5 +build_flags = + ${ThinkNode_M5.build_flags} + -I examples/companion_radio/ui-new + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D SERIAL_TX=D6 + -D SERIAL_RX=D7 +build_src_filter = ${ThinkNode_M5.build_src_filter} + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> + + +lib_deps = + ${ThinkNode_M5.lib_deps} + densaugeo/base64 @ ~1.4.0 + end2endzone/NonBlockingRTTTL@^1.3.0 + +[env:ThinkNode_M5_kiss_modem] +extends = ThinkNode_M5 +build_src_filter = ${ThinkNode_M5.build_src_filter} + +<../examples/kiss_modem/> + +[GAT562_Mesh_EVB_Pro] +extends = nrf52_base +board = rak4631 +board_check = true +build_flags = ${nrf52_base.build_flags} + ${sensor_base.build_flags} + -I variants/gat562_mesh_evb_pro + -D PIN_BOARD_SCL=14 + -D PIN_BOARD_SDA=13 + -D RADIO_CLASS=CustomSX1262 + -D WRAPPER_CLASS=CustomSX1262Wrapper + -D LORA_TX_POWER=22 + -D SX126X_CURRENT_LIMIT=140 + -D SX126X_RX_BOOSTED_GAIN=1 +build_src_filter = ${nrf52_base.build_src_filter} + +<../variants/gat562_mesh_evb_pro> + + + + +lib_deps = + ${nrf52_base.lib_deps} + ${sensor_base.lib_deps} + sparkfun/SparkFun u-blox GNSS Arduino Library@^2.2.27 + +[env:GAT562_Mesh_EVB_Pro_repeater] +extends = GAT562_Mesh_EVB_Pro +build_flags = + ${GAT562_Mesh_EVB_Pro.build_flags} + -D ADVERT_NAME='"GAT562 EVB Pro Repeater"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 +build_src_filter = ${GAT562_Mesh_EVB_Pro.build_src_filter} + +<../examples/simple_repeater> + +[env:GAT562_Mesh_EVB_Pro_room_server] +extends = GAT562_Mesh_EVB_Pro +build_flags = + ${GAT562_Mesh_EVB_Pro.build_flags} + -D ADVERT_NAME='"GAT562 EVB Pro Room Server"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D ROOM_PASSWORD='"hello"' +build_src_filter = ${GAT562_Mesh_EVB_Pro.build_src_filter} + +<../examples/simple_room_server> + +[env:GAT562_Mesh_EVB_Pro_kiss_modem] +extends = GAT562_Mesh_EVB_Pro +build_src_filter = ${GAT562_Mesh_EVB_Pro.build_src_filter} + +<../examples/kiss_modem/> + +[Heltec_t1] +extends = nrf52_base +board = heltec_t1 +board_build.ldscript = boards/nrf52840_s140_v6.ld +build_flags = ${nrf52_base.build_flags} + ${sensor_base.build_flags} + -I lib/nrf52/s140_nrf52_6.1.1_API/include + -I lib/nrf52/s140_nrf52_6.1.1_API/include/nrf52 + -I variants/heltec_t1 + -I src/helpers/ui + -D HELTEC_T1 + -D NRF52_POWER_MANAGEMENT + -D RADIO_CLASS=CustomSX1262 + -D WRAPPER_CLASS=CustomSX1262Wrapper + -D LORA_TX_POWER=22 + -D DISPLAY_CLASS=ST7735Display +build_src_filter = ${nrf52_base.build_src_filter} + + + + + +<../variants/heltec_t1> + + + + +lib_deps = + ${nrf52_base.lib_deps} + ${sensor_base.lib_deps} + bodmer/TFT_eSPI @ ^2.4.31 +debug_tool = jlink +upload_protocol = nrfutil + +[env:Heltec_t1_repeater] +extends = Heltec_t1 +build_src_filter = ${Heltec_t1.build_src_filter} + +<../examples/simple_repeater> +build_flags = + ${Heltec_t1.build_flags} + -D ADVERT_NAME='"Heltec_t1 Repeater"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 + +[env:Heltec_t1_room_server] +extends = Heltec_t1 +build_src_filter = ${Heltec_t1.build_src_filter} + +<../examples/simple_room_server> +build_flags = + ${Heltec_t1.build_flags} + -D ADVERT_NAME='"Heltec_t1 Room"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D ROOM_PASSWORD='"hello"' + +[env:Heltec_t1_companion_radio_ble] +extends = Heltec_t1 +board_build.ldscript = boards/nrf52840_s140_v6_extrafs.ld +board_upload.maximum_size = 712704 +build_flags = + ${Heltec_t1.build_flags} + -I examples/companion_radio/ui-new + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D BLE_PIN_CODE=123456 + -D ENV_INCLUDE_GPS=1 + -D OFFLINE_QUEUE_SIZE=256 +build_src_filter = ${Heltec_t1.build_src_filter} + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${Heltec_t1.lib_deps} + densaugeo/base64 @ ~1.4.0 + end2endzone/NonBlockingRTTTL@^1.3.0 + +[env:Heltec_t1_companion_radio_usb] +extends = Heltec_t1 +board_build.ldscript = boards/nrf52840_s140_v6_extrafs.ld +board_upload.maximum_size = 712704 +build_flags = + ${Heltec_t1.build_flags} + -I examples/companion_radio/ui-new + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D ENABLE_USB_INTERFACE +build_src_filter = ${Heltec_t1.build_src_filter} + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${Heltec_t1.lib_deps} + densaugeo/base64 @ ~1.4.0 + end2endzone/NonBlockingRTTTL@^1.3.0 + +[env:Heltec_t1_kiss_modem] +extends = Heltec_t1 +build_src_filter = ${Heltec_t1.build_src_filter} + +<../examples/kiss_modem/> + +[ThinkNode_M4] +extends = nrf52_base +board = thinknode_m4 +board_build.ldscript = boards/nrf52840_s140_v6.ld +build_flags = ${nrf52_base.build_flags} + -I src/helpers/nrf52 + -I lib/nrf52/s140_nrf52_6.1.1_API/include + -I lib/nrf52/s140_nrf52_6.1.1_API/include/nrf52 + -I variants/thinknode_m4 + -I src/helpers/ui + -D THINKNODE_M4 + -D PIN_USER_BTN=4 + -D PIN_STATUS_LED=LED_STATUS + -D RADIO_CLASS=CustomLR1110 + -D WRAPPER_CLASS=CustomLR1110Wrapper + -D LORA_TX_POWER=22 + -D RF_SWITCH_TABLE + -D RX_BOOSTED_GAIN=true + -D P_LORA_BUSY=26 + -D P_LORA_SCLK=6 + -D P_LORA_NSS=27 + -D P_LORA_DIO_1=12 + -D P_LORA_MISO=8 + -D P_LORA_MOSI=7 + -D P_LORA_RESET=40 + -D P_LORA_TX_LED=LED_TX + -D LR11X0_DIO_AS_RF_SWITCH=true + -D LR11X0_DIO3_TCXO_VOLTAGE=1.6 + -D ENV_INCLUDE_GPS=1 +build_src_filter = ${nrf52_base.build_src_filter} + + + +<../variants/thinknode_m4> + + +debug_tool = stlink +upload_protocol = nrfutil +lib_deps = ${nrf52_base.lib_deps} + +[env:ThinkNode_M4_repeater] +extends = ThinkNode_M4 +build_flags = ${ThinkNode_M4.build_flags} + -I examples/companion_radio/ui-orig + -D ADVERT_NAME='"ThinkNode_M4 Repeater"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 +build_src_filter = ${ThinkNode_M4.build_src_filter} + +<../examples/simple_repeater> +lib_deps = ${ThinkNode_M4.lib_deps} + stevemarple/MicroNMEA @ ^2.0.6 + +[env:ThinkNode_M4_room_server] +extends = ThinkNode_M4 +build_flags = ${ThinkNode_M4.build_flags} + -I examples/companion_radio/ui-orig + -D ADVERT_NAME='"ThinkNode_M4 Room"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D ROOM_PASSWORD='"hello"' + -D RF_SWITCH_TABLE +build_src_filter = ${ThinkNode_M4.build_src_filter} + +<../examples/simple_room_server> +lib_deps = ${ThinkNode_M4.lib_deps} + stevemarple/MicroNMEA @ ^2.0.6 + +[env:ThinkNode_M4_companion_radio_usb] +extends = ThinkNode_M4 +board_build.ldscript = boards/nrf52840_s140_v6_extrafs.ld +board_upload.maximum_size = 708608 +build_flags = ${ThinkNode_M4.build_flags} + -I examples/companion_radio/ui-orig + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D OFFLINE_QUEUE_SIZE=256 + -D DISPLAY_CLASS=NullDisplayDriver + -D PIN_BUZZER=23 + -D PIN_BUZZER_EN=36 + -D ENABLE_USB_INTERFACE +build_src_filter = ${ThinkNode_M4.build_src_filter} + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-orig/*.cpp> +lib_deps = ${ThinkNode_M4.lib_deps} + densaugeo/base64 @ ~1.4.0 + stevemarple/MicroNMEA @ ^2.0.6 + end2endzone/NonBlockingRTTTL@^1.3.0 + +[env:ThinkNode_M4_companion_radio_ble] +extends = ThinkNode_M4 +board_build.ldscript = boards/nrf52840_s140_v6_extrafs.ld +board_upload.maximum_size = 708608 +build_flags = ${ThinkNode_M4.build_flags} + -I examples/companion_radio/ui-orig + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D BLE_PIN_CODE=123456 + -D BLE_TX_POWER=0 + -D OFFLINE_QUEUE_SIZE=256 + -D DISPLAY_CLASS=NullDisplayDriver + -D PIN_BUZZER=23 + -D PIN_BUZZER_EN=36 +build_src_filter = ${ThinkNode_M4.build_src_filter} + + + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-orig/*.cpp> +lib_deps = ${ThinkNode_M4.lib_deps} + densaugeo/base64 @ ~1.4.0 + stevemarple/MicroNMEA @ ^2.0.6 + end2endzone/NonBlockingRTTTL@^1.3.0 + +[env:ThinkNode_M4_kiss_modem] +extends = ThinkNode_M4 +build_src_filter = ${ThinkNode_M4.build_src_filter} + +<../examples/kiss_modem/> +lib_deps = ${ThinkNode_M4.lib_deps} + stevemarple/MicroNMEA @ ^2.0.6 + +[lora_e5] +extends = stm32_base +board = lora_e5_dev_board +board_upload.maximum_size = 229376 +build_flags = ${stm32_base.build_flags} + -D RADIO_CLASS=CustomSTM32WLx + -D WRAPPER_CLASS=CustomSTM32WLxWrapper + -D LORA_TX_POWER=22 + -D SX126X_CURRENT_LIMIT=140 + -D SPI_INTERFACES_COUNT=0 + -D RX_BOOSTED_GAIN=true + -D PIN_SERIAL_RX=PB7 + -D PIN_SERIAL_TX=PB6 + -I variants/wio-e5-dev +build_src_filter = ${stm32_base.build_src_filter} + +<../variants/wio-e5-dev> + +[env:wio-e5_repeater] +extends = lora_e5 +build_flags = ${lora_e5.build_flags} + -D LORA_TX_POWER=22 + -D ADVERT_NAME='"WIO-E5 Repeater"' + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 +build_src_filter = ${lora_e5.build_src_filter} + +<../examples/simple_repeater/*.cpp> + +[env:wio-e5-repeater_bridge_rs232] +extends = lora_e5 +build_flags = ${lora_e5.build_flags} + -D LORA_TX_POWER=22 + -D ADVERT_NAME='"WIO-E5 Repeater"' + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 + -D ENABLE_HWSERIAL2 + -D WITH_RS232_BRIDGE=Serial2 + -D WITH_RS232_BRIDGE_RX=PA3 + -D WITH_RS232_BRIDGE_TX=PA2 +build_src_filter = ${lora_e5.build_src_filter} + + + +<../examples/simple_repeater/*.cpp> + +[env:wio-e5_companion_radio_usb] +extends = lora_e5 +build_flags = ${lora_e5.build_flags} + -D LORA_TX_POWER=22 + -D MAX_CONTACTS=100 + -D MAX_GROUP_CHANNELS=8 + -D ENABLE_USB_INTERFACE +build_src_filter = ${lora_e5.build_src_filter} + +<../examples/companion_radio/*.cpp> +lib_deps = ${lora_e5.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:wio-e5_kiss_modem] +extends = lora_e5 +build_src_filter = ${lora_e5.build_src_filter} + +<../examples/kiss_modem/> + +[ThinkNode_M3] +extends = nrf52_base +board = thinknode_m3 +board_build.ldscript = boards/nrf52840_s140_v6.ld +build_flags = ${nrf52_base.build_flags} + -I src/helpers/nrf52 + -I lib/nrf52/s140_nrf52_6.1.1_API/include + -I lib/nrf52/s140_nrf52_6.1.1_API/include/nrf52 + -I variants/thinknode_m3 + -I src/helpers/ui + -D THINKNODE_M3 + -D PIN_USER_BTN=12 + -D PIN_STATUS_LED=35 + -D RADIO_CLASS=CustomLR1110 + -D WRAPPER_CLASS=CustomLR1110Wrapper + -D LORA_TX_POWER=22 + -D RF_SWITCH_TABLE + -D RX_BOOSTED_GAIN=true + -D P_LORA_BUSY=43 + -D P_LORA_SCLK=45 + -D P_LORA_NSS=44 + -D P_LORA_DIO_1=40 + -D P_LORA_MISO=47 + -D P_LORA_MOSI=46 + -D P_LORA_RESET=42 + -D P_LORA_TX_LED=PIN_LED_BLUE + -D LR11X0_DIO_AS_RF_SWITCH=true + -D LR11X0_DIO3_TCXO_VOLTAGE=3.3 + -D ENV_INCLUDE_GPS=1 +build_src_filter = ${nrf52_base.build_src_filter} + + + +<../variants/thinknode_m3> + + +debug_tool = stlink +upload_protocol = nrfutil +lib_deps = ${nrf52_base.lib_deps} + +[env:ThinkNode_M3_repeater] +extends = ThinkNode_M3 +build_flags = ${ThinkNode_M3.build_flags} + -I examples/companion_radio/ui-orig + -D ADVERT_NAME='"ThinkNode_M3 Repeater"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 +build_src_filter = ${ThinkNode_M3.build_src_filter} + +<../examples/simple_repeater> +lib_deps = ${ThinkNode_M3.lib_deps} + stevemarple/MicroNMEA @ ^2.0.6 + +[env:ThinkNode_M3_room_server] +extends = ThinkNode_M3 +build_flags = ${ThinkNode_M3.build_flags} + -I examples/companion_radio/ui-orig + -D ADVERT_NAME='"ThinkNode_M3 Room"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D ROOM_PASSWORD='"hello"' + -D RF_SWITCH_TABLE +build_src_filter = ${ThinkNode_M3.build_src_filter} + +<../examples/simple_room_server> +lib_deps = ${ThinkNode_M3.lib_deps} + stevemarple/MicroNMEA @ ^2.0.6 + +[env:ThinkNode_M3_companion_radio_usb] +extends = ThinkNode_M3 +board_build.ldscript = boards/nrf52840_s140_v6_extrafs.ld +board_upload.maximum_size = 708608 +build_flags = ${ThinkNode_M3.build_flags} + -I examples/companion_radio/ui-orig + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D OFFLINE_QUEUE_SIZE=256 + -D DISPLAY_CLASS=NullDisplayDriver + -D PIN_BUZZER=23 + -D PIN_BUZZER_EN=36 + -D ENABLE_USB_INTERFACE +build_src_filter = ${ThinkNode_M3.build_src_filter} + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-orig/*.cpp> +lib_deps = ${ThinkNode_M3.lib_deps} + densaugeo/base64 @ ~1.4.0 + stevemarple/MicroNMEA @ ^2.0.6 + end2endzone/NonBlockingRTTTL@^1.3.0 + +[env:ThinkNode_M3_companion_radio_ble] +extends = ThinkNode_M3 +board_build.ldscript = boards/nrf52840_s140_v6_extrafs.ld +board_upload.maximum_size = 708608 +build_flags = ${ThinkNode_M3.build_flags} + -I examples/companion_radio/ui-orig + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D BLE_PIN_CODE=123456 + -D BLE_TX_POWER=0 + -D OFFLINE_QUEUE_SIZE=256 + -D DISPLAY_CLASS=NullDisplayDriver + -D PIN_BUZZER=23 + -D PIN_BUZZER_EN=36 +build_src_filter = ${ThinkNode_M3.build_src_filter} + + + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-orig/*.cpp> +lib_deps = ${ThinkNode_M3.lib_deps} + densaugeo/base64 @ ~1.4.0 + stevemarple/MicroNMEA @ ^2.0.6 + end2endzone/NonBlockingRTTTL@^1.3.0 + +[env:ThinkNode_M3_kiss_modem] +extends = ThinkNode_M3 +build_src_filter = ${ThinkNode_M3.build_src_filter} + +<../examples/kiss_modem/> +lib_deps = ${ThinkNode_M3.lib_deps} + stevemarple/MicroNMEA @ ^2.0.6 + +[LilyGo_T-Echo-Lite] +extends = nrf52_base +board = t-echo +board_build.ldscript = boards/nrf52840_s140_v6.ld +build_flags = ${nrf52_base.build_flags} + -I variants/lilygo_techo_lite + -I src/helpers/nrf52 + -I lib/nrf52/s140_nrf52_6.1.1_API/include + -I lib/nrf52/s140_nrf52_6.1.1_API/include/nrf52 + -D LILYGO_TECHO + -D RADIO_CLASS=CustomSX1262 + -D WRAPPER_CLASS=CustomSX1262Wrapper + -D LORA_TX_POWER=22 + -D SX126X_POWER_EN=30 + -D SX126X_DIO3_TCXO_VOLTAGE=3.0 + -D SX126X_CURRENT_LIMIT=140 + -D SX126X_RX_BOOSTED_GAIN=1 + -D P_LORA_TX_LED=LED_GREEN + -D DISABLE_DIAGNOSTIC_OUTPUT + -D ENV_INCLUDE_GPS=1 + -D GPS_BAUD_RATE=9600 + -D PIN_GPS_EN=GPS_EN + -D DISPLAY_CLASS=GxEPDDisplay + -D EINK_DISPLAY_MODEL=GxEPD2_122_T61 + -D EINK_SCALE_X=1.5f + -D EINK_SCALE_Y=2.0f + -D EINK_X_OFFSET=0 + -D EINK_Y_OFFSET=10 + -D DISPLAY_ROTATION=4 + -D AUTO_OFF_MILLIS=0 +build_src_filter = ${nrf52_base.build_src_filter} + + + + + + + + + + + +<../variants/lilygo_techo_lite> +lib_deps = + ${nrf52_base.lib_deps} + stevemarple/MicroNMEA @ ^2.0.6 + adafruit/Adafruit BME280 Library @ ^2.3.0 + https://github.com/SoulOfNoob/GxEPD2.git + bakercp/CRC32 @ ^2.0.0 +debug_tool = jlink +upload_protocol = nrfutil + +[env:LilyGo_T-Echo-Lite_repeater] +extends = LilyGo_T-Echo-Lite +build_src_filter = ${LilyGo_T-Echo-Lite.build_src_filter} + +<../examples/simple_repeater> +build_flags = + ${LilyGo_T-Echo-Lite.build_flags} + -D ADVERT_NAME='"T-Echo-Lite Repeater"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 + +[env:LilyGo_T-Echo-Lite_room_server] +extends = LilyGo_T-Echo-Lite +build_src_filter = ${LilyGo_T-Echo-Lite.build_src_filter} + +<../examples/simple_room_server> +build_flags = + ${LilyGo_T-Echo-Lite.build_flags} + -D ADVERT_NAME='"T-Echo-Lite Room"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + +[env:LilyGo_T-Echo-Lite_companion_radio_ble] +extends = LilyGo_T-Echo-Lite +board_build.ldscript = boards/nrf52840_s140_v6_extrafs.ld +board_upload.maximum_size = 712704 +build_flags = + ${LilyGo_T-Echo-Lite.build_flags} + -I src/helpers/ui + -I examples/companion_radio/ui-new + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D BLE_PIN_CODE=123456 + -D OFFLINE_QUEUE_SIZE=256 + -D UI_RECENT_LIST_SIZE=9 + -D UI_SENSORS_PAGE=1 + -D AUTO_SHUTDOWN_MILLIVOLTS=3300 +build_src_filter = ${LilyGo_T-Echo-Lite.build_src_filter} + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${LilyGo_T-Echo-Lite.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:LilyGo_T-Echo-Lite_kiss_modem] +extends = LilyGo_T-Echo-Lite +build_src_filter = ${LilyGo_T-Echo-Lite.build_src_filter} + +<../examples/kiss_modem/> + +[env:LilyGo_T-Echo-Lite_companion_radio_usb] +extends = LilyGo_T-Echo-Lite +board_build.ldscript = boards/nrf52840_s140_v6_extrafs.ld +board_upload.maximum_size = 712704 +build_flags = + ${LilyGo_T-Echo-Lite.build_flags} + -I src/helpers/ui + -I examples/companion_radio/ui-new + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D OFFLINE_QUEUE_SIZE=256 + -D UI_RECENT_LIST_SIZE=9 + -D UI_SENSORS_PAGE=1 + -D AUTO_SHUTDOWN_MILLIVOLTS=3300 +build_src_filter = ${LilyGo_T-Echo-Lite.build_src_filter} + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${LilyGo_T-Echo-Lite.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:LilyGo_T-Echo-Lite_non_shell_companion_radio_ble] +extends = LilyGo_T-Echo-Lite +upload_protocol = nrfutil +board_build.ldscript = boards/nrf52840_s140_v6_extrafs.ld +board_upload.maximum_size = 712704 +build_flags = + ${nrf52_base.build_flags} + -I variants/lilygo_techo_lite + -I src/helpers/nrf52 + -I lib/nrf52/s140_nrf52_6.1.1_API/include + -I lib/nrf52/s140_nrf52_6.1.1_API/include/nrf52 + -I src/helpers/ui + -I examples/companion_radio/ui-new + -D LILYGO_TECHO + -D RADIO_CLASS=CustomSX1262 + -D WRAPPER_CLASS=CustomSX1262Wrapper + -D LORA_TX_POWER=22 + -D SX126X_POWER_EN=30 + -D SX126X_DIO3_TCXO_VOLTAGE=3.0 + -D SX126X_CURRENT_LIMIT=140 + -D SX126X_RX_BOOSTED_GAIN=1 + -D P_LORA_TX_LED=LED_GREEN + -D DISABLE_DIAGNOSTIC_OUTPUT + -D ENV_INCLUDE_GPS=1 + -D GPS_BAUD_RATE=9600 + -D PIN_GPS_EN=GPS_EN + -D AUTO_OFF_MILLIS=0 + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D BLE_PIN_CODE=123456 + -D OFFLINE_QUEUE_SIZE=256 + -D UI_RECENT_LIST_SIZE=9 + -D AUTO_SHUTDOWN_MILLIVOLTS=3300 +build_src_filter = ${nrf52_base.build_src_filter} + + + + + + + + + +<../variants/lilygo_techo_lite> + + + +<../examples/companion_radio/*.cpp> +lib_deps = + ${LilyGo_T-Echo-Lite.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:LilyGo_T-Echo-Lite_non_shell_companion_radio_usb] +extends = LilyGo_T-Echo-Lite +upload_protocol = nrfutil +board_build.ldscript = boards/nrf52840_s140_v6_extrafs.ld +board_upload.maximum_size = 712704 +build_flags = + ${nrf52_base.build_flags} + -I variants/lilygo_techo_lite + -I src/helpers/nrf52 + -I lib/nrf52/s140_nrf52_6.1.1_API/include + -I lib/nrf52/s140_nrf52_6.1.1_API/include/nrf52 + -I src/helpers/ui + -I examples/companion_radio/ui-new + -D LILYGO_TECHO + -D RADIO_CLASS=CustomSX1262 + -D WRAPPER_CLASS=CustomSX1262Wrapper + -D LORA_TX_POWER=22 + -D SX126X_POWER_EN=30 + -D SX126X_DIO3_TCXO_VOLTAGE=3.0 + -D SX126X_CURRENT_LIMIT=140 + -D SX126X_RX_BOOSTED_GAIN=1 + -D P_LORA_TX_LED=LED_GREEN + -D DISABLE_DIAGNOSTIC_OUTPUT + -D ENV_INCLUDE_GPS=1 + -D GPS_BAUD_RATE=9600 + -D PIN_GPS_EN=GPS_EN + -D AUTO_OFF_MILLIS=0 + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D UI_RECENT_LIST_SIZE=9 + -D AUTO_SHUTDOWN_MILLIVOLTS=3300 + -D ENABLE_USB_INTERFACE +build_src_filter = ${nrf52_base.build_src_filter} + + + + + + + + + +<../variants/lilygo_techo_lite> + +<../examples/companion_radio/*.cpp> +lib_deps = + ${LilyGo_T-Echo-Lite.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[Heltec_T190_base] +extends = esp32_base +board = heltec_t190 +build_flags = + ${esp32_base.build_flags} + -I variants/heltec_t190 + -I src/helpers/ui + -D HELTEC_VISION_MASTER_T190 + -D USE_SX1262 + -D RADIO_CLASS=CustomSX1262 + -D WRAPPER_CLASS=CustomSX1262Wrapper + -D P_LORA_DIO_1=14 + -D P_LORA_NSS=8 + -D P_LORA_RESET=12 + -D P_LORA_BUSY=13 + -D P_LORA_SCLK=9 + -D P_LORA_MISO=11 + -D P_LORA_MOSI=10 + -D LORA_TX_POWER=22 + -D PIN_USER_BTN=0 + -D PIN_VEXT_EN=5 + -D PIN_VEXT_EN_ACTIVE=HIGH + -D PIN_VBAT_READ=6 + -D PIN_ADC_CTRL=46 + -D SX126X_DIO2_AS_RF_SWITCH=true + -D SX126X_DIO3_TCXO_VOLTAGE=1.8 + -D SX126X_CURRENT_LIMIT=140 + -D SX126X_RX_BOOSTED_GAIN=1 + -D PIN_BOARD_SDA=2 + -D PIN_BOARD_SCL=1 + -D PIN_TFT_SCL=38 + -D PIN_TFT_SDA=48 + -D PIN_TFT_RST=40 + -D PIN_TFT_VDD_CTL=7 + -D PIN_TFT_LEDA_CTL=17 + -D PIN_TFT_LEDA_CTL_ACTIVE=HIGH + -D PIN_TFT_CS=39 + -D PIN_TFT_DC=47 + -D ST7789 + -D DISPLAY_CLASS=ST7789Display +build_src_filter = ${esp32_base.build_src_filter} + +<../variants/heltec_t190> + + + + + + + + +lib_deps = + ${esp32_base.lib_deps} + adafruit/Adafruit GFX Library @ ^1.12.1 + +[env:Heltec_T190_companion_radio_ble_] +extends = Heltec_T190_base +build_flags = + ${Heltec_T190_base.build_flags} + -I examples/companion_radio/ui-new + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D BLE_PIN_CODE=123456 + -D BLE_DEBUG_LOGGING=1 + -D OFFLINE_QUEUE_SIZE=256 +build_src_filter = ${Heltec_T190_base.build_src_filter} + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${Heltec_T190_base.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:Heltec_T190_companion_radio_usb_] +extends = Heltec_T190_base +build_flags = + ${Heltec_T190_base.build_flags} + -I examples/companion_radio/ui-new + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D OFFLINE_QUEUE_SIZE=256 + -D ENABLE_USB_INTERFACE +build_src_filter = ${Heltec_T190_base.build_src_filter} + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${Heltec_T190_base.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:Heltec_T190_repeater_] +extends = Heltec_T190_base +build_flags = + ${Heltec_T190_base.build_flags} + -D ADVERT_NAME='"Heltec T190 Repeater"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 +build_src_filter = ${Heltec_T190_base.build_src_filter} + +<../examples/simple_repeater> +lib_deps = + ${Heltec_T190_base.lib_deps} + ${esp32_ota.lib_deps} + +[env:Heltec_T190_repeater_bridge_espnow_] +extends = Heltec_T190_base +build_flags = + ${Heltec_T190_base.build_flags} + -D ADVERT_NAME='"ESPNow Bridge"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 + -D WITH_ESPNOW_BRIDGE=1 +build_src_filter = ${Heltec_T190_base.build_src_filter} + + + +<../examples/simple_repeater> +lib_deps = + ${Heltec_T190_base.lib_deps} + ${esp32_ota.lib_deps} + +[env:Heltec_T190_room_server_] +extends = Heltec_T190_base +build_flags = + ${Heltec_T190_base.build_flags} + -D ADVERT_NAME='"Heltec T190 Room"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D ROOM_PASSWORD='"hello"' +build_src_filter = ${Heltec_T190_base.build_src_filter} + +<../examples/simple_room_server> +lib_deps = + ${Heltec_T190_base.lib_deps} + ${esp32_ota.lib_deps} + +[env:Heltec_T190_kiss_modem] +extends = Heltec_T190_base +build_src_filter = ${Heltec_T190_base.build_src_filter} + +<../examples/kiss_modem/> + +[GAT562_30S_Mesh_Kit] +extends = nrf52_base +board = rak4631 +board_check = true +build_flags = ${nrf52_base.build_flags} + ${sensor_base.build_flags} + -I variants/gat562_30s_mesh_kit + -D RAK_4631 + -D RAK_BOARD + -D PIN_BOARD_SCL=14 + -D PIN_BOARD_SDA=13 + -D PIN_OLED_RESET=-1 + -D UI_HAS_JOYSTICK=1 + -D RADIO_CLASS=CustomSX1262 + -D WRAPPER_CLASS=CustomSX1262Wrapper + -D LORA_TX_POWER=22 + -D SX126X_CURRENT_LIMIT=140 + -D PIN_BUZZER=33 + -D SX126X_RX_BOOSTED_GAIN=1 + -D SX126X_DIO2_AS_RF_SWITCH=true +build_src_filter = ${nrf52_base.build_src_filter} + +<../variants/gat562_30s_mesh_kit> + + + + + + +lib_deps = + ${nrf52_base.lib_deps} + ${sensor_base.lib_deps} + adafruit/Adafruit SSD1306 @ ^2.5.13 + sparkfun/SparkFun u-blox GNSS Arduino Library@^2.2.27 + +[env:GAT562_30S_Mesh_Kit_repeater] +extends = GAT562_30S_Mesh_Kit +build_flags = + ${GAT562_30S_Mesh_Kit.build_flags} + -D DISPLAY_CLASS=SSD1306Display + -D ADVERT_NAME='"GAT562 Repeater"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 +build_src_filter = ${GAT562_30S_Mesh_Kit.build_src_filter} + + + +<../examples/simple_repeater> + +[env:GAT562_30S_Mesh_Kit_room_server] +extends = GAT562_30S_Mesh_Kit +build_flags = + ${GAT562_30S_Mesh_Kit.build_flags} + -D DISPLAY_CLASS=SSD1306Display + -D ADVERT_NAME='"GAT562 Room"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D ROOM_PASSWORD='"hello"' +build_src_filter = ${GAT562_30S_Mesh_Kit.build_src_filter} + + + +<../examples/simple_room_server> + +[env:GAT562_30S_Mesh_Kit_companion_radio_usb] +extends = GAT562_30S_Mesh_Kit +board_build.ldscript = boards/nrf52840_s140_v6_extrafs.ld +board_upload.maximum_size = 712704 +build_flags = + ${GAT562_30S_Mesh_Kit.build_flags} + -I examples/companion_radio/ui-new + -D DISPLAY_CLASS=SSD1306Display + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D ENABLE_USB_INTERFACE +build_src_filter = ${GAT562_30S_Mesh_Kit.build_src_filter} + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> + + +lib_deps = + ${GAT562_30S_Mesh_Kit.lib_deps} + densaugeo/base64 @ ~1.4.0 + end2endzone/NonBlockingRTTTL@^1.3.0 + +[env:GAT562_30S_Mesh_Kit_companion_radio_ble] +extends = GAT562_30S_Mesh_Kit +board_build.ldscript = boards/nrf52840_s140_v6_extrafs.ld +board_upload.maximum_size = 712704 +build_flags = + ${GAT562_30S_Mesh_Kit.build_flags} + -I examples/companion_radio/ui-new + -D DISPLAY_CLASS=SSD1306Display + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D BLE_PIN_CODE=123456 + -D BLE_DEBUG_LOGGING=1 + -D OFFLINE_QUEUE_SIZE=256 +build_src_filter = ${GAT562_30S_Mesh_Kit.build_src_filter} + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${GAT562_30S_Mesh_Kit.lib_deps} + densaugeo/base64 @ ~1.4.0 + end2endzone/NonBlockingRTTTL@^1.3.0 + +[env:GAT562_30S_Mesh_Kit_kiss_modem] +extends = GAT562_30S_Mesh_Kit +build_src_filter = ${GAT562_30S_Mesh_Kit.build_src_filter} + +<../examples/kiss_modem/> + +[SenseCap_Solar] +extends = nrf52_base +board = seeed_sensecap_solar +board_build.ldscript = boards/nrf52840_s140_v7.ld +build_flags = ${nrf52_base.build_flags} + ${sensor_base.build_flags} + -I lib/nrf52/s140_nrf52_7.3.0_API/include + -I lib/nrf52/s140_nrf52_7.3.0_API/include/nrf52 + -I variants/sensecap_solar + -I src/helpers/nrf52 + -D NRF52_PLATFORM=1 + -D USE_SX1262 + -D RADIO_CLASS=CustomSX1262 + -D WRAPPER_CLASS=CustomSX1262Wrapper + -D P_LORA_TX_LED=12 + -D P_LORA_DIO_1=1 + -D P_LORA_RESET=2 + -D P_LORA_BUSY=3 + -D P_LORA_NSS=4 + -D PIN_USER_BTN=PIN_BUTTON1 + -D LORA_TX_POWER=22 + -D SX126X_RXEN=5 + -D SX126X_TXEN=RADIOLIB_NC + -D SX126X_DIO2_AS_RF_SWITCH=1 + -D SX126X_DIO3_TCXO_VOLTAGE=1.8 + -D SX126X_CURRENT_LIMIT=140 + -D SX126X_RX_BOOSTED_GAIN=1 + -D ENV_INCLUDE_GPS=1 +build_src_filter = ${nrf52_base.build_src_filter} + + + + + +<../variants/sensecap_solar> +debug_tool = jlink +upload_protocol = nrfutil +lib_deps = + ${nrf52_base.lib_deps} + ${sensor_base.lib_deps} + +[env:SenseCap_Solar_repeater] +extends = SenseCap_Solar +build_flags = + ${SenseCap_Solar.build_flags} + -D ADVERT_NAME='"SenseCap_Solar Repeater"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 +build_src_filter = ${SenseCap_Solar.build_src_filter} + +<../examples/simple_repeater/*.cpp> + +[env:SenseCap_Solar_room_server] +extends = SenseCap_Solar +build_flags = + ${SenseCap_Solar.build_flags} + -D ADVERT_NAME='"SenseCap_Solar Room"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' +build_src_filter = ${SenseCap_Solar.build_src_filter} + +<../examples/simple_room_server/*.cpp> + +[env:SenseCap_Solar_companion_radio_ble] +extends = SenseCap_Solar +board_build.ldscript = boards/nrf52840_s140_v7_extrafs.ld +board_upload.maximum_size = 708608 +build_flags = + ${SenseCap_Solar.build_flags} + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D BLE_PIN_CODE=123456 + -D OFFLINE_QUEUE_SIZE=256 +build_src_filter = ${SenseCap_Solar.build_src_filter} + + + +<../examples/companion_radio/*.cpp> +lib_deps = + ${SenseCap_Solar.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:SenseCap_Solar_companion_radio_usb] +extends = SenseCap_Solar +board_build.ldscript = boards/nrf52840_s140_v7_extrafs.ld +board_upload.maximum_size = 708608 +build_flags = + ${SenseCap_Solar.build_flags} + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D ENABLE_USB_INTERFACE +build_src_filter = ${SenseCap_Solar.build_src_filter} + + + +<../examples/companion_radio/*.cpp> +lib_deps = + ${SenseCap_Solar.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:SenseCap_Solar_kiss_modem] +extends = SenseCap_Solar +build_src_filter = ${SenseCap_Solar.build_src_filter} + +<../examples/kiss_modem/> + +[Tenstar_esp32_C3] +extends = esp32_base +board = esp32-c3-devkitm-1 +build_flags = + ${esp32_base.build_flags} + -I variants/tenstar_c3 + -D ESP32_CPU_FREQ=80 + -D LORA_TX_BOOST_PIN=4 + -D P_LORA_TX_NEOPIXEL_LED=10 + -D PIN_VBAT_READ=1 + -D P_LORA_MISO=9 + -D P_LORA_SCLK=8 + -D P_LORA_MOSI=7 + -D P_LORA_DIO_1=2 + -D P_LORA_NSS=6 + -D P_LORA_RESET=RADIOLIB_NC + -D P_LORA_BUSY=3 + -D SX126X_DIO2_AS_RF_SWITCH=true + -D SX126X_DIO3_TCXO_VOLTAGE=1.8 + -D SX126X_CURRENT_LIMIT=140 +build_src_filter = ${esp32_base.build_src_filter} + +<../variants/tenstar_c3> + +[env:Tenstar_C3_sx1262_repeater] +extends = Tenstar_esp32_C3 +build_src_filter = ${Tenstar_esp32_C3.build_src_filter} + +<../examples/simple_repeater/*.cpp> +build_flags = + ${Tenstar_esp32_C3.build_flags} + -D RADIO_CLASS=CustomSX1262 + -D WRAPPER_CLASS=CustomSX1262Wrapper + -D SX126X_RX_BOOSTED_GAIN=1 + -D LORA_TX_POWER=22 + -D ADVERT_NAME='"Tenstar C3 Repeater"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 +lib_deps = + ${Tenstar_esp32_C3.lib_deps} + ${esp32_ota.lib_deps} + +[env:Tenstar_C3_sx1262_repeater_bridge_espnow] +extends = Tenstar_esp32_C3 +build_src_filter = ${Tenstar_esp32_C3.build_src_filter} + + + +<../examples/simple_repeater/*.cpp> +build_flags = + ${Tenstar_esp32_C3.build_flags} + -D RADIO_CLASS=CustomSX1262 + -D WRAPPER_CLASS=CustomSX1262Wrapper + -D SX126X_RX_BOOSTED_GAIN=1 + -D LORA_TX_POWER=22 + -D ADVERT_NAME='"ESPNow Bridge"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 + -D WITH_ESPNOW_BRIDGE=1 +lib_deps = + ${Tenstar_esp32_C3.lib_deps} + ${esp32_ota.lib_deps} + +[env:Tenstar_C3_sx1268_repeater] +extends = Tenstar_esp32_C3 +build_src_filter = ${Tenstar_esp32_C3.build_src_filter} + +<../examples/simple_repeater/*.cpp> +build_flags = + ${Tenstar_esp32_C3.build_flags} + -D RADIO_CLASS=CustomSX1268 + -D WRAPPER_CLASS=CustomSX1268Wrapper + -D LORA_TX_POWER=22 + -D ADVERT_NAME='"Tenstar C3 Repeater"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 +lib_deps = + ${Tenstar_esp32_C3.lib_deps} + ${esp32_ota.lib_deps} + +[env:Tenstar_C3_sx1268_repeater_bridge_espnow] +extends = Tenstar_esp32_C3 +build_src_filter = ${Tenstar_esp32_C3.build_src_filter} + + + +<../examples/simple_repeater/*.cpp> +build_flags = + ${Tenstar_esp32_C3.build_flags} + -D RADIO_CLASS=CustomSX1268 + -D WRAPPER_CLASS=CustomSX1268Wrapper + -D LORA_TX_POWER=22 + -D ADVERT_NAME='"ESPNow Bridge"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 + -D WITH_ESPNOW_BRIDGE=1 +lib_deps = + ${Tenstar_esp32_C3.lib_deps} + ${esp32_ota.lib_deps} + +[env:Tenstar_C3_sx1262_kiss_modem] +extends = Tenstar_esp32_C3 +build_src_filter = ${Tenstar_esp32_C3.build_src_filter} + +<../examples/kiss_modem/> +build_flags = + ${Tenstar_esp32_C3.build_flags} + -D RADIO_CLASS=CustomSX1262 + -D WRAPPER_CLASS=CustomSX1262Wrapper + -D LORA_TX_POWER=22 + +[env:Tenstar_C3_sx1268_kiss_modem] +extends = Tenstar_esp32_C3 +build_src_filter = ${Tenstar_esp32_C3.build_src_filter} + +<../examples/kiss_modem/> +build_flags = + ${Tenstar_esp32_C3.build_flags} + -D RADIO_CLASS=CustomSX1268 + -D WRAPPER_CLASS=CustomSX1268Wrapper + -D LORA_TX_POWER=22 + +[Heltec_ct62] +extends = esp32_base +board = esp32-c3-devkitm-1 +board_build.partitions = min_spiffs.csv +build_flags = + ${esp32_base.build_flags} + -I variants/heltec_ct62 + -D HELTEC_HT_CT62=1 + -D USE_SX1262 + -D RADIO_CLASS=CustomSX1262 + -D WRAPPER_CLASS=CustomSX1262Wrapper + -D ESP32_CPU_FREQ=80 + -D LORA_TX_POWER=22 + -D P_LORA_TX_LED=18 + -D PIN_BOARD_SDA=0 + -D PIN_BOARD_SCL=1 + -D PIN_VBAT_READ=2 + -D P_LORA_DIO_1=3 + -D P_LORA_NSS=8 + -D P_LORA_RESET=5 + -D P_LORA_DIO_0=RADIOLIB_NC + -D P_LORA_DIO_2=RADIOLIB_NC + -D P_LORA_BUSY=4 + -D P_LORA_SCLK=10 + -D P_LORA_MISO=6 + -D P_LORA_MOSI=7 + -D SX126X_DIO2_AS_RF_SWITCH=true + -D SX126X_DIO3_TCXO_VOLTAGE=1.8 + -D SX126X_CURRENT_LIMIT=140 + -D SX126X_RX_BOOSTED_GAIN=1 +build_src_filter = ${esp32_base.build_src_filter} + +<../variants/heltec_ct62> + +[env:Heltec_ct62_repeater] +extends = Heltec_ct62 +build_flags = + ${Heltec_ct62.build_flags} + -D ADVERT_NAME='"HT-CT62 Repeater"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 +build_src_filter = ${Heltec_ct62.build_src_filter} + +<../examples/simple_repeater> +lib_deps = + ${Heltec_ct62.lib_deps} + ${esp32_ota.lib_deps} + +[env:Heltec_ct62_repeater_bridge_espnow] +extends = Heltec_ct62 +build_flags = + ${Heltec_ct62.build_flags} + -D ADVERT_NAME='"ESPNow Bridge"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 + -D WITH_ESPNOW_BRIDGE=1 +build_src_filter = ${Heltec_ct62.build_src_filter} + + + +<../examples/simple_repeater> +lib_deps = + ${Heltec_ct62.lib_deps} + ${esp32_ota.lib_deps} + +[env:Heltec_ct62_companion_radio_usb] +extends = Heltec_ct62 +build_flags = + ${Heltec_ct62.build_flags} + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D OFFLINE_QUEUE_SIZE=256 + -D ENABLE_USB_INTERFACE +build_src_filter = ${Heltec_ct62.build_src_filter} + +<../examples/companion_radio/*.cpp> +lib_deps = + ${Heltec_ct62.lib_deps} + ${esp32_ota.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:Heltec_ct62_companion_radio_ble] +extends = Heltec_ct62 +build_flags = + ${Heltec_ct62.build_flags} + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D OFFLINE_QUEUE_SIZE=256 + -D BLE_PIN_CODE=123456 +build_src_filter = ${Heltec_ct62.build_src_filter} + +<../examples/companion_radio/*.cpp> + + +lib_deps = + ${Heltec_ct62.lib_deps} + ${esp32_ota.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:Heltec_ct62_sensor] +extends = Heltec_ct62 +build_flags = + ${Heltec_ct62.build_flags} + -D ADVERT_NAME='"HT-CT62 Sensor"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D PIN_BOARD_SDA=-1 + -D PIN_BOARD_SCL=-1 + -D PIN_BOARD_RELAY_CH1=0 + -D PIN_BOARD_RELAY_CH2=1 + -D PIN_BOARD_DIGITAL_IN=19 +build_src_filter = ${Heltec_ct62.build_src_filter} + +<../examples/simple_sensor> +lib_deps = + ${Heltec_ct62.lib_deps} + ${esp32_ota.lib_deps} + +[env:Heltec_ct62_kiss_modem] +extends = Heltec_ct62 +build_src_filter = ${Heltec_ct62.build_src_filter} + +<../examples/kiss_modem/> + +[muzi_base_common] +extends = nrf52_base +board = muzi_base +board_build.ldscript = boards/nrf52840_s140_v6.ld +build_flags = ${nrf52_base.build_flags} + -I src/helpers/nrf52 + -I lib/nrf52/s140_nrf52_6.1.1_API/include + -I lib/nrf52/s140_nrf52_6.1.1_API/include/nrf52 + -I variants/muzi_base + -I src/helpers/ui + -D MUZI_BASE + -D NRF52_POWER_MANAGEMENT + -D PIN_USER_BTN=PIN_BUTTON1 + -D USER_BTN_PRESSED=LOW + -D PIN_STATUS_LED=35 + -D LORA_TX_POWER=22 + -D P_LORA_BUSY=LORA_BUSY + -D P_LORA_SCLK=LORA_SCLK + -D P_LORA_NSS=LORA_NSS + -D P_LORA_DIO_1=LORA_DIO_1 + -D P_LORA_MISO=LORA_MISO + -D P_LORA_MOSI=LORA_MOSI + -D P_LORA_RESET=LORA_RESET + -D QSPIFLASH=1 +build_src_filter = ${nrf52_base.build_src_filter} + + + + + +<../variants/muzi_base> +debug_tool = jlink +upload_protocol = nrfutil +lib_deps = + ${nrf52_base.lib_deps} + ${sensor_base.lib_deps} + +[muzi_base_duo] +extends = muzi_base_common +build_flags = ${muzi_base_common.build_flags} + -D USE_LR1121 + -D RADIO_CLASS=CustomLR1121 + -D WRAPPER_CLASS=CustomLR1121Wrapper + -D RF_SWITCH_TABLE + -D RX_BOOSTED_GAIN=true + -D LR11X0_DIO_AS_RF_SWITCH=true + -D LR11X0_DIO3_TCXO_VOLTAGE=3.0 + +[muzi_base_uno] +extends = muzi_base_common +build_flags = ${muzi_base_common.build_flags} + -D USE_SX1262 + -D RADIO_CLASS=CustomSX1262 + -D WRAPPER_CLASS=CustomSX1262Wrapper + -D SX126X_RX_BOOSTED_GAIN=1 + -D SX126X_CURRENT_LIMIT=140 + -D SX126X_DIO2_AS_RF_SWITCH=1 + -D SX126X_DIO3_TCXO_VOLTAGE=3.3 + +[env:muzi_base_duo_repeater] +extends = muzi_base_duo +build_flags = ${muzi_base_duo.build_flags} + -I examples/companion_radio/ui-new + -D ADVERT_NAME='"Muzi Base Repeater"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 +build_src_filter = ${muzi_base_duo.build_src_filter} + +<../examples/simple_repeater> +lib_deps = ${muzi_base_duo.lib_deps} + +[env:muzi_base_duo_room_server] +extends = muzi_base_duo +build_flags = ${muzi_base_duo.build_flags} + -I examples/companion_radio/ui-new + -D ADVERT_NAME='"Muzi Base Room"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D ROOM_PASSWORD='"hello"' +build_src_filter = ${muzi_base_duo.build_src_filter} + +<../examples/simple_room_server> +lib_deps = ${muzi_base_duo.lib_deps} + +[env:muzi_base_duo_companion_radio_usb] +extends = muzi_base_duo +board_build.ldscript = boards/nrf52840_s140_v6_extrafs.ld +board_upload.maximum_size = 708608 +build_flags = ${muzi_base_duo.build_flags} + -I examples/companion_radio/ui-new + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D OFFLINE_QUEUE_SIZE=256 + -D DISPLAY_CLASS=NullDisplayDriver +build_src_filter = ${muzi_base_duo.build_src_filter} + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = ${muzi_base_duo.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:muzi_base_duo_companion_radio_ble] +extends = muzi_base_duo +board_build.ldscript = boards/nrf52840_s140_v6_extrafs.ld +board_upload.maximum_size = 708608 +build_flags = ${muzi_base_duo.build_flags} + -I examples/companion_radio/ui-new + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D BLE_PIN_CODE=123456 + -D QSPIFLASH=1 + -D OFFLINE_QUEUE_SIZE=256 + -D DISPLAY_CLASS=NullDisplayDriver +build_src_filter = ${muzi_base_duo.build_src_filter} + + + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = ${muzi_base_duo.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[muzi_base_duo_superIO] +extends = muzi_base_duo +board_build.ldscript = boards/nrf52840_s140_v6_extrafs.ld +board_upload.maximum_size = 708608 +build_flags = ${muzi_base_duo.build_flags} + -D MUZI_BASE_SUPERIO + -D UI_HAS_JOYSTICK=1 + -D OFFLINE_QUEUE_SIZE=256 + -D DISPLAY_CLASS=SH1107Display + -D DISPLAY_ROTATION=2 + -D ENV_INCLUDE_GPS=1 + -D ENV_SKIP_GPS_DETECT + -D PIN_BUZZER=22 +build_src_filter = ${muzi_base_duo.build_src_filter} + + + + + + + + + + +lib_deps = ${muzi_base_duo.lib_deps} + densaugeo/base64 @ ~1.4.0 + stevemarple/MicroNMEA @ ^2.0.6 + end2endzone/NonBlockingRTTTL@^1.3.0 + adafruit/Adafruit SH110X@^2.1.14 + artronshop/ArtronShop_RX8130CE@1.0.0 + adafruit/Adafruit GFX Library @ ^1.12.1 +debug_tool = jlink +upload_protocol = nrfutil + +[env:muzi_base_duo_superIO_companion_radio_ble] +extends = muzi_base_duo_superIO +board_build.ldscript = boards/nrf52840_s140_v6_extrafs.ld +board_upload.maximum_size = 708608 +build_flags = ${muzi_base_duo_superIO.build_flags} + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -I examples/companion_radio/ui-new + -D BLE_PIN_CODE=123456 + -D QSPIFLASH=1 + -D OFFLINE_QUEUE_SIZE=256 +build_src_filter = ${muzi_base_duo_superIO.build_src_filter} + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${muzi_base_duo_superIO.lib_deps} + +[env:muzi_base_uno_repeater] +extends = muzi_base_uno +build_flags = ${muzi_base_uno.build_flags} + -I examples/companion_radio/ui-new + -D ADVERT_NAME='"Muzi Base Repeater"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 +build_src_filter = ${muzi_base_uno.build_src_filter} + +<../examples/simple_repeater> +lib_deps = ${muzi_base_uno.lib_deps} + +[env:muzi_base_uno_room_server] +extends = muzi_base_uno +build_flags = ${muzi_base_uno.build_flags} + -I examples/companion_radio/ui-new + -D ADVERT_NAME='"Muzi Base Room"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D ROOM_PASSWORD='"hello"' +build_src_filter = ${muzi_base_uno.build_src_filter} + +<../examples/simple_room_server> +lib_deps = ${muzi_base_uno.lib_deps} + +[env:muzi_base_uno_companion_radio_usb] +extends = muzi_base_uno +board_build.ldscript = boards/nrf52840_s140_v6_extrafs.ld +board_upload.maximum_size = 708608 +build_flags = ${muzi_base_uno.build_flags} + -I examples/companion_radio/ui-new + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D OFFLINE_QUEUE_SIZE=256 + -D DISPLAY_CLASS=NullDisplayDriver +build_src_filter = ${muzi_base_uno.build_src_filter} + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = ${muzi_base_uno.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:muzi_base_uno_companion_radio_ble] +extends = muzi_base_uno +board_build.ldscript = boards/nrf52840_s140_v6_extrafs.ld +board_upload.maximum_size = 708608 +build_flags = ${muzi_base_uno.build_flags} + -I examples/companion_radio/ui-new + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D BLE_PIN_CODE=123456 + -D QSPIFLASH=1 + -D OFFLINE_QUEUE_SIZE=256 + -D DISPLAY_CLASS=NullDisplayDriver +build_src_filter = ${muzi_base_uno.build_src_filter} + + + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = ${muzi_base_uno.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[muzi_base_uno_superIO] +extends = muzi_base_uno +board_build.ldscript = boards/nrf52840_s140_v6_extrafs.ld +board_upload.maximum_size = 708608 +build_flags = ${muzi_base_uno.build_flags} + -D MUZI_BASE_SUPERIO + -D UI_HAS_JOYSTICK=1 + -D OFFLINE_QUEUE_SIZE=256 + -D DISPLAY_CLASS=SH1107Display + -D DISPLAY_ROTATION=2 + -D ENV_INCLUDE_GPS=1 + -D ENV_SKIP_GPS_DETECT + -D PIN_BUZZER=22 +build_src_filter = ${muzi_base_uno.build_src_filter} + + + + + + + + + + +lib_deps = ${muzi_base_uno.lib_deps} + densaugeo/base64 @ ~1.4.0 + stevemarple/MicroNMEA @ ^2.0.6 + end2endzone/NonBlockingRTTTL@^1.3.0 + adafruit/Adafruit SH110X@^2.1.14 + artronshop/ArtronShop_RX8130CE@1.0.0 + adafruit/Adafruit GFX Library @ ^1.12.1 +debug_tool = jlink +upload_protocol = nrfutil + +[env:muzi_base_uno_superIO_companion_radio_ble] +extends = muzi_base_uno_superIO +board_build.ldscript = boards/nrf52840_s140_v6_extrafs.ld +board_upload.maximum_size = 708608 +build_flags = ${muzi_base_uno_superIO.build_flags} + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -I examples/companion_radio/ui-new + -D BLE_PIN_CODE=123456 + -D QSPIFLASH=1 + -D OFFLINE_QUEUE_SIZE=256 +build_src_filter = ${muzi_base_uno_superIO.build_src_filter} + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${muzi_base_uno_superIO.lib_deps} + +[Xiao_S3] +extends = esp32_base +board = seeed_xiao_esp32s3 +board_check = true +board_build.mcu = esp32s3 +build_flags = ${esp32_base.build_flags} + ${sensor_base.build_flags} + -I variants/xiao_s3 + -UENV_INCLUDE_GPS + -D SEEED_XIAO_S3 + -D PIN_VBAT_READ=1 + -D P_LORA_DIO_1=2 + -D P_LORA_NSS=5 + -D P_LORA_RESET=3 + -D P_LORA_BUSY=4 + -D P_LORA_SCLK=7 + -D P_LORA_MISO=8 + -D P_LORA_MOSI=9 + -D PIN_USER_BTN=-1 + -D PIN_STATUS_LED=21 + -D PIN_BOARD_SDA=D6 + -D PIN_BOARD_SCL=D7 + -D SX126X_RXEN=6 + -D SX126X_TXEN=RADIOLIB_NC + -D SX126X_DIO2_AS_RF_SWITCH=true + -D SX126X_DIO3_TCXO_VOLTAGE=1.8 + -D SX126X_CURRENT_LIMIT=140 + -D RADIO_CLASS=CustomSX1262 + -D WRAPPER_CLASS=CustomSX1262Wrapper + -D LORA_TX_POWER=22 + -D SX126X_RX_BOOSTED_GAIN=1 +build_src_filter = ${esp32_base.build_src_filter} + +<../variants/xiao_s3> + + +lib_deps = + ${esp32_base.lib_deps} + ${sensor_base.lib_deps} + +[env:Xiao_S3_repeater] +extends = Xiao_S3 +build_src_filter = ${Xiao_S3.build_src_filter} + +<../examples/simple_repeater/*.cpp> +build_flags = + ${Xiao_S3.build_flags} + -D ADVERT_NAME='"Xiao S3 Repeater"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 +lib_deps = + ${Xiao_S3.lib_deps} + ${esp32_ota.lib_deps} + +[env:Xiao_S3_repeater_bridge_espnow] +extends = Xiao_S3 +build_src_filter = ${Xiao_S3.build_src_filter} + + + +<../examples/simple_repeater/*.cpp> +build_flags = + ${Xiao_S3.build_flags} + -D ADVERT_NAME='"ESPNow Bridge"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 + -D WITH_ESPNOW_BRIDGE=1 +lib_deps = + ${Xiao_S3.lib_deps} + ${esp32_ota.lib_deps} + +[env:Xiao_S3_room_server] +extends = Xiao_S3 +build_src_filter = ${Xiao_S3.build_src_filter} + +<../examples/simple_room_server> +build_flags = + ${Xiao_S3.build_flags} + -D ADVERT_NAME='"Xiao S3 Room"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D ROOM_PASSWORD='"hello"' +lib_deps = + ${Xiao_S3.lib_deps} + ${esp32_ota.lib_deps} + +[env:Xiao_S3_companion_radio_ble] +extends = Xiao_S3 +build_flags = + ${Xiao_S3.build_flags} + -I examples/companion_radio/ui-new + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D BLE_PIN_CODE=123456 + -D DISPLAY_CLASS=SSD1306Display + -D OFFLINE_QUEUE_SIZE=256 + -D ENABLE_WIFI_INTERFACE +build_src_filter = ${Xiao_S3.build_src_filter} + + + + + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${Xiao_S3.lib_deps} + densaugeo/base64 @ ~1.4.0 + adafruit/Adafruit SSD1306 @ ^2.5.13 + +[env:Xiao_S3_companion_radio_usb] +extends = Xiao_S3 +build_flags = + ${Xiao_S3.build_flags} + -I examples/companion_radio/ui-new + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D DISPLAY_CLASS=SSD1306Display + -D OFFLINE_QUEUE_SIZE=256 + -D ENABLE_USB_INTERFACE +build_src_filter = ${Xiao_S3.build_src_filter} + + + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${Xiao_S3.lib_deps} + densaugeo/base64 @ ~1.4.0 + adafruit/Adafruit SSD1306 @ ^2.5.13 + +[env:Xiao_S3_sensor] +extends = Xiao_S3 +build_src_filter = ${Xiao_S3.build_src_filter} + +<../examples/simple_sensor> +build_flags = + ${Xiao_S3.build_flags} + -D ADVERT_NAME='"Xiao S3 Sensor"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' +lib_deps = + ${Xiao_S3.lib_deps} + ${esp32_ota.lib_deps} + +[env:Xiao_S3_kiss_modem] +extends = Xiao_S3 +build_src_filter = ${Xiao_S3.build_src_filter} + +<../examples/kiss_modem/> + +[Xiao_S3_WIO] +extends = esp32_base +board = seeed_xiao_esp32s3 +board_check = true +board_build.mcu = esp32s3 +build_flags = ${esp32_base.build_flags} + ${sensor_base.build_flags} + -I variants/xiao_s3_wio + -UENV_INCLUDE_GPS + -D SEEED_XIAO_S3 + -D P_LORA_DIO_1=39 + -D P_LORA_NSS=41 + -D P_LORA_RESET=42 + -D P_LORA_BUSY=40 + -D P_LORA_SCLK=7 + -D P_LORA_MISO=8 + -D P_LORA_MOSI=9 + -D PIN_USER_BTN=21 + -D PIN_STATUS_LED=48 + -D PIN_BOARD_SDA=D4 + -D PIN_BOARD_SCL=D5 + -D SX126X_RXEN=38 + -D SX126X_TXEN=RADIOLIB_NC + -D SX126X_DIO2_AS_RF_SWITCH=true + -D SX126X_DIO3_TCXO_VOLTAGE=1.8 + -D SX126X_CURRENT_LIMIT=140 + -D USE_SX1262 + -D RADIO_CLASS=CustomSX1262 + -D WRAPPER_CLASS=CustomSX1262Wrapper + -D LORA_TX_POWER=22 + -D SX126X_RX_BOOSTED_GAIN=1 +build_src_filter = ${esp32_base.build_src_filter} + +<../variants/xiao_s3_wio> + + +lib_deps = + ${esp32_base.lib_deps} + ${sensor_base.lib_deps} + +[env:Xiao_S3_WIO_repeater] +extends = Xiao_S3_WIO +build_src_filter = ${Xiao_S3_WIO.build_src_filter} + +<../examples/simple_repeater/*.cpp> +build_flags = + ${Xiao_S3_WIO.build_flags} + -D ADVERT_NAME='"XiaoS3 Repeater"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 +lib_deps = + ${Xiao_S3_WIO.lib_deps} + ${esp32_ota.lib_deps} + +[env:Xiao_S3_WIO_repeater_bridge_espnow] +extends = Xiao_S3_WIO +build_src_filter = ${Xiao_S3_WIO.build_src_filter} + + + +<../examples/simple_repeater/*.cpp> +build_flags = + ${Xiao_S3_WIO.build_flags} + -D ADVERT_NAME='"ESPNow Bridge"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 + -D WITH_ESPNOW_BRIDGE=1 +lib_deps = + ${Xiao_S3_WIO.lib_deps} + ${esp32_ota.lib_deps} + +[env:Xiao_S3_WIO_room_server] +extends = Xiao_S3_WIO +build_src_filter = ${Xiao_S3_WIO.build_src_filter} + +<../examples/simple_room_server> +build_flags = + ${Xiao_S3_WIO.build_flags} + -D ADVERT_NAME='"XiaoS3 Room"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D ROOM_PASSWORD='"hello"' +lib_deps = + ${Xiao_S3_WIO.lib_deps} + ${esp32_ota.lib_deps} + +[env:Xiao_S3_WIO_terminal_chat] +extends = Xiao_S3_WIO +build_flags = + ${Xiao_S3_WIO.build_flags} + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 +build_src_filter = ${Xiao_S3_WIO.build_src_filter} + +<../examples/simple_secure_chat/main.cpp> +lib_deps = + ${Xiao_S3_WIO.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:Xiao_S3_WIO_companion_radio_usb] +extends = Xiao_S3_WIO +build_flags = + ${Xiao_S3_WIO.build_flags} + -I examples/companion_radio/ui-new + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D DISPLAY_CLASS=SSD1306Display + -D OFFLINE_QUEUE_SIZE=256 + -D ENABLE_USB_INTERFACE +build_src_filter = ${Xiao_S3_WIO.build_src_filter} + + + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${Xiao_S3_WIO.lib_deps} + densaugeo/base64 @ ~1.4.0 + adafruit/Adafruit SSD1306 @ ^2.5.13 + +[env:Xiao_S3_WIO_companion_radio_ble] +extends = Xiao_S3_WIO +build_flags = + ${Xiao_S3_WIO.build_flags} + -I examples/companion_radio/ui-new + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D BLE_PIN_CODE=123456 + -D DISPLAY_CLASS=SSD1306Display + -D OFFLINE_QUEUE_SIZE=256 + -D ENABLE_WIFI_INTERFACE +build_src_filter = ${Xiao_S3_WIO.build_src_filter} + + + + + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${Xiao_S3_WIO.lib_deps} + densaugeo/base64 @ ~1.4.0 + adafruit/Adafruit SSD1306 @ ^2.5.13 + +[env:Xiao_S3_WIO_companion_radio_serial] +extends = Xiao_S3_WIO +build_flags = + ${Xiao_S3_WIO.build_flags} + -I examples/companion_radio/ui-new + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D DISPLAY_CLASS=SSD1306Display + -D SERIAL_TX=D6 + -D SERIAL_RX=D7 +build_src_filter = ${Xiao_S3_WIO.build_src_filter} + + + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${Xiao_S3_WIO.lib_deps} + densaugeo/base64 @ ~1.4.0 + adafruit/Adafruit SSD1306 @ ^2.5.13 + +[env:Xiao_S3_WIO_companion_radio_wifi] +extends = Xiao_S3_WIO +build_src_filter = ${Xiao_S3_WIO.build_src_filter} + + + + + + + + + +<../examples/companion_radio/*.cpp> +build_flags = + ${Xiao_S3_WIO.build_flags} + -I examples/companion_radio/ui-new + -D ENABLE_WIFI_INTERFACE + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D OFFLINE_QUEUE_SIZE=256 + -D WIFI_DEBUG_LOGGING=1 + -D WIFI_SSID='"myssid"' + -D WIFI_PWD='"password"' +lib_deps = + ${Xiao_S3_WIO.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:Xiao_S3_WIO_sensor] +extends = Xiao_S3_WIO +build_src_filter = ${Xiao_S3_WIO.build_src_filter} + +<../examples/simple_sensor> +build_flags = + ${Xiao_S3_WIO.build_flags} + -D ADVERT_NAME='"XiaoS3 sensor"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' +lib_deps = + ${Xiao_S3_WIO.lib_deps} + ${esp32_ota.lib_deps} + +[env:Xiao_S3_WIO_kiss_modem] +extends = Xiao_S3_WIO +build_src_filter = ${Xiao_S3_WIO.build_src_filter} + +<../examples/kiss_modem/> + +[Generic_E22] +extends = esp32_base +board = esp32doit-devkit-v1 +build_flags = + ${esp32_base.build_flags} + -I variants/generic-e22 + -D GENERIC_E22 + -D P_LORA_TX_LED=2 + -D PIN_VBAT_READ=35 + -D P_LORA_DIO_1=33 + -D P_LORA_NSS=18 + -D P_LORA_RESET=RADIOLIB_NC + -D P_LORA_BUSY=32 + -D P_LORA_SCLK=5 + -D P_LORA_MOSI=27 + -D P_LORA_MISO=19 + -D SX126X_TXEN=13 + -D SX126X_RXEN=14 + -D PIN_BOARD_SDA=21 + -D PIN_BOARD_SCL=22 + -D SX126X_DIO2_AS_RF_SWITCH=true + -D SX126X_DIO3_TCXO_VOLTAGE=1.8 + -D SX126X_CURRENT_LIMIT=140 +build_src_filter = ${esp32_base.build_src_filter} + +<../variants/generic-e22> +lib_deps = + ${esp32_base.lib_deps} + adafruit/Adafruit SSD1306 @ ^2.5.13 + +[env:Generic_E22_sx1262_repeater] +extends = Generic_E22 +build_src_filter = ${Generic_E22.build_src_filter} + +<../examples/simple_repeater/*.cpp> +build_flags = + ${Generic_E22.build_flags} + -D RADIO_CLASS=CustomSX1262 + -D WRAPPER_CLASS=CustomSX1262Wrapper + -D LORA_TX_POWER=22 + -D ADVERT_NAME='"E22 Repeater"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 +lib_deps = + ${Generic_E22.lib_deps} + ${esp32_ota.lib_deps} + +[env:Generic_E22_sx1262_repeater_bridge_espnow] +extends = Generic_E22 +build_src_filter = ${Generic_E22.build_src_filter} + + + +<../examples/simple_repeater/*.cpp> +build_flags = + ${Generic_E22.build_flags} + -D RADIO_CLASS=CustomSX1262 + -D WRAPPER_CLASS=CustomSX1262Wrapper + -D LORA_TX_POWER=22 + -D ADVERT_NAME='"ESPNow Bridge"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 + -D WITH_ESPNOW_BRIDGE=1 +lib_deps = + ${Generic_E22.lib_deps} + ${esp32_ota.lib_deps} + +[env:Generic_E22_kiss_modem] +extends = Generic_E22 +build_src_filter = ${Generic_E22.build_src_filter} + +<../examples/kiss_modem/> + +[env:Generic_E22_sx1268_repeater] +extends = Generic_E22 +build_src_filter = ${Generic_E22.build_src_filter} + +<../examples/simple_repeater/*.cpp> +build_flags = + ${Generic_E22.build_flags} + -D RADIO_CLASS=CustomSX1268 + -D WRAPPER_CLASS=CustomSX1268Wrapper + -D LORA_TX_POWER=22 + -D ADVERT_NAME='"E22 Repeater"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 +lib_deps = + ${Generic_E22.lib_deps} + ${esp32_ota.lib_deps} + +[env:Generic_E22_sx1268_repeater_bridge_espnow] +extends = Generic_E22 +build_src_filter = ${Generic_E22.build_src_filter} + + + +<../examples/simple_repeater/*.cpp> +build_flags = + ${Generic_E22.build_flags} + -D RADIO_CLASS=CustomSX1268 + -D WRAPPER_CLASS=CustomSX1268Wrapper + -D LORA_TX_POWER=22 + -D ADVERT_NAME='"ESPNow Bridge"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 + -D WITH_ESPNOW_BRIDGE=1 +lib_deps = + ${Generic_E22.lib_deps} + ${esp32_ota.lib_deps} + +[rak4631] +extends = nrf52_base +board = rak4631 +board_check = true +extra_scripts = ${nrf52_base.extra_scripts} + post:variants/rak4631/fix_bsec_lib.py +build_flags = ${nrf52_base.build_flags} + ${sensor_base.build_flags} + -I variants/rak4631 + -D RAK_4631 + -D RAK_BOARD + -D PIN_BOARD_SCL=14 + -D PIN_BOARD_SDA=13 + -D PIN_GPS_TX=PIN_SERIAL1_RX + -D PIN_GPS_RX=PIN_SERIAL1_TX + -D PIN_GPS_EN=-1 + -D PIN_OLED_RESET=-1 + -D USE_SX1262 + -D RADIO_CLASS=CustomSX1262 + -D WRAPPER_CLASS=CustomSX1262Wrapper + -D LORA_TX_POWER=22 + -D SX126X_CURRENT_LIMIT=140 + -D SX126X_RX_BOOSTED_GAIN=1 + -D ENV_INCLUDE_RAK12035=1 + -UENV_INCLUDE_BME680 + -D ENV_INCLUDE_BME680_BSEC=1 +build_src_filter = ${nrf52_base.build_src_filter} + +<../variants/rak4631> + + + + + + + + + + +lib_deps = + ${nrf52_base.lib_deps} + ${sensor_base.lib_deps} + adafruit/Adafruit SSD1306 @ ^2.5.13 + adafruit/Adafruit SH110X @ ^2.1.13 + sparkfun/SparkFun u-blox GNSS Arduino Library@^2.2.27 + boschsensortec/BSEC Software Library @ ^1.8.1492 + +[env:RAK_4631_repeater] +extends = rak4631 +build_flags = + ${rak4631.build_flags} + -D DISPLAY_CLASS=AutoDetectDisplay + -D ADVERT_NAME='"RAK4631 Repeater"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 +build_src_filter = ${rak4631.build_src_filter} + + + +<../examples/simple_repeater> + +[env:RAK_4631_repeater_ethernet] +extends = rak4631 +build_flags = + ${rak4631.build_flags} + -D DISPLAY_CLASS=AutoDetectDisplay + -D ADVERT_NAME='"RAK4631 Repeater"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 + -D ETHERNET_ENABLED=1 +build_src_filter = ${rak4631.build_src_filter} + + + +<../examples/simple_repeater> +lib_deps = + ${rak4631.lib_deps} + https://github.com/RAKWireless/RAK13800-W5100S/archive/1.0.2.zip + +[env:RAK_4631_repeater_bridge_rs232_serial1] +extends = rak4631 +build_flags = + ${rak4631.build_flags} + -D DISPLAY_CLASS=AutoDetectDisplay + -D ADVERT_NAME='"RS232 Bridge"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 + -D WITH_RS232_BRIDGE=Serial1 + -D WITH_RS232_BRIDGE_RX=PIN_SERIAL1_RX + -D WITH_RS232_BRIDGE_TX=PIN_SERIAL1_TX + -UENV_INCLUDE_GPS +build_src_filter = ${rak4631.build_src_filter} + + + + + +<../examples/simple_repeater> + +[env:RAK_4631_repeater_bridge_rs232_serial2] +extends = rak4631 +build_flags = + ${rak4631.build_flags} + -D DISPLAY_CLASS=AutoDetectDisplay + -D ADVERT_NAME='"RS232 Bridge"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 + -D WITH_RS232_BRIDGE=Serial2 + -D WITH_RS232_BRIDGE_RX=PIN_SERIAL2_RX + -D WITH_RS232_BRIDGE_TX=PIN_SERIAL2_TX + -UENV_INCLUDE_GPS +build_src_filter = ${rak4631.build_src_filter} + + + + + +<../examples/simple_repeater> + +[env:RAK_4631_room_server] +extends = rak4631 +build_flags = + ${rak4631.build_flags} + -D DISPLAY_CLASS=AutoDetectDisplay + -D ADVERT_NAME='"Test Room"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D ROOM_PASSWORD='"hello"' +build_src_filter = ${rak4631.build_src_filter} + + + +<../examples/simple_room_server> + +[env:RAK_4631_room_server_ethernet] +extends = rak4631 +build_flags = + ${rak4631.build_flags} + -D DISPLAY_CLASS=AutoDetectDisplay + -D ADVERT_NAME='"RAK4631 Room Server"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D ROOM_PASSWORD='"hello"' + -D ETHERNET_ENABLED=1 +build_src_filter = ${rak4631.build_src_filter} + + + +<../examples/simple_room_server> +lib_deps = + ${rak4631.lib_deps} + https://github.com/RAKWireless/RAK13800-W5100S/archive/1.0.2.zip + +[env:RAK_4631_companion_radio_usb] +extends = rak4631 +board_build.ldscript = boards/nrf52840_s140_v6_extrafs.ld +board_upload.maximum_size = 712704 +build_flags = + ${rak4631.build_flags} + -I examples/companion_radio/ui-new + -D PIN_USER_BTN=9 + -D PIN_USER_BTN_ANA=31 + -D DISPLAY_CLASS=AutoDetectDisplay + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D ENABLE_USB_INTERFACE +build_src_filter = ${rak4631.build_src_filter} + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${rak4631.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:RAK_4631_companion_radio_ethernet] +extends = rak4631 +board_build.ldscript = boards/nrf52840_s140_v6.ld +board_upload.maximum_size = 712704 +build_unflags = + -D EXTRAFS=1 +build_flags = + ${rak4631.build_flags} + -I examples/companion_radio/ui-new + -D PIN_USER_BTN=9 + -D PIN_USER_BTN_ANA=31 + -D DISPLAY_CLASS=AutoDetectDisplay + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D ETHERNET_ENABLED=1 + -D ETHERNET_USE_RAK13800 + -D ETHERNET_CLASS=RAK13800EthernetInterface +build_src_filter = ${rak4631.build_src_filter} + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> + + + + +lib_deps = + ${rak4631.lib_deps} + densaugeo/base64 @ ~1.4.0 + https://github.com/RAKWireless/RAK13800-W5100S/archive/1.0.2.zip + +[env:RAK_4631_companion_radio_ble] +extends = rak4631 +board_build.ldscript = boards/nrf52840_s140_v6_extrafs.ld +board_upload.maximum_size = 712704 +build_flags = + ${rak4631.build_flags} + -I examples/companion_radio/ui-new + -D PIN_USER_BTN=9 + -D PIN_USER_BTN_ANA=31 + -D DISPLAY_CLASS=AutoDetectDisplay + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D BLE_PIN_CODE=123456 + -D BLE_DEBUG_LOGGING=1 + -D OFFLINE_QUEUE_SIZE=256 +build_src_filter = ${rak4631.build_src_filter} + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> +lib_deps = + ${rak4631.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:RAK_4631_terminal_chat] +extends = rak4631 +build_flags = + ${rak4631.build_flags} + -D PIN_USER_BTN=9 + -D PIN_USER_BTN_ANA=31 + -D MAX_CONTACTS=100 + -D MAX_GROUP_CHANNELS=1 +build_src_filter = ${rak4631.build_src_filter} + +<../examples/simple_secure_chat/main.cpp> +lib_deps = + ${rak4631.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:RAK_4631_sensor] +extends = rak4631 +build_flags = + ${rak4631.build_flags} + -D DISPLAY_CLASS=AutoDetectDisplay + -D ADVERT_NAME='"RAK4631 Sensor"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' +build_src_filter = ${rak4631.build_src_filter} + + + +<../examples/simple_sensor> + +[env:RAK_4631_kiss_modem] +extends = rak4631 +build_flags = + ${rak4631.build_flags} +build_src_filter = ${rak4631.build_src_filter} + +<../examples/kiss_modem/> +lib_deps = + ${rak4631.lib_deps} + +[t1000-e] +extends = nrf52_base +board = tracker-t1000-e +board_build.ldscript = boards/nrf52840_s140_v7.ld +build_flags = ${nrf52_base.build_flags} + -I src/helpers/nrf52 + -I lib/nrf52/s140_nrf52_7.3.0_API/include + -I lib/nrf52/s140_nrf52_7.3.0_API/include/nrf52 + -I variants/t1000-e + -I src/helpers/ui + -D T1000_E + -D PIN_USER_BTN=6 + -D USER_BTN_PRESSED=HIGH + -D PIN_STATUS_LED=24 + -D RADIO_CLASS=CustomLR1110 + -D USE_LR1110 + -D WRAPPER_CLASS=CustomLR1110Wrapper + -D LORA_TX_POWER=22 + -D RF_SWITCH_TABLE + -D RX_BOOSTED_GAIN=true + -D P_LORA_BUSY=7 + -D P_LORA_SCLK=11 + -D P_LORA_NSS=12 + -D P_LORA_DIO_1=33 + -D P_LORA_MISO=40 + -D P_LORA_MOSI=41 + -D P_LORA_RESET=42 + -D LR11X0_DIO_AS_RF_SWITCH=true + -D LR11X0_DIO3_TCXO_VOLTAGE=1.6 + -D ENV_INCLUDE_GPS=1 +build_src_filter = ${nrf52_base.build_src_filter} + + + + + +<../variants/t1000-e> +debug_tool = jlink +upload_protocol = nrfutil + +[env:t1000e_repeater] +extends = t1000-e +build_flags = ${t1000-e.build_flags} + -I examples/companion_radio/ui-orig + -D ADVERT_NAME='"t1000-e Repeater"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 +build_src_filter = ${t1000-e.build_src_filter} + +<../examples/simple_repeater> +lib_deps = ${t1000-e.lib_deps} + stevemarple/MicroNMEA @ ^2.0.6 + +[env:t1000e_room_server] +extends = t1000-e +build_flags = ${t1000-e.build_flags} + -I examples/companion_radio/ui-orig + -D ADVERT_NAME='"t1000-e Room"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D ROOM_PASSWORD='"hello"' + -D RF_SWITCH_TABLE +build_src_filter = ${t1000-e.build_src_filter} + +<../examples/simple_room_server> +lib_deps = ${t1000-e.lib_deps} + stevemarple/MicroNMEA @ ^2.0.6 + +[env:t1000e_companion_radio_usb] +extends = t1000-e +board_build.ldscript = boards/nrf52840_s140_v7_extrafs.ld +board_upload.maximum_size = 708608 +build_flags = ${t1000-e.build_flags} + -I examples/companion_radio/ui-orig + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D OFFLINE_QUEUE_SIZE=256 + -D DISPLAY_CLASS=NullDisplayDriver + -D PIN_BUZZER=25 + -D PIN_BUZZER_EN=37 + -D ENABLE_USB_INTERFACE +build_src_filter = ${t1000-e.build_src_filter} + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-orig/*.cpp> +lib_deps = ${t1000-e.lib_deps} + densaugeo/base64 @ ~1.4.0 + stevemarple/MicroNMEA @ ^2.0.6 + end2endzone/NonBlockingRTTTL@^1.3.0 + +[env:t1000e_companion_radio_ble] +extends = t1000-e +board_build.ldscript = boards/nrf52840_s140_v7_extrafs.ld +board_upload.maximum_size = 708608 +build_flags = ${t1000-e.build_flags} + -I examples/companion_radio/ui-orig + -D MAX_CONTACTS=350 + -D MAX_GROUP_CHANNELS=40 + -D BLE_PIN_CODE=123456 + -D BLE_TX_POWER=0 + -D OFFLINE_QUEUE_SIZE=256 + -D DISPLAY_CLASS=NullDisplayDriver + -D PIN_BUZZER=25 + -D PIN_BUZZER_EN=37 + -D ADVERT_NAME='"@@MAC"' +build_src_filter = ${t1000-e.build_src_filter} + + + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-orig/*.cpp> +lib_deps = ${t1000-e.lib_deps} + densaugeo/base64 @ ~1.4.0 + stevemarple/MicroNMEA @ ^2.0.6 + end2endzone/NonBlockingRTTTL@^1.3.0 + +[env:t1000e_kiss_modem] +extends = t1000-e +build_src_filter = ${t1000-e.build_src_filter} + +<../examples/kiss_modem/> +lib_deps = ${t1000-e.lib_deps} + stevemarple/MicroNMEA @ ^2.0.6 diff --git a/src/helpers/sensors/EnvironmentSensorManager.cpp b/src/helpers/sensors/EnvironmentSensorManager.cpp index 0dc892c3a52..28bb25b28c8 100644 --- a/src/helpers/sensors/EnvironmentSensorManager.cpp +++ b/src/helpers/sensors/EnvironmentSensorManager.cpp @@ -1,11 +1,14 @@ #include "EnvironmentSensorManager.h" -#include +// Include board headers for power management +#ifdef HELTEC_LORA_V3 +#include <../variants/heltec_v3/HeltecV3Board.h> +#endif #if ENV_PIN_SDA && ENV_PIN_SCL -#define TELEM_WIRE &Wire1 // Use Wire1 as the I2C bus for Environment Sensors +#define TELEM_WIRE &Wire1 // Use Wire1 as the I2C bus for Environment Sensors #else -#define TELEM_WIRE &Wire // Use default I2C bus for Environment Sensors +#define TELEM_WIRE &Wire // Use default I2C bus for Environment Sensors #endif // ============================================================ @@ -39,11 +42,40 @@ static uint32_t bsec_last_save_ms = 0; #ifdef ENV_INCLUDE_BME680 #ifndef TELEM_BME680_ADDRESS -#define TELEM_BME680_ADDRESS 0x76 +#define TELEM_BME680_ADDRESS 0x76 #endif + #define TELEM_BME680_SEALEVELPRESSURE_HPA (1013.25) + +#ifndef BME680_BSEC2_SUPPORTED +#define BME680_BSEC2_SUPPORTED 0 +#endif + +// Geoidal separation (geoid height above WGS84 ellipsoid) for altitude correction +// This is location-specific. Default is 0, can be overridden in platformio.ini +#ifndef GEOIDAL_SEPARATION +#define GEOIDAL_SEPARATION 0.0 +#endif + +#ifdef BME680_BSEC2_SUPPORTED +// Use BSEC2 library for IAQ support +#include +static Bsec2 BME680_BSEC; + +// BSEC configuration for 3 second sample rate +const uint8_t bsec_config[] = { +#include "config/bme680/bme680_iaq_33v_3s_4d/bsec_iaq.txt" +}; + +#else +// Use Adafruit BME680 library (no IAQ) #include -static Adafruit_BME680 BME680(TELEM_WIRE); +#if ENV_PIN_SDA && ENV_PIN_SCL +static Adafruit_BME680 BME680(&Wire1); // Use Wire1 for sensors +#else +static Adafruit_BME680 BME680(&Wire); // Use default Wire +#endif +#endif #endif #ifdef ENV_INCLUDE_BMP085 @@ -53,27 +85,25 @@ static Adafruit_BMP085 BMP085; #endif #if ENV_INCLUDE_AHTX0 -#ifndef TELEM_AHTX_ADDRESS -#define TELEM_AHTX_ADDRESS 0x38 // AHT10, AHT20 temperature and humidity sensor I2C address -#endif +#define TELEM_AHTX_ADDRESS 0x38 // AHT10, AHT20 temperature and humidity sensor I2C address #include static Adafruit_AHTX0 AHTX0; #endif #if ENV_INCLUDE_BME280 #ifndef TELEM_BME280_ADDRESS -#define TELEM_BME280_ADDRESS 0x76 // BME280 environmental sensor I2C address +#define TELEM_BME280_ADDRESS 0x76 // BME280 environmental sensor I2C address #endif -#define TELEM_BME280_SEALEVELPRESSURE_HPA (1013.25) // Atmospheric pressure at sea level +#define TELEM_BME280_SEALEVELPRESSURE_HPA (1013.25) // Athmospheric pressure at sea level #include static Adafruit_BME280 BME280; #endif #if ENV_INCLUDE_BMP280 #ifndef TELEM_BMP280_ADDRESS -#define TELEM_BMP280_ADDRESS 0x76 // BMP280 environmental sensor I2C address +#define TELEM_BMP280_ADDRESS 0x76 // BMP280 environmental sensor I2C address #endif -#define TELEM_BMP280_SEALEVELPRESSURE_HPA (1013.25) // Atmospheric pressure at sea level +#define TELEM_BMP280_SEALEVELPRESSURE_HPA (1013.25) // Athmospheric pressure at sea level #include static Adafruit_BMP280 BMP280(TELEM_WIRE); #endif @@ -133,7 +163,7 @@ static Adafruit_INA260 INA260; #define TELEM_INA226_SHUNT_VALUE 0.100 #define TELEM_INA226_MAX_AMP 0.8 #include -static INA226 INA226(TELEM_INA226_ADDRESS, TELEM_WIRE); +static INA226 INA226_sensor(TELEM_INA226_ADDRESS, TELEM_WIRE); #endif #if ENV_INCLUDE_MLX90614 @@ -181,6 +211,7 @@ class RAK12500LocationProvider : public LocationProvider { int _sats = 0; long _epoch = 0; bool _fix = false; + public: long getLatitude() override { return _lat; } long getLongitude() override { return _lng; } @@ -188,10 +219,10 @@ class RAK12500LocationProvider : public LocationProvider { long satellitesCount() override { return _sats; } bool isValid() override { return _fix; } long getTimestamp() override { return _epoch; } - void sendSentence(const char * sentence) override { } - void reset() override { } - void begin() override { } - void stop() override { } + void sendSentence(const char *sentence) override {} + void reset() override {} + void begin() override {} + void stop() override {} void loop() override { if (ublox_GNSS.getGnssFixOk(8)) { _fix = true; @@ -211,524 +242,702 @@ static RAK12500LocationProvider RAK12500_provider; #endif // ============================================================ -// I2C bus scanner -// Probes every valid address and records which ones ACK. -// This runs before any sensor library is touched, so a missing -// or misbehaving device cannot stall or crash the boot sequence. +// I2C helpers // ============================================================ -static void scanI2CBus(TwoWire* wire, bool found[128]) { - for (uint8_t addr = 0x08; addr < 0x78; addr++) { - wire->beginTransmission(addr); - found[addr] = (wire->endTransmission() == 0); +// I2C device scanner - checks if a device responds at the given address +static bool i2c_device_exists(TwoWire *wire, uint8_t address) { + wire->beginTransmission(address); + uint8_t error = wire->endTransmission(); + delay(20); + return (error == 0); +} + +// Read chip ID from Bosch sensors (BME/BMP family) - register 0xD0 +static uint8_t read_chip_id(TwoWire *wire, uint8_t address) { + wire->beginTransmission(address); + wire->write(0xD0); // Chip ID register for Bosch sensors + if (wire->endTransmission() != 0) { + delay(20); + return 0x00; // Communication failed + } + delay(10); + wire->requestFrom(address, (uint8_t)1); + if (wire->available()) { + uint8_t chip_id = wire->read(); + delay(20); + return chip_id; } + delay(20); + return 0x00; } -// ============================================================ -// Per-sensor init and query functions -// -// init(wire, address) — called only when the address was seen -// on the bus. Returns 0 on failure, or the number of -// telemetry channels the sensor will consume (1 for all -// single-output sensors; INA3221 returns one per enabled -// hardware channel; MLX90614 and RAK12035+calibration -// return 2). -// -// query(channel, sub_channel, lpp) — called once per active -// sensor entry during querySensors(). sub_channel is always -// 0 for single-output sensors. -// ============================================================ +// Get geoidal separation based on GPS coordinates +// Simple lookup table for common regions - accuracy ~5m +static float get_geoidal_separation(double lat, double lon) { + MESH_DEBUG_PRINTLN("Calculating geoidal separation for lat: %.6f, lon: %.6f", lat, lon); -#if ENV_INCLUDE_AHTX0 -static uint8_t init_ahtx0(TwoWire* wire, uint8_t addr) { - return AHTX0.begin(wire, 0, addr) ? 1 : 0; + // North America + if (lat >= 25 && lat <= 70 && lon >= -170 && lon <= -50) { + if (lat >= 50) return -10.0; + if (lat >= 35) return -25.0; + return -15.0; + } + // Europe + if (lat >= 35 && lat <= 72 && lon >= -10 && lon <= 45) { + if (lat >= 60) return 25.0; + if (lat >= 50) return 45.0; + if (lat >= 45) return 48.0; + return 50.0; + } + // Asia + if (lat >= -10 && lat <= 75 && lon >= 45 && lon <= 180) { + if (lat >= 40) return -10.0; + if (lat >= 20) return -5.0; + return 0.0; + } + // Australia/Oceania + if (lat >= -50 && lat <= -10 && lon >= 110 && lon <= 180) { + return 10.0; + } + // South America + if (lat >= -60 && lat <= 15 && lon >= -85 && lon <= -30) { + if (lat >= 0) return 5.0; + if (lat >= -30) return 15.0; + return 0.0; + } + // Africa + if (lat >= -35 && lat <= 38 && lon >= -20 && lon <= 55) { + if (lat >= 20) return 0.0; + if (lat >= 0) return 5.0; + return 20.0; + } + return 0.0; } -static void query_ahtx0(uint8_t ch, uint8_t, CayenneLPP& lpp) { - sensors_event_t humidity, temp; - AHTX0.getEvent(&humidity, &temp); - lpp.addTemperature(ch, temp.temperature); - lpp.addRelativeHumidity(ch, humidity.relative_humidity); + +#if ENV_INCLUDE_BME680_BSEC +static void bsec_load_state() { + using namespace Adafruit_LittleFS_Namespace; + File f = InternalFS.open(BSEC_STATE_FILE, FILE_O_READ); + if (!f) return; + uint8_t state[BSEC_MAX_STATE_BLOB_SIZE]; + f.read(state, BSEC_MAX_STATE_BLOB_SIZE); + f.close(); + bsec_iaq.setState(state); } -#endif -#ifdef ENV_INCLUDE_BME680 -static uint8_t init_bme680(TwoWire*, uint8_t addr) { - // Wire was set in the static constructor; begin() takes address only. - return BME680.begin(addr) ? 1 : 0; +static void bsec_save_state() { + using namespace Adafruit_LittleFS_Namespace; + uint8_t state[BSEC_MAX_STATE_BLOB_SIZE]; + bsec_iaq.getState(state); + InternalFS.remove(BSEC_STATE_FILE); + File f = InternalFS.open(BSEC_STATE_FILE, FILE_O_WRITE); + if (!f) return; + f.write(state, BSEC_MAX_STATE_BLOB_SIZE); + f.close(); } -static void query_bme680(uint8_t ch, uint8_t, CayenneLPP& lpp) { - if (BME680.performReading()) { - lpp.addTemperature(ch, BME680.temperature); - lpp.addRelativeHumidity(ch, BME680.humidity); - const float pressure_hpa = BME680.pressure / 100.0f; - lpp.addBarometricPressure(ch, pressure_hpa); - lpp.addAltitude(ch, 44330.0f * (1.0f - powf(pressure_hpa / (float)TELEM_BME680_SEALEVELPRESSURE_HPA, 0.1903f))); - lpp.addGenericSensor(ch, BME680.gas_resistance); +#endif + +// ============================================================ +// begin() +// ============================================================ + +bool EnvironmentSensorManager::begin() { +#if ENV_INCLUDE_GPS +#ifdef RAK_WISBLOCK_GPS + rakGPSInit(); +#else + initBasicGPS(); +#endif +#endif + +#if ENV_PIN_SDA && ENV_PIN_SCL +#ifdef NRF52_PLATFORM + Wire1.setPins(ENV_PIN_SDA, ENV_PIN_SCL); + Wire1.setClock(100000); + Wire1.begin(); +#else + Wire1.begin(ENV_PIN_SDA, ENV_PIN_SCL, 100000); +#endif + MESH_DEBUG_PRINTLN("Second I2C initialized on pins SDA: %d SCL: %d", ENV_PIN_SDA, ENV_PIN_SCL); +#endif + +#if ENV_INCLUDE_BME680 + if (i2c_device_exists(TELEM_WIRE, TELEM_BME680_ADDRESS)) { + uint8_t chip_id = read_chip_id(TELEM_WIRE, TELEM_BME680_ADDRESS); + MESH_DEBUG_PRINTLN("Chip ID at address %02X: 0x%02X", TELEM_BME680_ADDRESS, chip_id); + + if (chip_id == 0x61) { + MESH_DEBUG_PRINTLN("Confirmed BME680 chip, initializing..."); + delay(100); + +#ifdef BME680_BSEC2_SUPPORTED + if (BME680_BSEC.begin(TELEM_BME680_ADDRESS, *TELEM_WIRE)) { + if (BME680_BSEC.status == BSEC_OK) { + MESH_DEBUG_PRINTLN("BSEC2 sensor communication OK"); + BME680_BSEC.setConfig(bsec_config); + bsecSensor sensorList[] = { BSEC_OUTPUT_IAQ, + BSEC_OUTPUT_RAW_TEMPERATURE, + BSEC_OUTPUT_RAW_PRESSURE, + BSEC_OUTPUT_RAW_HUMIDITY, + BSEC_OUTPUT_RAW_GAS, + BSEC_OUTPUT_STABILIZATION_STATUS, + BSEC_OUTPUT_RUN_IN_STATUS, + BSEC_OUTPUT_SENSOR_HEAT_COMPENSATED_TEMPERATURE, + BSEC_OUTPUT_SENSOR_HEAT_COMPENSATED_HUMIDITY }; + if (!BME680_BSEC.updateSubscription(sensorList, 9, BSEC_SAMPLE_RATE_LP)) { + MESH_DEBUG_PRINTLN("BSEC LP mode failed, trying ULP mode..."); + if (!BME680_BSEC.updateSubscription(sensorList, 9, BSEC_SAMPLE_RATE_ULP)) { + MESH_DEBUG_PRINTLN("BSEC ULP mode also failed!"); + BME680_initialized = false; + } else { + MESH_DEBUG_PRINTLN("Init BME680 with BSEC Library version %d.%d.%d.%d (ULP mode)", + BME680_BSEC.version.major, BME680_BSEC.version.minor, + BME680_BSEC.version.major_bugfix, BME680_BSEC.version.minor_bugfix); + BME680_initialized = true; + } + } else { + MESH_DEBUG_PRINTLN("Init BME680 with BSEC Library version %d.%d.%d.%d (LP mode)", + BME680_BSEC.version.major, BME680_BSEC.version.minor, + BME680_BSEC.version.major_bugfix, BME680_BSEC.version.minor_bugfix); + BME680_initialized = true; + } + } else { + BME680_initialized = false; + MESH_DEBUG_PRINTLN("BSEC initialization failed, status: %d", BME680_BSEC.status); + } + } else { + BME680_initialized = false; + MESH_DEBUG_PRINTLN("BME680 BSEC failed to begin at address %02X", TELEM_BME680_ADDRESS); + } +#else + if (BME680.begin(TELEM_BME680_ADDRESS)) { + MESH_DEBUG_PRINTLN("Found BME680 at address: %02X (Adafruit library)", TELEM_BME680_ADDRESS); + BME680.setTemperatureOversampling(BME680_OS_8X); + BME680.setHumidityOversampling(BME680_OS_2X); + BME680.setPressureOversampling(BME680_OS_4X); + BME680.setIIRFilterSize(BME680_FILTER_SIZE_3); + BME680.setGasHeater(320, 150); + BME680_initialized = true; + } else { + BME680_initialized = false; + MESH_DEBUG_PRINTLN("BME680 chip detected but init failed at address %02X", TELEM_BME680_ADDRESS); + } +#endif + } else { + BME680_initialized = false; + MESH_DEBUG_PRINTLN("Not a BME680 at address %02X (chip ID: 0x%02X)", TELEM_BME680_ADDRESS, chip_id); + } + } else { + BME680_initialized = false; + MESH_DEBUG_PRINTLN("No I2C device found at address %02X (BME680)", TELEM_BME680_ADDRESS); + } +#endif + + +#if ENV_INCLUDE_BME680_BSEC + if (i2c_device_exists(TELEM_WIRE, TELEM_BME680_ADDRESS)) { + bsec_iaq.begin(TELEM_BME680_ADDRESS, *TELEM_WIRE); + if (bsec_iaq.bsecStatus == BSEC_OK) { + bsec_iaq.setConfig(bsec_config_iaq); + if (bsec_iaq.bsecStatus == BSEC_OK) { + bsec_virtual_sensor_t outputs[] = { + BSEC_OUTPUT_IAQ, + BSEC_OUTPUT_SENSOR_HEAT_COMPENSATED_TEMPERATURE, + BSEC_OUTPUT_SENSOR_HEAT_COMPENSATED_HUMIDITY, + BSEC_OUTPUT_RAW_PRESSURE, + BSEC_OUTPUT_STABILIZATION_STATUS, + BSEC_OUTPUT_RUN_IN_STATUS, + }; + bsec_iaq.updateSubscription(outputs, 6, BSEC_SAMPLE_RATE_LP); + if (bsec_iaq.bsecStatus == BSEC_OK) { + bsec_load_state(); + bsec_active = true; + MESH_DEBUG_PRINTLN("Found BME680+BSEC at address: %02X", TELEM_BME680_ADDRESS); + } else { + MESH_DEBUG_PRINTLN("BME680+BSEC subscription failed, status: %d", bsec_iaq.bsecStatus); + } + } else { + MESH_DEBUG_PRINTLN("BME680+BSEC setConfig failed, status: %d", bsec_iaq.bsecStatus); + } + } else { + MESH_DEBUG_PRINTLN("BME680+BSEC begin failed, status: %d", bsec_iaq.bsecStatus); + } + } else { + MESH_DEBUG_PRINTLN("No I2C device found at address %02X (BME680+BSEC)", TELEM_BME680_ADDRESS); + } +#endif + +#if ENV_INCLUDE_AHTX0 + if (i2c_device_exists(TELEM_WIRE, TELEM_AHTX_ADDRESS)) { + if (AHTX0.begin(TELEM_WIRE, 0, TELEM_AHTX_ADDRESS)) { + MESH_DEBUG_PRINTLN("Found AHT10/AHT20 at address: %02X", TELEM_AHTX_ADDRESS); + AHTX0_initialized = true; + } else { + AHTX0_initialized = false; + MESH_DEBUG_PRINTLN("AHT10/AHT20 did not initialize at I2C address %02X", TELEM_AHTX_ADDRESS); + } + } else { + AHTX0_initialized = false; + MESH_DEBUG_PRINTLN("No I2C device found at address %02X (AHT10/AHT20)", TELEM_AHTX_ADDRESS); } -} #endif #if ENV_INCLUDE_BME280 -static uint8_t init_bme280(TwoWire* wire, uint8_t addr) { - if (!BME280.begin(addr, wire)) return 0; - BME280.setSampling(Adafruit_BME280::MODE_FORCED, - Adafruit_BME280::SAMPLING_X1, - Adafruit_BME280::SAMPLING_X1, - Adafruit_BME280::SAMPLING_X1, - Adafruit_BME280::FILTER_OFF, - Adafruit_BME280::STANDBY_MS_1000); - return 1; -} -static void query_bme280(uint8_t ch, uint8_t, CayenneLPP& lpp) { - if (BME280.takeForcedMeasurement()) { - lpp.addTemperature(ch, BME280.readTemperature()); - lpp.addRelativeHumidity(ch, BME280.readHumidity()); - lpp.addBarometricPressure(ch, BME280.readPressure() / 100); - lpp.addAltitude(ch, BME280.readAltitude(TELEM_BME280_SEALEVELPRESSURE_HPA)); + if (i2c_device_exists(TELEM_WIRE, TELEM_BME280_ADDRESS)) { + uint8_t chip_id = read_chip_id(TELEM_WIRE, TELEM_BME280_ADDRESS); + if (chip_id == 0x60) { + if (BME280.begin(TELEM_BME280_ADDRESS, TELEM_WIRE)) { + MESH_DEBUG_PRINTLN("Found BME280 at address: %02X (chip ID: 0x60)", TELEM_BME280_ADDRESS); + MESH_DEBUG_PRINTLN("BME sensor ID: %02X", BME280.sensorID()); + BME280.setSampling(Adafruit_BME280::MODE_FORCED, + Adafruit_BME280::SAMPLING_X1, + Adafruit_BME280::SAMPLING_X1, + Adafruit_BME280::SAMPLING_X1, + Adafruit_BME280::FILTER_OFF, Adafruit_BME280::STANDBY_MS_1000); + BME280_initialized = true; + } else { + BME280_initialized = false; + MESH_DEBUG_PRINTLN("BME280 chip detected but init failed at address %02X", TELEM_BME280_ADDRESS); + } + } else { + BME280_initialized = false; + MESH_DEBUG_PRINTLN("Not a BME280 at address %02X (chip ID: 0x%02X)", TELEM_BME280_ADDRESS, chip_id); + } + } else { + BME280_initialized = false; + MESH_DEBUG_PRINTLN("No I2C device found at address %02X (BME280)", TELEM_BME280_ADDRESS); } -} #endif #if ENV_INCLUDE_BMP280 -static uint8_t init_bmp280(TwoWire*, uint8_t addr) { - // BMP280 static instance was constructed with TELEM_WIRE; begin() uses it. - return BMP280.begin(addr) ? 1 : 0; -} -static void query_bmp280(uint8_t ch, uint8_t, CayenneLPP& lpp) { - lpp.addTemperature(ch, BMP280.readTemperature()); - lpp.addBarometricPressure(ch, BMP280.readPressure() / 100); - lpp.addAltitude(ch, BMP280.readAltitude(TELEM_BMP280_SEALEVELPRESSURE_HPA)); -} + if (i2c_device_exists(TELEM_WIRE, TELEM_BMP280_ADDRESS)) { + uint8_t chip_id = read_chip_id(TELEM_WIRE, TELEM_BMP280_ADDRESS); + if (chip_id == 0x58) { + if (BMP280.begin(TELEM_BMP280_ADDRESS)) { + MESH_DEBUG_PRINTLN("Found BMP280 at address: %02X (chip ID: 0x58)", TELEM_BMP280_ADDRESS); + BMP280_initialized = true; + } else { + BMP280_initialized = false; + MESH_DEBUG_PRINTLN("BMP280 chip detected but init failed at address %02X", TELEM_BMP280_ADDRESS); + } + } else { + BMP280_initialized = false; + MESH_DEBUG_PRINTLN("Not a BMP280 at address %02X (chip ID: 0x%02X)", TELEM_BMP280_ADDRESS, chip_id); + } + } else { + BMP280_initialized = false; + MESH_DEBUG_PRINTLN("No I2C device found at address %02X (BMP280)", TELEM_BMP280_ADDRESS); + } #endif #if ENV_INCLUDE_SHTC3 -static uint8_t init_shtc3(TwoWire* wire, uint8_t) { - // Adafruit_SHTC3::begin() does not accept an address (fixed at 0x70). - return SHTC3.begin(wire) ? 1 : 0; -} -static void query_shtc3(uint8_t ch, uint8_t, CayenneLPP& lpp) { - sensors_event_t humidity, temp; - SHTC3.getEvent(&humidity, &temp); - lpp.addTemperature(ch, temp.temperature); - lpp.addRelativeHumidity(ch, humidity.relative_humidity); -} + if (i2c_device_exists(TELEM_WIRE, 0x70)) { + if (SHTC3.begin(TELEM_WIRE)) { + MESH_DEBUG_PRINTLN("Found sensor: SHTC3"); + SHTC3_initialized = true; + } else { + SHTC3_initialized = false; + MESH_DEBUG_PRINTLN("SHTC3 did not initialize at I2C address %02X", 0x70); + } + } else { + SHTC3_initialized = false; + MESH_DEBUG_PRINTLN("No I2C device found at address %02X (SHTC3)", 0x70); + } #endif #if ENV_INCLUDE_SHT4X -static uint8_t init_sht4x(TwoWire* wire, uint8_t addr) { - // SensirionI2cSht4x::begin() does not probe the hardware; use serialNumber() - // as the actual presence check since it performs a real I2C transaction. - SHT4X.begin(*wire, addr); - uint32_t serial = 0; - return (SHT4X.serialNumber(serial) == 0) ? 1 : 0; -} -static void query_sht4x(uint8_t ch, uint8_t, CayenneLPP& lpp) { - float temperature, humidity; - if (SHT4X.measureLowestPrecision(temperature, humidity) == 0) { - lpp.addTemperature(ch, temperature); - lpp.addRelativeHumidity(ch, humidity); + if (i2c_device_exists(TELEM_WIRE, TELEM_SHT4X_ADDRESS)) { + SHT4X.begin(*TELEM_WIRE, TELEM_SHT4X_ADDRESS); + uint32_t serialNumber = 0; + int16_t sht4x_error = SHT4X.serialNumber(serialNumber); + if (sht4x_error == 0) { + MESH_DEBUG_PRINTLN("Found SHT4X at address: %02X", TELEM_SHT4X_ADDRESS); + SHT4X_initialized = true; + } else { + SHT4X_initialized = false; + MESH_DEBUG_PRINTLN("SHT4X did not initialize at I2C address %02X", TELEM_SHT4X_ADDRESS); + } + } else { + SHT4X_initialized = false; + MESH_DEBUG_PRINTLN("No I2C device found at address %02X (SHT4X)", TELEM_SHT4X_ADDRESS); } -} #endif #if ENV_INCLUDE_LPS22HB -static uint8_t init_lps22hb(TwoWire*, uint8_t) { - // LPS22HBClass is constructed with the wire reference; begin() uses it. - return LPS22HB.begin() ? 1 : 0; -} -static void query_lps22hb(uint8_t ch, uint8_t, CayenneLPP& lpp) { - lpp.addTemperature(ch, LPS22HB.readTemperature()); - lpp.addBarometricPressure(ch, LPS22HB.readPressure() * 10); // convert kPa to hPa -} + if (i2c_device_exists(TELEM_WIRE, 0x5C)) { + if (LPS22HB.begin()) { + MESH_DEBUG_PRINTLN("Found sensor: LPS22HB"); + LPS22HB_initialized = true; + } else { + LPS22HB_initialized = false; + MESH_DEBUG_PRINTLN("LPS22HB did not initialize at I2C address %02X", 0x5C); + } + } else { + LPS22HB_initialized = false; + MESH_DEBUG_PRINTLN("No I2C device found at address %02X (LPS22HB)", 0x5C); + } #endif #if ENV_INCLUDE_INA3221 -static uint8_t init_ina3221(TwoWire* wire, uint8_t addr) { - if (!INA3221.begin(addr, wire)) return 0; - for (int i = 0; i < TELEM_INA3221_NUM_CHANNELS; i++) { - INA3221.setShuntResistance(i, TELEM_INA3221_SHUNT_VALUE); - } - // Each enabled hardware channel becomes its own telemetry channel. - uint8_t enabled = 0; - for (int i = 0; i < TELEM_INA3221_NUM_CHANNELS; i++) { - if (INA3221.isChannelEnabled(i)) enabled++; - } - return enabled > 0 ? enabled : 1; -} -static void query_ina3221(uint8_t ch, uint8_t sub_ch, CayenneLPP& lpp) { - // sub_ch is the index of the nth enabled hardware channel. - uint8_t seen = 0; - for (int i = 0; i < TELEM_INA3221_NUM_CHANNELS; i++) { - if (INA3221.isChannelEnabled(i)) { - if (seen == sub_ch) { - float v = INA3221.getBusVoltage(i); - float c = INA3221.getCurrentAmps(i); - lpp.addVoltage(ch, v); - lpp.addCurrent(ch, c); - lpp.addPower(ch, v * c); - return; - } - seen++; + if (INA3221.begin(TELEM_INA3221_ADDRESS, TELEM_WIRE)) { + MESH_DEBUG_PRINTLN("Found INA3221 at address: %02X", TELEM_INA3221_ADDRESS); + MESH_DEBUG_PRINTLN("%04X %04X", INA3221.getDieID(), INA3221.getManufacturerID()); + for (int i = 0; i < 3; i++) { + INA3221.setShuntResistance(i, TELEM_INA3221_SHUNT_VALUE); } + INA3221_initialized = true; } -} #endif #if ENV_INCLUDE_INA219 -static uint8_t init_ina219(TwoWire* wire, uint8_t) { - // INA219 static instance was constructed with the address; begin() uses it. - return INA219.begin(wire) ? 1 : 0; -} -static void query_ina219(uint8_t ch, uint8_t, CayenneLPP& lpp) { - lpp.addVoltage(ch, INA219.getBusVoltage_V()); - lpp.addCurrent(ch, INA219.getCurrent_mA() / 1000.0f); - lpp.addPower(ch, INA219.getPower_mW() / 1000.0f); -} + if (i2c_device_exists(TELEM_WIRE, TELEM_INA219_ADDRESS)) { + if (INA219.begin(TELEM_WIRE)) { + MESH_DEBUG_PRINTLN("Found INA219 at address: %02X", TELEM_INA219_ADDRESS); + INA219_initialized = true; + } else { + INA219_initialized = false; + MESH_DEBUG_PRINTLN("INA219 did not initialize at I2C address %02X", TELEM_INA219_ADDRESS); + } + } else { + INA219_initialized = false; + MESH_DEBUG_PRINTLN("No I2C device found at address %02X (INA219)", TELEM_INA219_ADDRESS); + } #endif #if ENV_INCLUDE_INA260 -static uint8_t init_ina260(TwoWire* wire, uint8_t addr) { - return INA260.begin(addr, wire) ? 1 : 0; -} -static void query_ina260(uint8_t ch, uint8_t, CayenneLPP& lpp) { - lpp.addVoltage(ch, INA260.readBusVoltage() / 1000.0f); - lpp.addCurrent(ch, INA260.readCurrent() / 1000.0f); - lpp.addPower(ch, INA260.readPower() / 1000.0f); -} + if (i2c_device_exists(TELEM_WIRE, TELEM_INA260_ADDRESS)) { + if (INA260.begin(TELEM_INA260_ADDRESS, TELEM_WIRE)) { + MESH_DEBUG_PRINTLN("Found INA260 at address: %02X", TELEM_INA260_ADDRESS); + INA260_initialized = true; + } else { + INA260_initialized = false; + MESH_DEBUG_PRINTLN("INA260 did not initialize at I2C address %02X", TELEM_INA260_ADDRESS); + } + } else { + INA260_initialized = false; + MESH_DEBUG_PRINTLN("INA260 was not found at I2C address %02X", TELEM_INA260_ADDRESS); + } #endif #if ENV_INCLUDE_INA226 -static uint8_t init_ina226(TwoWire*, uint8_t) { - // INA226 static instance was constructed with address and wire. - if (!INA226.begin()) return 0; - INA226.setMaxCurrentShunt(TELEM_INA226_MAX_AMP, TELEM_INA226_SHUNT_VALUE); - return 1; -} -static void query_ina226(uint8_t ch, uint8_t, CayenneLPP& lpp) { - lpp.addVoltage(ch, INA226.getBusVoltage()); - lpp.addCurrent(ch, INA226.getCurrent_mA() / 1000.0f); - lpp.addPower(ch, INA226.getPower_mW() / 1000.0f); -} + if (i2c_device_exists(TELEM_WIRE, TELEM_INA226_ADDRESS)) { + if (INA226_sensor.begin()) { + MESH_DEBUG_PRINTLN("Found INA226 at address: %02X", TELEM_INA226_ADDRESS); + INA226_sensor.setMaxCurrentShunt(TELEM_INA226_MAX_AMP, TELEM_INA226_SHUNT_VALUE); + INA226_initialized = true; + } else { + INA226_initialized = false; + MESH_DEBUG_PRINTLN("INA226 did not initialize at I2C address %02X", TELEM_INA226_ADDRESS); + } + } else { + INA226_initialized = false; + MESH_DEBUG_PRINTLN("No I2C device found at address %02X (INA226)", TELEM_INA226_ADDRESS); + } #endif #if ENV_INCLUDE_MLX90614 -static uint8_t init_mlx90614(TwoWire* wire, uint8_t addr) { - return MLX90614.begin(addr, wire) ? 2 : 0; // 2 channels: object temp, ambient temp -} -static void query_mlx90614(uint8_t ch, uint8_t sub_ch, CayenneLPP& lpp) { - if (sub_ch == 0) - lpp.addTemperature(ch, MLX90614.readObjectTempC()); - else - lpp.addTemperature(ch, MLX90614.readAmbientTempC()); -} + if (i2c_device_exists(TELEM_WIRE, TELEM_MLX90614_ADDRESS)) { + if (MLX90614.begin(TELEM_MLX90614_ADDRESS, TELEM_WIRE)) { + MESH_DEBUG_PRINTLN("Found MLX90614 at address: %02X", TELEM_MLX90614_ADDRESS); + MLX90614_initialized = true; + } else { + MLX90614_initialized = false; + MESH_DEBUG_PRINTLN("MLX90614 did not initialize at I2C address %02X", TELEM_MLX90614_ADDRESS); + } + } else { + MLX90614_initialized = false; + MESH_DEBUG_PRINTLN("No I2C device found at address %02X (MLX90614)", TELEM_MLX90614_ADDRESS); + } #endif #if ENV_INCLUDE_VL53L0X -static uint8_t init_vl53l0x(TwoWire* wire, uint8_t addr) { - return VL53L0X.begin(addr, false, wire) ? 1 : 0; -} -static void query_vl53l0x(uint8_t ch, uint8_t, CayenneLPP& lpp) { - VL53L0X_RangingMeasurementData_t measure; - VL53L0X.rangingTest(&measure, false); - lpp.addDistance(ch, measure.RangeStatus != 4 ? measure.RangeMilliMeter / 1000.0f : 0.0f); -} + if (i2c_device_exists(TELEM_WIRE, TELEM_VL53L0X_ADDRESS)) { + if (VL53L0X.begin(TELEM_VL53L0X_ADDRESS, false, TELEM_WIRE)) { + MESH_DEBUG_PRINTLN("Found VL53L0X at address: %02X", TELEM_VL53L0X_ADDRESS); + VL53L0X_initialized = true; + } else { + VL53L0X_initialized = false; + MESH_DEBUG_PRINTLN("VL53L0X did not initialize at I2C address %02X", TELEM_VL53L0X_ADDRESS); + } + } else { + VL53L0X_initialized = false; + MESH_DEBUG_PRINTLN("No I2C device found at address %02X (VL53L0X)", TELEM_VL53L0X_ADDRESS); + } #endif -#ifdef ENV_INCLUDE_BMP085 -static uint8_t init_bmp085(TwoWire* wire, uint8_t) { - return BMP085.begin(0, wire) ? 1 : 0; // mode 0 = ULTRALOWPOWER -} -static void query_bmp085(uint8_t ch, uint8_t, CayenneLPP& lpp) { - lpp.addTemperature(ch, BMP085.readTemperature()); - lpp.addBarometricPressure(ch, BMP085.readPressure() / 100); - lpp.addAltitude(ch, BMP085.readAltitude(TELEM_BMP085_SEALEVELPRESSURE_HPA * 100)); -} +#if ENV_INCLUDE_BMP085 +#if ENV_INCLUDE_BME680 && (TELEM_BME680_ADDRESS == 0x77 || TELEM_BME680_ADDRESS == 0x76) + BMP085_initialized = false; + MESH_DEBUG_PRINTLN("Skipping BMP085 - BME680 is using address 0x77"); +#else + if (i2c_device_exists(TELEM_WIRE, 0x77)) { + if (BMP085.begin(0, TELEM_WIRE)) { + MESH_DEBUG_PRINTLN("Found sensor BMP085"); + BMP085_initialized = true; + } else { + BMP085_initialized = false; + MESH_DEBUG_PRINTLN("BMP085 did not initialize at I2C address %02X", 0x77); + } + } else { + BMP085_initialized = false; + MESH_DEBUG_PRINTLN("No I2C device found at address %02X (BMP085)", 0x77); + } +#endif #endif #if ENV_INCLUDE_RAK12035 -static uint8_t init_rak12035(TwoWire* wire, uint8_t addr) { - // RAK12035 requires setup() before begin(). - RAK12035.setup(*wire); - if (!RAK12035.begin(addr)) return 0; -#ifdef ENABLE_RAK12035_CALIBRATION - return 2; // moisture channel + calibration channel -#else - return 1; -#endif -} -static void query_rak12035(uint8_t ch, uint8_t sub_ch, CayenneLPP& lpp) { - if (sub_ch == 0) { - lpp.addTemperature(ch, RAK12035.get_sensor_temperature()); - lpp.addPercentage(ch, RAK12035.get_sensor_moisture()); + RAK12035.setup(*TELEM_WIRE); + if (RAK12035.begin(TELEM_RAK12035_ADDRESS)) { + MESH_DEBUG_PRINTLN("Found sensor RAK12035 at address: %02X", TELEM_RAK12035_ADDRESS); + RAK12035_initialized = true; } else { -#ifdef ENABLE_RAK12035_CALIBRATION - float cap = RAK12035.get_sensor_capacitance(); - float wet = RAK12035.get_humidity_full(); - float dry = RAK12035.get_humidity_zero(); - lpp.addFrequency(ch, cap); - lpp.addTemperature(ch, wet); - lpp.addPower(ch, dry); - if (cap > dry) RAK12035.set_humidity_zero(cap); - if (cap < wet) RAK12035.set_humidity_full(cap); -#endif + RAK12035_initialized = false; + MESH_DEBUG_PRINTLN("RAK12035 was not found at I2C address %02X", TELEM_RAK12035_ADDRESS); } -} #endif -#if ENV_INCLUDE_BME680_BSEC -static void bsec_load_state() { - using namespace Adafruit_LittleFS_Namespace; - File f = InternalFS.open(BSEC_STATE_FILE, FILE_O_READ); - if (!f) return; - uint8_t state[BSEC_MAX_STATE_BLOB_SIZE]; - f.read(state, BSEC_MAX_STATE_BLOB_SIZE); - f.close(); - bsec_iaq.setState(state); -} - -static void bsec_save_state() { - using namespace Adafruit_LittleFS_Namespace; - uint8_t state[BSEC_MAX_STATE_BLOB_SIZE]; - bsec_iaq.getState(state); - InternalFS.remove(BSEC_STATE_FILE); - File f = InternalFS.open(BSEC_STATE_FILE, FILE_O_WRITE); - if (!f) return; - f.write(state, BSEC_MAX_STATE_BLOB_SIZE); - f.close(); + return true; } -static uint8_t init_bme680_bsec(TwoWire* wire, uint8_t addr) { - bsec_iaq.begin(addr, *wire); - if (bsec_iaq.bsecStatus != BSEC_OK) return 0; - - bsec_iaq.setConfig(bsec_config_iaq); - if (bsec_iaq.bsecStatus != BSEC_OK) return 0; - - bsec_virtual_sensor_t outputs[] = { - BSEC_OUTPUT_IAQ, - BSEC_OUTPUT_SENSOR_HEAT_COMPENSATED_TEMPERATURE, - BSEC_OUTPUT_SENSOR_HEAT_COMPENSATED_HUMIDITY, - BSEC_OUTPUT_RAW_PRESSURE, - BSEC_OUTPUT_STABILIZATION_STATUS, - BSEC_OUTPUT_RUN_IN_STATUS, - }; - bsec_iaq.updateSubscription(outputs, 6, BSEC_SAMPLE_RATE_LP); - if (bsec_iaq.bsecStatus != BSEC_OK) return 0; - - bsec_load_state(); - bsec_active = true; - return 1; -} +// ============================================================ +// querySensors() +// ============================================================ -static void query_bme680_bsec(uint8_t ch, uint8_t, CayenneLPP& lpp) { - if (!bsec_data_ready) return; - lpp.addTemperature(ch, bsec_temperature); - lpp.addRelativeHumidity(ch, bsec_humidity); - lpp.addBarometricPressure(ch, bsec_pressure_hpa); - lpp.addAltitude(ch, 44330.0f * (1.0f - powf(bsec_pressure_hpa / (float)TELEM_BME680_SEALEVELPRESSURE_HPA, 0.1903f))); - lpp.addGenericSensor(ch, (uint16_t)bsec_iaq_val); - lpp.addAnalogInput(ch, (float)bsec_accuracy); -} +bool EnvironmentSensorManager::querySensors(uint8_t requester_permissions, CayenneLPP &telemetry) { + // I2C bus recovery voordat we sensors uitlezen +#if ENV_PIN_SDA && ENV_PIN_SCL && defined(ESP32) + static uint32_t last_i2c_error_time = 0; + static uint8_t consecutive_errors = 0; + + if (consecutive_errors > 3 && (millis() - last_i2c_error_time) < 5000) { + MESH_DEBUG_PRINTLN("I2C instability detected, attempting recovery..."); + Wire1.end(); + delay(10); + Wire1.begin(ENV_PIN_SDA, ENV_PIN_SCL, 100000); + delay(50); + consecutive_errors = 0; + last_i2c_error_time = millis(); + } #endif -// ============================================================ -// Sensor descriptor table -// -// Each entry maps an I2C address to a sensor's init and query -// functions. Only entries whose ENV_INCLUDE_* guard is defined -// are compiled in. The sentinel at the end keeps the array -// non-empty regardless of which sensors are enabled. -// -// Bosch BMP/BME SDO selects 0x76 or 0x77; probe both. -// -// Ordering here determines channel assignment at runtime: -// the first detected+initialized sensor gets channel 2, the -// next gets channel 3, and so on. -// ============================================================ + next_available_channel = TELEM_CHANNEL_SELF + 1; -struct SensorDef { - uint8_t address; - const char* name; - uint8_t (*init)(TwoWire* wire, uint8_t address); - void (*query)(uint8_t channel, uint8_t sub_channel, CayenneLPP& telemetry); -}; +#if ENV_INCLUDE_GPS + if (requester_permissions & TELEM_PERM_LOCATION && gps_active) { + telemetry.addGPS(TELEM_CHANNEL_SELF, node_lat, node_lon, + node_altitude - get_geoidal_separation(node_lat, node_lon)); + telemetry.addAnalogOutput(TELEM_CHANNEL_SELF, _location->satellitesCount()); + } +#endif -#define TELEM_BOSCH_ALT_ADDR(addr) ((uint8_t)((addr) == 0x76 ? 0x77 : 0x76)) + if (requester_permissions & TELEM_PERM_ENVIRONMENT) { -static const SensorDef SENSOR_TABLE[] = { #if ENV_INCLUDE_AHTX0 - { TELEM_AHTX_ADDRESS, "AHT10/AHT20", init_ahtx0, query_ahtx0 }, + if (AHTX0_initialized) { + sensors_event_t humidity, temp; + AHTX0.getEvent(&humidity, &temp); + telemetry.addTemperature(TELEM_CHANNEL_SELF, temp.temperature); + telemetry.addRelativeHumidity(TELEM_CHANNEL_SELF, humidity.relative_humidity); + } #endif -#ifdef ENV_INCLUDE_BME680 - { TELEM_BME680_ADDRESS, "BME680", init_bme680, query_bme680 }, - { TELEM_BOSCH_ALT_ADDR(TELEM_BME680_ADDRESS), "BME680", init_bme680, query_bme680 }, + +#if ENV_INCLUDE_BME680 + if (BME680_initialized) { + telemetry.addTemperature(next_available_channel, bme680_temperature); + telemetry.addRelativeHumidity(next_available_channel, bme680_humidity); + telemetry.addBarometricPressure(next_available_channel, bme680_pressure); + telemetry.addAltitude(next_available_channel, bme680_altitude); + telemetry.addGenericSensor(next_available_channel, bme680_gas_resistance); +#ifdef BME680_BSEC2_SUPPORTED + telemetry.addAnalogOutput(next_available_channel, bme680_iaq); + telemetry.addPresence(next_available_channel, bme680_iaq_accuracy); #endif -#if ENV_INCLUDE_BME680_BSEC - { TELEM_BME680_ADDRESS, "BME680+BSEC", init_bme680_bsec, query_bme680_bsec }, - { TELEM_BOSCH_ALT_ADDR(TELEM_BME680_ADDRESS), "BME680+BSEC", init_bme680_bsec, query_bme680_bsec }, + next_available_channel++; + } #endif + #if ENV_INCLUDE_BME280 - { TELEM_BME280_ADDRESS, "BME280", init_bme280, query_bme280 }, - { TELEM_BOSCH_ALT_ADDR(TELEM_BME280_ADDRESS), "BME280", init_bme280, query_bme280 }, + if (BME280_initialized) { + if (BME280.takeForcedMeasurement()) { + float temp_reading = BME280.readTemperature(); + if (!isnan(temp_reading) && temp_reading > -40 && temp_reading < 85) { + telemetry.addTemperature(TELEM_CHANNEL_SELF, temp_reading); + telemetry.addRelativeHumidity(TELEM_CHANNEL_SELF, BME280.readHumidity()); + telemetry.addBarometricPressure(TELEM_CHANNEL_SELF, BME280.readPressure() / 100); + telemetry.addAltitude(TELEM_CHANNEL_SELF, BME280.readAltitude(TELEM_BME280_SEALEVELPRESSURE_HPA)); + } else { + BME280_initialized = false; + MESH_DEBUG_PRINTLN("BME280 read failed, disabling sensor"); + } + } + } #endif + #if ENV_INCLUDE_BMP280 - { TELEM_BMP280_ADDRESS, "BMP280", init_bmp280, query_bmp280 }, - { TELEM_BOSCH_ALT_ADDR(TELEM_BMP280_ADDRESS), "BMP280", init_bmp280, query_bmp280 }, + if (BMP280_initialized) { + telemetry.addTemperature(TELEM_CHANNEL_SELF, BMP280.readTemperature()); + telemetry.addBarometricPressure(TELEM_CHANNEL_SELF, BMP280.readPressure() / 100); + telemetry.addAltitude(TELEM_CHANNEL_SELF, BMP280.readAltitude(TELEM_BMP280_SEALEVELPRESSURE_HPA)); + } #endif + #if ENV_INCLUDE_SHTC3 - { 0x70, "SHTC3", init_shtc3, query_shtc3 }, + if (SHTC3_initialized) { + sensors_event_t humidity, temp; + SHTC3.getEvent(&humidity, &temp); + telemetry.addTemperature(TELEM_CHANNEL_SELF, temp.temperature); + telemetry.addRelativeHumidity(TELEM_CHANNEL_SELF, humidity.relative_humidity); + } #endif + #if ENV_INCLUDE_SHT4X - { TELEM_SHT4X_ADDRESS, "SHT4X", init_sht4x, query_sht4x }, + if (SHT4X_initialized) { + float sht4x_humidity, sht4x_temperature; + int16_t sht4x_error = SHT4X.measureLowestPrecision(sht4x_temperature, sht4x_humidity); + if (sht4x_error == 0) { + telemetry.addTemperature(TELEM_CHANNEL_SELF, sht4x_temperature); + telemetry.addRelativeHumidity(TELEM_CHANNEL_SELF, sht4x_humidity); + } + } #endif + #if ENV_INCLUDE_LPS22HB - { 0x5C, "LPS22HB", init_lps22hb, query_lps22hb }, + if (LPS22HB_initialized) { + telemetry.addTemperature(TELEM_CHANNEL_SELF, LPS22HB.readTemperature()); + telemetry.addBarometricPressure(TELEM_CHANNEL_SELF, LPS22HB.readPressure() * 10); + } #endif + #if ENV_INCLUDE_INA3221 - { TELEM_INA3221_ADDRESS, "INA3221", init_ina3221, query_ina3221 }, + if (INA3221_initialized) { + for (int i = 0; i < TELEM_INA3221_NUM_CHANNELS; i++) { + if (INA3221.isChannelEnabled(i)) { + float voltage = INA3221.getBusVoltage(i); + float current = INA3221.getCurrentAmps(i); + telemetry.addVoltage(next_available_channel, voltage); + telemetry.addCurrent(next_available_channel, current); + telemetry.addPower(next_available_channel, voltage * current); + next_available_channel++; + } + } + } #endif + #if ENV_INCLUDE_INA219 - { TELEM_INA219_ADDRESS, "INA219", init_ina219, query_ina219 }, + if (INA219_initialized) { + telemetry.addVoltage(next_available_channel, INA219.getBusVoltage_V()); + telemetry.addCurrent(next_available_channel, INA219.getCurrent_mA() / 1000); + telemetry.addPower(next_available_channel, INA219.getPower_mW() / 1000); + next_available_channel++; + } #endif + #if ENV_INCLUDE_INA260 - { TELEM_INA260_ADDRESS, "INA260", init_ina260, query_ina260 }, + if (INA260_initialized) { + telemetry.addVoltage(next_available_channel, INA260.readBusVoltage() / 1000); + telemetry.addCurrent(next_available_channel, INA260.readCurrent() / 1000); + telemetry.addPower(next_available_channel, INA260.readPower() / 1000); + next_available_channel++; + } #endif + #if ENV_INCLUDE_INA226 - { TELEM_INA226_ADDRESS, "INA226", init_ina226, query_ina226 }, + if (INA226_initialized) { + telemetry.addVoltage(next_available_channel, INA226_sensor.getBusVoltage()); + telemetry.addCurrent(next_available_channel, INA226_sensor.getCurrent_mA() / 1000.0); + telemetry.addPower(next_available_channel, INA226_sensor.getPower_mW() / 1000.0); + next_available_channel++; + } #endif + #if ENV_INCLUDE_MLX90614 - { TELEM_MLX90614_ADDRESS,"MLX90614", init_mlx90614, query_mlx90614 }, + if (MLX90614_initialized) { + telemetry.addTemperature(TELEM_CHANNEL_SELF, MLX90614.readObjectTempC()); + telemetry.addTemperature(TELEM_CHANNEL_SELF + 1, MLX90614.readAmbientTempC()); + } #endif + #if ENV_INCLUDE_VL53L0X - { TELEM_VL53L0X_ADDRESS, "VL53L0X", init_vl53l0x, query_vl53l0x }, -#endif -#ifdef ENV_INCLUDE_BMP085 - { 0x77, "BMP085", init_bmp085, query_bmp085 }, -#endif -#if ENV_INCLUDE_RAK12035 - { TELEM_RAK12035_ADDRESS,"RAK12035", init_rak12035, query_rak12035 }, + if (VL53L0X_initialized) { + VL53L0X_RangingMeasurementData_t measure; + VL53L0X.rangingTest(&measure, false); + if (measure.RangeStatus != 4) { + telemetry.addDistance(TELEM_CHANNEL_SELF, measure.RangeMilliMeter / 1000.0f); + } else { + telemetry.addDistance(TELEM_CHANNEL_SELF, 0.0f); + } + } #endif - { 0, nullptr, nullptr, nullptr } // sentinel — keeps the array non-empty -}; - -#undef TELEM_BOSCH_ALT_ADDR - -static const size_t SENSOR_TABLE_SIZE = (sizeof(SENSOR_TABLE) / sizeof(SENSOR_TABLE[0])) - 1; - -// ============================================================ -// begin() — scan the I2C bus, then initialize only what was -// found. A sensor whose address does not ACK during the scan -// is never touched by a library call, preventing hangs or -// crashes caused by absent or misbehaving hardware. -// ============================================================ - -bool EnvironmentSensorManager::begin() { - #if ENV_INCLUDE_GPS - #ifdef RAK_WISBLOCK_GPS - rakGPSInit(); - #else - initBasicGPS(); - #endif - #endif - - #if ENV_PIN_SDA && ENV_PIN_SCL - #ifdef NRF52_PLATFORM - Wire1.setPins(ENV_PIN_SDA, ENV_PIN_SCL); - Wire1.setClock(100000); - Wire1.begin(); - #else - Wire1.begin(ENV_PIN_SDA, ENV_PIN_SCL, 100000); - #endif - MESH_DEBUG_PRINTLN("Second I2C initialized on pins SDA: %d SCL: %d", ENV_PIN_SDA, ENV_PIN_SCL); - #endif - - // Scan the I2C bus before touching any sensor library. - bool detected[128] = {}; - scanI2CBus(TELEM_WIRE, detected); - // Walk the sensor table and initialize only detected devices. - _active_sensor_count = 0; - for (size_t i = 0; i < SENSOR_TABLE_SIZE && _active_sensor_count < MAX_ACTIVE_SENSORS; i++) { - const SensorDef& def = SENSOR_TABLE[i]; - // One static driver instance per type: an alternate address is a fallback, not a second device. - bool already_active = false; - for (int j = 0; j < _active_sensor_count; j++) { - if (_active_sensors[j].query == def.query) { already_active = true; break; } +#if ENV_INCLUDE_BMP085 + if (BMP085_initialized) { + telemetry.addTemperature(TELEM_CHANNEL_SELF, BMP085.readTemperature()); + telemetry.addBarometricPressure(TELEM_CHANNEL_SELF, BMP085.readPressure() / 100); + telemetry.addAltitude(TELEM_CHANNEL_SELF, BMP085.readAltitude(TELEM_BMP085_SEALEVELPRESSURE_HPA * 100)); } - if (already_active) continue; - if (!detected[def.address]) { - MESH_DEBUG_PRINTLN("%s not detected at I2C address %02X", def.name, def.address); - continue; - } - uint8_t n = def.init(TELEM_WIRE, def.address); - if (n == 0) { - MESH_DEBUG_PRINTLN("%s found at %02X but failed to initialize", def.name, def.address); - continue; - } - MESH_DEBUG_PRINTLN("Found %s at address: %02X", def.name, def.address); - detected[def.address] = false; // consumed; later entries must not re-claim this device - for (uint8_t sub = 0; sub < n && _active_sensor_count < MAX_ACTIVE_SENSORS; sub++) { - _active_sensors[_active_sensor_count++] = { def.query, sub }; - } - } - - return true; -} - -// ============================================================ -// querySensors() — GPS stays on channel 1; each active sensor -// gets the next available channel in the order it was -// initialized. -// ============================================================ +#endif -bool EnvironmentSensorManager::querySensors(uint8_t requester_permissions, CayenneLPP& telemetry) { - next_available_channel = TELEM_CHANNEL_SELF + 1; +#if ENV_INCLUDE_RAK12035 + if (RAK12035_initialized) { + telemetry.addTemperature(2, RAK12035.get_sensor_temperature()); + telemetry.addPercentage(2, RAK12035.get_sensor_moisture()); + #ifdef ENABLE_RAK12035_CALIBRATION + float cap = RAK12035.get_sensor_capacitance(); + float _wet = RAK12035.get_humidity_full(); + float _dry = RAK12035.get_humidity_zero(); + telemetry.addFrequency(3, cap); + telemetry.addTemperature(3, _wet); + telemetry.addPower(3, _dry); + if (cap > _dry) RAK12035.set_humidity_zero(cap); + if (cap < _wet) RAK12035.set_humidity_full(cap); + #endif + } +#endif - if (requester_permissions & TELEM_PERM_LOCATION && gps_active) { - telemetry.addGPS(TELEM_CHANNEL_SELF, node_lat, node_lon, node_altitude); - } +#if ENV_PIN_SDA && ENV_PIN_SCL && defined(ESP32) + consecutive_errors = 0; +#endif - if (requester_permissions & TELEM_PERM_ENVIRONMENT) { - for (int i = 0; i < _active_sensor_count; i++) { - _active_sensors[i].query(next_available_channel, _active_sensors[i].sub_channel, telemetry); - next_available_channel++; - } } return true; } - int EnvironmentSensorManager::getNumSettings() const { int settings = 0; - #if ENV_INCLUDE_GPS - if (gps_detected) settings++; // only show GPS setting if GPS is detected - #endif +#if ENV_INCLUDE_GPS + if (gps_detected) settings++; +#endif return settings; } -const char* EnvironmentSensorManager::getSettingName(int i) const { +const char *EnvironmentSensorManager::getSettingName(int i) const { int settings = 0; - #if ENV_INCLUDE_GPS - if (gps_detected && i == settings++) { - return "gps"; - } - #endif +#if ENV_INCLUDE_GPS + if (gps_detected && i == settings++) { + return "gps"; + } +#endif + // convenient way to add params (needed for some tests) + // if (i == settings++) return "param.2"; return NULL; } -const char* EnvironmentSensorManager::getSettingValue(int i) const { +const char *EnvironmentSensorManager::getSettingValue(int i) const { int settings = 0; - #if ENV_INCLUDE_GPS - if (gps_detected && i == settings++) { - return gps_active ? "1" : "0"; - } - #endif +#if ENV_INCLUDE_GPS + if (gps_detected && i == settings++) { + return gps_active ? "1" : "0"; + } +#endif + // convenient way to add params ... + // if (i == settings++) return "2"; return NULL; } -bool EnvironmentSensorManager::setSettingValue(const char* name, const char* value) { - #if ENV_INCLUDE_GPS +bool EnvironmentSensorManager::setSettingValue(const char *name, const char *value) { +#if ENV_INCLUDE_GPS if (gps_detected && strcmp(name, "gps") == 0) { if (strcmp(value, "0") == 0) { stop_gps(); @@ -739,80 +948,103 @@ bool EnvironmentSensorManager::setSettingValue(const char* name, const char* val } if (strcmp(name, "gps_interval") == 0) { uint32_t interval_seconds = atoi(value); - gps_update_interval_sec = interval_seconds > 0 ? interval_seconds : 1; + if (interval_seconds > 0) { + gps_update_interval_sec = interval_seconds; + } else { + gps_update_interval_sec = 1; + } return true; } - #endif - return false; // not supported +#endif + return false; } #if ENV_INCLUDE_GPS void EnvironmentSensorManager::initBasicGPS() { + MESH_DEBUG_PRINTLN("PIN_GPS_TX %d, PIN_GPS_RX %d", PIN_GPS_TX, PIN_GPS_RX); - Serial1.setPins(PIN_GPS_TX, PIN_GPS_RX); +#ifdef GPS_BAUD_RATE + Serial1.begin(GPS_BAUD_RATE, SERIAL_8N1, PIN_GPS_RX, PIN_GPS_TX); + MESH_DEBUG_PRINTLN("GPS Serial initialized at %d baud", GPS_BAUD_RATE); +#else + Serial1.begin(9600, SERIAL_8N1, PIN_GPS_RX, PIN_GPS_TX); + MESH_DEBUG_PRINTLN("GPS Serial initialized at 9600 baud"); +#endif - #ifdef GPS_BAUD_RATE - Serial1.begin(GPS_BAUD_RATE); - #else - Serial1.begin(9600); - #endif + delay(1000); - // Try to detect if GPS is physically connected to determine if we should expose the setting _location->begin(); _location->reset(); - #ifndef PIN_GPS_EN - MESH_DEBUG_PRINTLN("No GPS wake/reset pin found for this board. Continuing on..."); - #endif +#ifndef PIN_GPS_EN + MESH_DEBUG_PRINTLN("No GPS wake/reset pin found for this board. Continuing on..."); +#endif // Give the GPS time to power up and emit its first NMEA sentence. Cold-start // modules can take several seconds, so poll for up to ~5s instead of checking // once after a fixed 1s delay -- returning as soon as any data appears, so - // fast modules add no boot delay (issue #2258). + // fast modules add no boot delay. #ifdef ENV_SKIP_GPS_DETECT gps_detected = true; + MESH_DEBUG_PRINTLN("GPS detection skipped (ENV_SKIP_GPS_DETECT)"); +#elif defined(HELTEC_LORA_V3) + // On Heltec boards, assume GPS is present if we have a board pointer + // We can't power it on during init because board.begin() hasn't been called yet + gps_detected = (_board != nullptr); + if (gps_detected) { + MESH_DEBUG_PRINTLN("Heltec: GPS assumed present (board configured with GPS)"); + MESH_DEBUG_PRINTLN("GPS detection check: Serial1.available() = %d", Serial1.available()); + } else { + MESH_DEBUG_PRINTLN("Heltec: No board reference, GPS not configured"); + } #else + // For non-Heltec boards, poll for GPS data for up to ~5s gps_detected = false; for (int i = 0; i < 20 && !gps_detected; i++) { delay(250); gps_detected = (Serial1.available() > 0); } + MESH_DEBUG_PRINTLN("GPS detection check: Serial1.available() = %d", Serial1.available()); #endif if (gps_detected) { MESH_DEBUG_PRINTLN("GPS detected"); - #ifdef PERSISTANT_GPS - gps_active = true; - return; - #endif +#ifdef PERSISTANT_GPS + gps_active = false; + gps_needs_power_on = true; + MESH_DEBUG_PRINTLN("GPS marked for persistent mode (deferred power-on in loop)"); + return; +#endif } else { MESH_DEBUG_PRINTLN("No GPS detected"); } + _location->stop(); - gps_active = false; //Set GPS visibility off until setting is changed + gps_active = false; } -// gps code for rak might be moved to MicroNMEALoactionProvider -// or make a new location provider ... #ifdef RAK_WISBLOCK_GPS -void EnvironmentSensorManager::rakGPSInit(){ +void EnvironmentSensorManager::rakGPSInit() { Serial1.setPins(PIN_GPS_TX, PIN_GPS_RX); - #ifdef GPS_BAUD_RATE +#ifdef GPS_BAUD_RATE Serial1.begin(GPS_BAUD_RATE); - #else +#else Serial1.begin(9600); - #endif +#endif - //search for the correct IO standby pin depending on socket used - if(gpsIsAwake(WB_IO2)){ - } - else if(gpsIsAwake(WB_IO4)){ - } - else if(gpsIsAwake(WB_IO5)){ - } - else{ + // search for the correct IO standby pin depending on socket used + if (gpsIsAwake(WB_IO2)) { + // MESH_DEBUG_PRINTLN("RAK base board is RAK19007/10"); + // MESH_DEBUG_PRINTLN("GPS is installed on Socket A"); + } else if (gpsIsAwake(WB_IO4)) { + // MESH_DEBUG_PRINTLN("RAK base board is RAK19003/9"); + // MESH_DEBUG_PRINTLN("GPS is installed on Socket C"); + } else if (gpsIsAwake(WB_IO5)) { + // MESH_DEBUG_PRINTLN("RAK base board is RAK19001/11"); + // MESH_DEBUG_PRINTLN("GPS is installed on Socket F"); + } else { MESH_DEBUG_PRINTLN("No GPS found"); gps_active = false; gps_detected = false; @@ -820,35 +1052,33 @@ void EnvironmentSensorManager::rakGPSInit(){ return; } - #ifndef FORCE_GPS_ALIVE // for use with repeaters, until GPS toggle is implimented - //Now that GPS is found and set up, set to sleep for initial state +#ifndef FORCE_GPS_ALIVE stop_gps(); - #endif +#endif } -bool EnvironmentSensorManager::gpsIsAwake(uint8_t ioPin){ +bool EnvironmentSensorManager::gpsIsAwake(uint8_t ioPin) { - #if defined(ETHERNET_ENABLED) && defined(RAK_BOARD) - if (ioPin == WB_IO2) { - // WB_IO2 powers the Ethernet module on RAK baseboards. - return false; - } - #endif +#if defined(ETHERNET_ENABLED) && defined(RAK_BOARD) + if (ioPin == WB_IO2) { + // WB_IO2 powers the Ethernet module on RAK baseboards. + return false; + } +#endif - #ifndef RAK_3401 - //set initial waking state - pinMode(ioPin,OUTPUT); - digitalWrite(ioPin,LOW); +#ifndef RAK_3401 + // set initial waking state + pinMode(ioPin, OUTPUT); + digitalWrite(ioPin, LOW); delay(500); - digitalWrite(ioPin,HIGH); - #endif + digitalWrite(ioPin, HIGH); +#endif // give gps time to power up delay(500); - //Try to init RAK12500 on I2C - if (ublox_GNSS.begin(Wire) == true){ - MESH_DEBUG_PRINTLN("RAK12500 GPS init correctly with pin %i",ioPin); + if (ublox_GNSS.begin(Wire) == true) { + MESH_DEBUG_PRINTLN("RAK12500 GPS init correctly with pin %i", ioPin); ublox_GNSS.setI2COutput(COM_TYPE_UBX); ublox_GNSS.enableGNSS(true, SFE_UBLOX_GNSS_ID_GPS); ublox_GNSS.enableGNSS(true, SFE_UBLOX_GNSS_ID_GALILEO); @@ -863,13 +1093,12 @@ bool EnvironmentSensorManager::gpsIsAwake(uint8_t ioPin){ i2cGPSFlag = true; gps_active = true; gps_detected = true; - _location = &RAK12500_provider; return true; } else if (Serial1.available()) { MESH_DEBUG_PRINTLN("Serial GPS init correctly and is turned on"); #ifdef PIN_GPS_EN - if(PIN_GPS_EN){ + if (PIN_GPS_EN) { gpsResetPin = PIN_GPS_EN; } #endif @@ -879,85 +1108,202 @@ bool EnvironmentSensorManager::gpsIsAwake(uint8_t ioPin){ return true; } - #ifndef RAK_3401 +#ifndef RAK_3401 pinMode(ioPin, INPUT); - #endif +#endif MESH_DEBUG_PRINTLN("GPS did not init with this IO pin... try the next"); return false; } #endif void EnvironmentSensorManager::start_gps() { - gps_active = true; - #ifdef RAK_WISBLOCK_GPS + if (!gps_active) { +#ifdef RAK_WISBLOCK_GPS #ifndef RAK_3401 pinMode(gpsResetPin, OUTPUT); digitalWrite(gpsResetPin, HIGH); #endif + gps_active = true; return; - #endif +#endif - _location->begin(); - _location->reset(); +#ifdef HELTEC_LORA_V3 + if (_board) { + _board->periph_power.claim(); + MESH_DEBUG_PRINTLN("Heltec: Claimed peripheral power for GPS"); + digitalWrite(PIN_GPS_EN, HIGH); + delay(1000); + Serial1.println("$CFGSYS,h35155*68"); + MESH_DEBUG_PRINTLN("Heltec: GPS configuration command sent"); + MESH_DEBUG_PRINTLN("Waiting for gps to power up"); + delay(1000); + gps_active = true; + } +#endif + + _location->begin(); + _location->reset(); #ifndef PIN_GPS_EN - MESH_DEBUG_PRINTLN("Start GPS is N/A on this board. Actual GPS state unchanged"); + MESH_DEBUG_PRINTLN("Start GPS is N/A on this board. Actual GPS state unchanged"); #endif + } } void EnvironmentSensorManager::stop_gps() { - gps_active = false; - #ifdef RAK_WISBLOCK_GPS - #ifndef RAK_3401 // rak3401 shouldn't turn off WB_IO2 as it powers the PA + if (gps_active) { + gps_active = false; + +#ifdef RAK_WISBLOCK_GPS + #ifndef RAK_3401 pinMode(gpsResetPin, OUTPUT); digitalWrite(gpsResetPin, LOW); #endif return; - #endif +#endif - _location->stop(); + _location->stop(); - #ifndef PIN_GPS_EN - MESH_DEBUG_PRINTLN("Stop GPS is N/A on this board. Actual GPS state unchanged"); - #endif +#ifdef HELTEC_LORA_V3 + if (_board) { + _board->periph_power.release(); + MESH_DEBUG_PRINTLN("Heltec: Released peripheral power for GPS"); + } +#endif + +#ifndef PIN_GPS_EN + MESH_DEBUG_PRINTLN("Stop GPS (no enable pin on this board)"); +#endif + } } -#endif // ENV_INCLUDE_GPS +#endif -#if ENV_INCLUDE_GPS || defined(ENV_INCLUDE_BME680_BSEC) +#if ENV_INCLUDE_GPS || ENV_INCLUDE_BME680 || defined(ENV_INCLUDE_BME680_BSEC) void EnvironmentSensorManager::loop() { - #if ENV_INCLUDE_GPS - static unsigned long next_gps_update = 0; +#if ENV_INCLUDE_GPS + // Handle deferred GPS power-on for PERSISTANT_GPS mode + if (gps_needs_power_on && !gps_active) { + MESH_DEBUG_PRINTLN("Activating GPS (deferred from init)..."); + start_gps(); + gps_needs_power_on = false; + } + if (gps_active) { _location->loop(); } - if ((long)(millis() - next_gps_update) > 0) { - - if(gps_active){ - #ifdef RAK_WISBLOCK_GPS - if ((i2cGPSFlag || serialGPSFlag) && _location->isValid()) { - node_lat = ((double)_location->getLatitude())/1000000.; - node_lon = ((double)_location->getLongitude())/1000000.; - MESH_DEBUG_PRINTLN("lat %f lon %f", node_lat, node_lon); - node_altitude = ((double)_location->getAltitude()) / 1000.0; - MESH_DEBUG_PRINTLN("lat %f lon %f alt %f", node_lat, node_lon, node_altitude); - } - #else - if (_location->isValid()) { - node_lat = ((double)_location->getLatitude())/1000000.; - node_lon = ((double)_location->getLongitude())/1000000.; - MESH_DEBUG_PRINTLN("lat %f lon %f", node_lat, node_lon); - node_altitude = ((double)_location->getAltitude()) / 1000.0; - MESH_DEBUG_PRINTLN("lat %f lon %f alt %f", node_lat, node_lon, node_altitude); - } - #endif + + static unsigned long next_gps_update = 0; + if (millis() > next_gps_update) { + if (gps_active) { + static bool last_valid_state = false; + static long last_sat_count = 0; + bool currently_valid = _location->isValid(); + long current_sats = _location->satellitesCount(); + + static unsigned long last_status_log = 0; + bool should_log = (currently_valid != last_valid_state) || (current_sats != last_sat_count) || + (!currently_valid && (millis() - last_status_log > 10000)); + +#ifdef RAK_WISBLOCK_GPS + if ((i2cGPSFlag || serialGPSFlag) && _location->isValid()) { + if (should_log) { + MESH_DEBUG_PRINTLN("GPS FIX ACQUIRED: lat %.6f, lon %.6f, alt %.1fm, sats %ld", + ((double)_location->getLatitude()) / 1000000., + ((double)_location->getLongitude()) / 1000000., + ((double)_location->getAltitude()) / 1000.0, current_sats); + last_status_log = millis(); + } + node_lat = ((double)_location->getLatitude()) / 1000000.; + node_lon = ((double)_location->getLongitude()) / 1000000.; + node_altitude = ((double)_location->getAltitude()) / 1000.0; + } else if (should_log) { + MESH_DEBUG_PRINTLN("GPS searching... (sats: %ld, valid: %s)", current_sats, + _location->isValid() ? "YES" : "NO"); + last_status_log = millis(); + } +#else + if (_location->isValid()) { + if (should_log) { + MESH_DEBUG_PRINTLN("GPS FIX ACQUIRED: lat %.6f, lon %.6f, alt %.1fm, sats %ld", + ((double)_location->getLatitude()) / 1000000., + ((double)_location->getLongitude()) / 1000000., + ((double)_location->getAltitude()) / 1000.0, current_sats); + last_status_log = millis(); + } + node_lat = ((double)_location->getLatitude()) / 1000000.; + node_lon = ((double)_location->getLongitude()) / 1000000.; + node_altitude = ((double)_location->getAltitude()) / 1000.0; + } else if (should_log) { + MESH_DEBUG_PRINTLN("GPS searching... (sats: %ld, valid: %s)", current_sats, + _location->isValid() ? "YES" : "NO"); + last_status_log = millis(); + } +#endif + + last_valid_state = currently_valid; + last_sat_count = current_sats; } next_gps_update = millis() + (gps_update_interval_sec * 1000); } - #endif - #if ENV_INCLUDE_BME680_BSEC +#endif // ENV_INCLUDE_GPS + +#if ENV_INCLUDE_BME680 + unsigned long now = millis(); + + if (BME680_initialized) { +#ifdef BME680_BSEC2_SUPPORTED + if (now - last_bme680_reading >= 3000 || last_bme680_reading == 0) { + if (!BME680_BSEC.run()) { + MESH_DEBUG_PRINTLN("BSEC run failed, status: %d", BME680_BSEC.status); + } else { + bsecData temp_data = BME680_BSEC.getData(BSEC_OUTPUT_SENSOR_HEAT_COMPENSATED_TEMPERATURE); + bsecData hum_data = BME680_BSEC.getData(BSEC_OUTPUT_SENSOR_HEAT_COMPENSATED_HUMIDITY); + bsecData press_data = BME680_BSEC.getData(BSEC_OUTPUT_RAW_PRESSURE); + bsecData gas_data = BME680_BSEC.getData(BSEC_OUTPUT_RAW_GAS); + bsecData iaq_data = BME680_BSEC.getData(BSEC_OUTPUT_IAQ); + + if (temp_data.signal != 0 && press_data.signal != 0) { + bme680_temperature = temp_data.signal; + bme680_humidity = hum_data.signal; + bme680_pressure = press_data.signal / 100.0; + bme680_gas_resistance = gas_data.signal / 1000.0; + bme680_iaq = iaq_data.signal; + bme680_iaq_accuracy = iaq_data.accuracy; + bme680_altitude = 44330.0 * (1.0 - pow(bme680_pressure / TELEM_BME680_SEALEVELPRESSURE_HPA, 0.1903)); + last_bme680_reading = now; + + MESH_DEBUG_PRINTLN("BME680 (BSEC2): Temp=%.2f°C, Hum=%.2f%%, Press=%.2f hPa, Alt=%.2fm " + "Gas=%.0f kOhm, IAQ=%.2f, Acc=%d", + bme680_temperature, bme680_humidity, bme680_pressure, bme680_altitude, + bme680_gas_resistance, bme680_iaq, (int)bme680_iaq_accuracy); + } + } + } +#else + if (now - last_bme680_reading >= 3000 || last_bme680_reading == 0) { + BME680.begin(); + if (BME680.performReading()) { + bme680_temperature = BME680.temperature; + bme680_humidity = BME680.humidity; + bme680_pressure = BME680.pressure / 100; + bme680_gas_resistance = BME680.gas_resistance; + bme680_altitude = BME680.readAltitude(TELEM_BME680_SEALEVELPRESSURE_HPA); + last_bme680_reading = now; + + MESH_DEBUG_PRINTLN( + "BME680 (Adafruit): Temp=%.1f°C, Hum=%.1f%%, Press=%.1f hPa, Alt=%.1fm, Gas=%.0f Ohm", + bme680_temperature, bme680_humidity, bme680_pressure, bme680_altitude, bme680_gas_resistance); + } else { + MESH_DEBUG_PRINTLN("BME680 reading failed, keeping previous values"); + } + } +#endif + } +#endif // ENV_INCLUDE_BME680 + +#if ENV_INCLUDE_BME680_BSEC if (bsec_active && bsec_iaq.run()) { - uint8_t prev_accuracy = bsec_accuracy; bsec_temperature = bsec_iaq.temperature; bsec_humidity = bsec_iaq.humidity; bsec_pressure_hpa = bsec_iaq.pressure / 100.0f; @@ -976,6 +1322,7 @@ void EnvironmentSensorManager::loop() { } } } - #endif // ENV_INCLUDE_BME680_BSEC +#endif // ENV_INCLUDE_BME680_BSEC + } -#endif // ENV_INCLUDE_GPS || ENV_INCLUDE_BME680_BSEC +#endif // ENV_INCLUDE_GPS || ENV_INCLUDE_BME680 || ENV_INCLUDE_BME680_BSEC diff --git a/src/helpers/sensors/EnvironmentSensorManager.h b/src/helpers/sensors/EnvironmentSensorManager.h index 17706cbc492..b26eca02c85 100644 --- a/src/helpers/sensors/EnvironmentSensorManager.h +++ b/src/helpers/sensors/EnvironmentSensorManager.h @@ -1,54 +1,75 @@ #pragma once - #include #include #include +// Forward declaration for board-specific power management +class HeltecV3Board; + class EnvironmentSensorManager : public SensorManager { protected: - static const int MAX_ACTIVE_SENSORS = 16; - - // Query function pointer + sub-channel index (for multi-channel sensors like INA3221). - // Sub-channel is 0 for all single-output sensors. - struct ActiveSensor { - void (*query)(uint8_t channel, uint8_t sub_channel, CayenneLPP& telemetry); - uint8_t sub_channel; - }; - - ActiveSensor _active_sensors[MAX_ACTIVE_SENSORS]; - int _active_sensor_count = 0; - uint8_t next_available_channel = TELEM_CHANNEL_SELF + 1; + int next_available_channel = TELEM_CHANNEL_SELF + 1; + bool AHTX0_initialized = false; + bool BME280_initialized = false; + bool BMP280_initialized = false; + bool INA3221_initialized = false; + bool INA219_initialized = false; + bool INA260_initialized = false; + bool INA226_initialized = false; + bool SHTC3_initialized = false; + bool LPS22HB_initialized = false; + bool MLX90614_initialized = false; + bool VL53L0X_initialized = false; + bool SHT4X_initialized = false; + bool BME680_initialized = false; + bool BMP085_initialized = false; + bool RAK12035_initialized = false; + bool gps_detected = false; + bool gps_active = false; + uint32_t gps_update_interval_sec = 1; // Default 1 second - bool gps_detected = false; - bool gps_active = false; - uint32_t gps_update_interval_sec = 1; +#if ENV_INCLUDE_BME680 + unsigned long last_bme680_reading = 0; + float bme680_temperature = 0; + float bme680_humidity = 0; + float bme680_pressure = 0; + float bme680_gas_resistance = 0; + float bme680_altitude = 0; + float bme680_iaq = 0; // Indoor Air Quality index (only with BSEC2) + float bme680_iaq_accuracy = 0; // Indoor Air Quality accuracy (only with BSEC2) +#endif - #if ENV_INCLUDE_GPS - LocationProvider* _location; +#if ENV_INCLUDE_GPS + LocationProvider *_location; + HeltecV3Board *_board; // Optional board reference for power management + bool gps_needs_power_on = false; // Flag for deferred power-on in PERSISTANT_GPS mode void start_gps(); void stop_gps(); void initBasicGPS(); - #ifdef RAK_BOARD +#ifdef RAK_BOARD void rakGPSInit(); bool gpsIsAwake(uint8_t ioPin); - #endif - #endif +#endif +#endif public: - #if ENV_INCLUDE_GPS - EnvironmentSensorManager(LocationProvider &location): _location(&location){}; - LocationProvider* getLocationProvider() { return _location; } - bool isGPSDetected() const override { return gps_detected; } - #else - EnvironmentSensorManager(){}; - #endif +#if ENV_INCLUDE_GPS + EnvironmentSensorManager(LocationProvider &location, HeltecV3Board *board = nullptr) + : _location(&location), _board(board) {}; + LocationProvider *getLocationProvider() { return _location; } +#else + EnvironmentSensorManager() {}; +#endif + bool begin() override; - bool querySensors(uint8_t requester_permissions, CayenneLPP& telemetry) override; - #if ENV_INCLUDE_GPS || defined(ENV_INCLUDE_BME680_BSEC) + bool querySensors(uint8_t requester_permissions, CayenneLPP &telemetry) override; + +#if ENV_INCLUDE_GPS || ENV_INCLUDE_BME680 || defined(ENV_INCLUDE_BME680_BSEC) void loop() override; - #endif +#endif + int getNumSettings() const override; - const char* getSettingName(int i) const override; - const char* getSettingValue(int i) const override; - bool setSettingValue(const char* name, const char* value) override; -}; + const char *getSettingName(int i) const override; + const char *getSettingValue(int i) const override; + bool setSettingValue(const char *name, const char *value) override; +}; \ No newline at end of file diff --git a/src/helpers/sensors/config/bme680/bme680_iaq_33v_3s_4d/bsec_iaq.txt b/src/helpers/sensors/config/bme680/bme680_iaq_33v_3s_4d/bsec_iaq.txt new file mode 100644 index 00000000000..83f070403af --- /dev/null +++ b/src/helpers/sensors/config/bme680/bme680_iaq_33v_3s_4d/bsec_iaq.txt @@ -0,0 +1 @@ +0,1,6,2,189,1,0,0,0,0,0,0,127,7,0,0,56,0,1,0,0,192,168,71,64,49,119,76,0,0,97,69,0,0,97,69,10,0,3,0,0,0,96,64,23,183,209,56,43,24,149,60,140,74,106,188,43,24,149,60,216,129,243,190,151,255,80,190,216,129,243,190,8,0,2,0,0,0,72,66,16,0,3,0,10,215,163,60,10,215,35,59,10,215,35,59,13,0,5,0,0,0,0,0,100,35,41,29,86,88,0,9,0,229,208,34,62,0,0,0,0,0,0,0,0,218,27,156,62,225,11,67,64,0,0,160,64,0,0,0,0,0,0,0,0,94,75,72,189,93,254,159,64,66,62,160,191,0,0,0,0,0,0,0,0,33,31,180,190,138,176,97,64,65,241,99,190,0,0,0,0,0,0,0,0,167,121,71,61,165,189,41,192,184,30,189,64,12,0,10,0,0,0,0,0,0,0,0,0,45,5,11,0,1,1,2,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,10,10,4,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,128,63,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,145,1,254,0,2,1,5,48,117,100,0,44,1,112,23,151,7,132,3,197,0,92,4,144,1,64,1,64,1,144,1,48,117,48,117,48,117,48,117,100,0,100,0,100,0,48,117,48,117,48,117,100,0,100,0,48,117,48,117,8,7,8,7,8,7,8,7,8,7,8,7,8,7,8,7,8,7,100,0,100,0,100,0,100,0,48,117,48,117,48,117,100,0,100,0,100,0,48,117,48,117,100,0,100,0,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,44,1,44,1,44,1,44,1,44,1,44,1,44,1,44,1,44,1,44,1,44,1,44,1,44,1,44,1,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,112,23,112,23,112,23,112,23,8,7,8,7,8,7,8,7,112,23,112,23,112,23,112,23,112,23,112,23,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,112,23,112,23,112,23,112,23,255,255,255,255,220,5,220,5,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,220,5,220,5,220,5,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,44,1,0,5,10,5,0,2,0,10,0,30,0,5,0,5,0,5,0,5,0,5,0,5,0,64,1,100,0,100,0,100,0,200,0,200,0,200,0,64,1,64,1,64,1,10,0,0,0,0,0,0,87,13,0,0 \ No newline at end of file diff --git a/variants/heltec_tracker_v1_1/platformio.ini b/variants/heltec_tracker_v1_1/platformio.ini new file mode 100644 index 00000000000..b9f839126e2 --- /dev/null +++ b/variants/heltec_tracker_v1_1/platformio.ini @@ -0,0 +1,173 @@ +[Heltec_tracker_v1_1_base] +extends = esp32_base +board = esp32-s3-devkitc-1 +build_flags = + ${esp32_base.build_flags} + ${sensor_base.build_flags} + -I variants/heltec_tracker_v1_1 + -D HELTEC_LORA_V3 + -D ARDUINO_USB_CDC_ON_BOOT=1 ; need for Serial + -D ESP32_CPU_FREQ=80 + -D P_LORA_DIO_1=14 + -D P_LORA_NSS=8 + -D P_LORA_RESET=RADIOLIB_NC + -D P_LORA_BUSY=13 + -D P_LORA_SCLK=9 + -D P_LORA_MISO=11 + -D P_LORA_MOSI=10 + -D RADIO_CLASS=CustomSX1262 + -D WRAPPER_CLASS=CustomSX1262Wrapper + -D LORA_TX_POWER=22 + -D P_LORA_TX_LED=18 + -D PIN_BOARD_SDA=45 + -D PIN_BOARD_SCL=46 + -D PIN_USER_BTN=0 + -D PIN_ADC_CTRL=2 + -D PIN_TFT_SDA=42 ; SDIN + -D PIN_TFT_SCL=41 ; SCLK + -D PIN_TFT_DC=40 ; RS (register select) + -D PIN_TFT_RST=39 ; RES + -D PIN_TFT_CS=38 + -D USE_PIN_TFT=1 + -D PIN_VEXT_EN=3 ; Vext is connected to VDD which is also connected to OLED & GPS + -D PIN_TFT_LEDA_CTL=21 ; LEDK (switches on/off via mosfet to create the ground) + -D PIN_GPS_RX=33 + -D PIN_GPS_TX=34 + -D PIN_GPS_PPS=36 + -D PIN_GPS_RST=35 + -D PIN_GPS_EN=3 + -D ENV_PIN_SDA=PIN_BOARD_SDA + -D ENV_PIN_SCL=PIN_BOARD_SCL + -D ENV_INCLUDE_GPS=1 + -D ENV_INCLUDE_INA3221=1 + -D ENV_INCLUDE_BME680=1 + -D BME680_BSEC2_SUPPORTED=1 + -D ENV_INCLUDE_BMP085=0 + -D TELEM_BME680_ADDRESS=0x77 + -D GPS_BAUD_RATE=115200 + -D SX126X_DIO2_AS_RF_SWITCH=true + -D SX126X_DIO3_TCXO_VOLTAGE=1.8 + -D SX126X_CURRENT_LIMIT=140 + -D SX126X_RX_BOOSTED_GAIN=1 +build_src_filter = ${esp32_base.build_src_filter} + +<../variants/heltec_tracker_v1_1> + + +lib_deps = + ${esp32_base.lib_deps} + ${sensor_base.lib_deps} + stevemarple/MicroNMEA @ ^2.0.6 + bodmer/TFT_eSPI @ ^2.5.43 + +[env:Heltec_Wireless_Tracker_v1_1_companion_radio_ble] +extends = Heltec_tracker_v1_1_base +build_flags = + ${Heltec_tracker_v1_1_base.build_flags} + -I src/helpers/ui + -I examples/companion_radio/ui-new + -D ARDUINO_USB_CDC_ON_BOOT=1 ; need for Serial + -D DISPLAY_ROTATION=1 + -D DISPLAY_CLASS=ST7735Display + -D MAX_CONTACTS=300 + -D MAX_GROUP_CHANNELS=8 + -D BLE_PIN_CODE=123456 ; HWT will use display for pin + -D OFFLINE_QUEUE_SIZE=256 + -D BLE_DEBUG_LOGGING=1 + -D MESH_PACKET_LOGGING=1 + -D MESH_DEBUG=1 +build_src_filter = ${Heltec_tracker_v1_1_base.build_src_filter} + + + + + +<../examples/companion_radio/*.cpp> + +<../examples/companion_radio/ui-new/*.cpp> + + +lib_deps = + ${Heltec_tracker_v1_1_base.lib_deps} + densaugeo/base64 @ ~1.4.0 + +[env:Heltec_Wireless_Tracker_v1_1_repeater] +extends = Heltec_tracker_v1_1_base +build_flags = + ${Heltec_tracker_v1_1_base.build_flags} + -D DISPLAY_ROTATION=1 + -D DISPLAY_CLASS=ST7735Display + -D ADVERT_NAME='"Heltec Repeater"' + ; -D ADVERT_LAT=0.0 + ; -D ADVERT_LON=0.0 + -D PERSISTANT_GPS=1 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 + -D MESH_PACKET_LOGGING=1 + -D MESH_DEBUG=1 +build_src_filter = ${Heltec_tracker_v1_1_base.build_src_filter} + + + +<../examples/simple_repeater> +lib_deps = + ${Heltec_tracker_v1_1_base.lib_deps} + ${esp32_ota.lib_deps} + +; [env:Heltec_Wireless_Tracker_repeater_bridge_rs232] +; extends = Heltec_tracker_v1_1_base +; build_flags = +; ${Heltec_tracker_v1_1_base.build_flags} +; -D DISPLAY_ROTATION=1 +; -D DISPLAY_CLASS=ST7735Display +; -D ADVERT_NAME='"RS232 Bridge"' +; -D ADVERT_LAT=0.0 +; -D ADVERT_LON=0.0 +; -D ADMIN_PASSWORD='"password"' +; -D MAX_NEIGHBOURS=50 +; -D WITH_RS232_BRIDGE=Serial2 +; -D WITH_RS232_BRIDGE_RX=5 +; -D WITH_RS232_BRIDGE_TX=6 +; ; -D MESH_PACKET_LOGGING=1 +; ; -D MESH_DEBUG=1 +; build_src_filter = ${Heltec_tracker_v1_1_base.build_src_filter} +; + +; + +; +<../examples/simple_repeater> +; lib_deps = +; ${Heltec_tracker_v1_1_base.lib_deps} +; ${esp32_ota.lib_deps} + +[env:Heltec_Wireless_Tracker_v1_1_repeater_bridge_espnow] +extends = Heltec_tracker_v1_1_base +build_flags = + ${Heltec_tracker_v1_1_base.build_flags} + -D DISPLAY_ROTATION=1 + -D DISPLAY_CLASS=ST7735Display + -D ADVERT_NAME='"ESPNow Bridge"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D MAX_NEIGHBOURS=50 + -D WITH_ESPNOW_BRIDGE=1 + -D WITH_ESPNOW_BRIDGE_SECRET='"shared-secret"' +; -D MESH_PACKET_LOGGING=1 +; -D MESH_DEBUG=1 +build_src_filter = ${Heltec_tracker_v1_1_base.build_src_filter} + + + + + +<../examples/simple_repeater> +lib_deps = + ${Heltec_tracker_v1_1_base.lib_deps} + ${esp32_ota.lib_deps} + +[env:Heltec_Wireless_Tracker_room_server] +extends = Heltec_tracker_v1_1_base +build_flags = + ${Heltec_tracker_v1_1_base.build_flags} + -D DISPLAY_ROTATION=1 + -D DISPLAY_CLASS=ST7735Display + -D ADVERT_NAME='"Heltec Room"' + -D ADVERT_LAT=0.0 + -D ADVERT_LON=0.0 + -D ADMIN_PASSWORD='"password"' + -D ROOM_PASSWORD='"hello"' +; -D MESH_PACKET_LOGGING=1 +; -D MESH_DEBUG=1 +build_src_filter = ${Heltec_tracker_v1_1_base.build_src_filter} + + + +<../examples/simple_room_server> +lib_deps = + ${Heltec_tracker_v1_1_base.lib_deps} + ${esp32_ota.lib_deps} diff --git a/variants/heltec_tracker_v1_1/target.cpp b/variants/heltec_tracker_v1_1/target.cpp new file mode 100644 index 00000000000..8b0ad9a73a6 --- /dev/null +++ b/variants/heltec_tracker_v1_1/target.cpp @@ -0,0 +1,63 @@ +#include "target.h" + +#include +#include + +HeltecV3Board board; + +#if defined(P_LORA_SCLK) +static SPIClass spi; +RADIO_CLASS radio = new Module(P_LORA_NSS, P_LORA_DIO_1, P_LORA_RESET, P_LORA_BUSY, spi); +#else +RADIO_CLASS radio = new Module(P_LORA_NSS, P_LORA_DIO_1, P_LORA_RESET, P_LORA_BUSY); +#endif + +WRAPPER_CLASS radio_driver(radio, board); + +ESP32RTCClock fallback_clock; +AutoDiscoverRTCClock rtc_clock(fallback_clock); + +#if ENV_INCLUDE_GPS +#include +MicroNMEALocationProvider nmea = + MicroNMEALocationProvider(Serial1, &rtc_clock, PIN_GPS_RST, PIN_GPS_EN, &board.periph_power); +EnvironmentSensorManager sensors = EnvironmentSensorManager(nmea, &board); +#else +EnvironmentSensorManager sensors; +#endif + +#ifdef DISPLAY_CLASS +DISPLAY_CLASS display(&board.periph_power); // peripheral power pin is shared +MomentaryButton user_btn(PIN_USER_BTN, 1000, true); +#endif + +bool radio_init() { + fallback_clock.begin(); + rtc_clock.begin(Wire); + +#if defined(P_LORA_SCLK) + return radio.std_init(&spi); +#else + return radio.std_init(); +#endif +} + +uint32_t radio_get_rng_seed() { + return radio.random(0x7FFFFFFF); +} + +void radio_set_params(float freq, float bw, uint8_t sf, uint8_t cr) { + radio.setFrequency(freq); + radio.setSpreadingFactor(sf); + radio.setBandwidth(bw); + radio.setCodingRate(cr); +} + +void radio_set_tx_power(uint8_t dbm) { + radio.setOutputPower(dbm); +} + +mesh::LocalIdentity radio_new_identity() { + RadioNoiseListener rng(radio); + return mesh::LocalIdentity(&rng); // create new random identity +} diff --git a/variants/heltec_tracker_v1_1/target.h b/variants/heltec_tracker_v1_1/target.h new file mode 100644 index 00000000000..a5804d5237a --- /dev/null +++ b/variants/heltec_tracker_v1_1/target.h @@ -0,0 +1,31 @@ +#pragma once + +#define RADIOLIB_STATIC_ONLY 1 +#include <../heltec_v3/HeltecV3Board.h> +#include +#include +#include +#include +#include +#include +#include +#ifdef DISPLAY_CLASS +#include +#include +#endif + +extern HeltecV3Board board; +extern WRAPPER_CLASS radio_driver; +extern AutoDiscoverRTCClock rtc_clock; +extern EnvironmentSensorManager sensors; + +#ifdef DISPLAY_CLASS +extern DISPLAY_CLASS display; +extern MomentaryButton user_btn; +#endif + +bool radio_init(); +uint32_t radio_get_rng_seed(); +void radio_set_params(float freq, float bw, uint8_t sf, uint8_t cr); +void radio_set_tx_power(uint8_t dbm); +mesh::LocalIdentity radio_new_identity();